定向探测引信技术分析

从提高引信与战斗部配合效率出发 ,根据定向战斗部的战术技术性能 ,介绍了一种能够识别弹体周围 4个方向目标的定向探测引信 .分析了定向探测器的工作原理和目标方位识别的关键技术 ,并对探测天线的设计做了详细的分析和计算 .     

后压浆技术在杨凌国际会展中心基桩工程中应用效果的分析

本文叙述了杨凌国际会展中心基桩静力载荷试验的试验过程 ;通过对三根灌注桩承载力的试验结果分析 ,认为后压浆技术对提高灌注桩单桩极限承载力有很大作用     

The effect of a solid additive on rolling fatigue life

Behaviour of a series of lubricant oils and the effect of a non stoichiometric inorganic compound, as solid extreme pressure additive, on rolling fatigue life are studied using the rolling four-ball accelerated service simulation test proposed by Barwell and Scott. The results show, in all tested cases, the remarkable efficacy of this type of additive. The Total Acidity Number (tan) was found to increase with performance time for the case of the base lubricant, while for the oils with additives, it remained at its constant low value. This led to a proposal of a possible mechanism of the additive performance in the rolling process.     

轧机主传动万向联轴器辊端接头结构探讨

分析了衬板槽平面与叉头十字轴孔轴线的相对位置对辊端接头应力的影响 ,研究了轧辊扁头与衬板之间间隙所产生的冲击和应力集中 ,讨论了辊端接头中部过渡段结构对应力分布和制造质量的影响。提出辊端接头结构设计的优化方案     

淤泥质土状亚粘土的一些特征

珠江三角洲软土地区存在一种灰色亚粘土，其工程性能与淤泥、淤泥质土相似，但两者的物理力学性质却有明显的不同，这是一种在规范土名定义上处于过渡或边缘状态的粘性土，不是严格定义上的淤泥质土，也不是正常沉积的一般粘性土，土的强度和工程性质与淤泥质土类似，应该近沿海地区淤泥和淤泥质土对待，不应看成一般粘性土。     

冷轧带肋钢筋直径与拉丝机卷筒直径的匹配

采用被动式工艺生产冷轧带肋钢筋须经过减径、成型两台轧机连续轧制．要求钢材的秒流量相等，否则将造成断线停产或线材在拉丝机卷筒上打滑，致使卷筒严重磨损．用双层卷筒拉丝机提供动力生产冷轧带肋钢筋时，线材直径与卷筒直径的匹配是在一个小的调整范围，通过轧机拉力控制在一定范围变化，可保证成品尺寸符合公差要求而不产生打滑，从而避免了卷筒严重磨损．     

Failure analysis used for remanufacturing of steel rolling components

The guide-pieces, used in the process line of steel rolling, were the important components. The guidepieces, which were slide contacting with the rolled-piece, had a high temperature and high speed. The wear was very serious. The results from failure analysis showed that there were three failure forms in the guide-pieces: the first was the wear during heat friction, the second was the heat fatigue under the cycle of deep heating and deep cooling, and the third was the impact rupture. Among them, the wear was the main reason. To the wear of guidepieces, there were four mechanisms, namely abrasive wear, adhesive wear, fatigue wear and corrosion wear. The failure analysis to the guide-piece laid the foundation for its remanufacturing. Foundation item: Project(50235030) supported by the National Natural Science Foundation of China     

Precision equipment for symmetrical bending— Part 1. The loading system

The design and performance of precision bending equipment for testing straight beams with constant rectangular section under a pure bending moment is described. Part 1 deals with the loading arrangements and Part 2 with the rig for measuring beam deflection. The methods for recording deflection of strain gauges applied on the beam have been described elsewhere.^1–4
The reactions to the deadweight gravity loads are taken via ball bearings. The total bending moment inaccuracy, i.e. the sum of estimated systematic errors and random errors, the latter expressed as the 2Ga confidence interval about the mean (2G_cim), is about ± 25 x. 10^-4%, for 23 tests with a steel beam with 15 mm × 75 mm cross sectional dimensions, loaded to 1-1.5 mm/m strain.
The measuring rig stands on the beam via hardened and polished spherical segment feet and uses a capacitive transducer system with less than 5nm resolution. Various application tasks are described. The total inaccuracy of the measured deflection, i.e. apart from bending moment inaccuracy, is about ± 35 times 10^4% for about 10 reproduced, not repeated, tests with the same steel beam. The deflection for such a beam is of the order of 2 to 4 mm.     

Finite‐Element Implementation of a Self‐consistent Texture Model with a Hardening Law Based on Dislocation Densities

A self‐consistent texture model is implemented in the finite‐element code ABAQUS/Explicit®. Hardening of the slip systems is described by evolution laws for dislocation densities, and the Bauschinger effect is included. With these ingredients the cold rolling of an IF‐steel is simulated and the evolution of texture and anisotropy is examined. The use of the dislocation based hardening law is found to have a significant effect on the evolution of the anisotropic yield surface, but only very little influence on the texture. Furthermore, the hardening model is used to investigate the evolution of dislocation densities in differently oriented grains during plane strain compression. It is found that the dislocation density varies greatly depending on orientation, an observation which can help to explain the orientation dependence of recrystallization.     

薄板坯连铸连轧流程Ti微合金化高强钢开发与应用

在薄板坯连铸连轧流程上，经过对Ti微合金化技术研究，有效解决了Ti微合金化强度性能波动大的问题，开发出屈服强度450～700MPa高强钢。对试制钢组织性能和工业应用分析研究，表明该产品通板性能良好，通板强度差30MPa左右；成形性能良好，d=0时冷弯测试全部合格；同时还具有良好焊接性能，焊接后，强度波动较小，均在母材部位断开；试制钢显微组织为珠光体和铁素体，晶粒均匀细小，平均尺寸为4～8／μm；实物质量满足集装箱和汽车制造行业要求，具有广阔市场前景。