状态监测与分析系统在大型机组中的应用

介绍了S8000大型旋转机械状态监测与分析系统在催化大机组中的应用及故障诊断。     

原位TiCp/Fe复合材料的切削力及切屑形状

从退火态原位TiCp／Fe复合材料的切削力和切屑形状方面分析了其切削性能。研究结果表明其切削力及切削力的波动范围都小于铸态45钢，其切削性能比45钢好。TiCp／Fe复合材料的切屑为C形屑、长紧卷屑和发条状卷屑，在机加工中，产生这几种切屑是比较理想的。从切屑方面看，TiCp／Fe复合材料的切削性能较好。     

Improvement of levitation characteristics in a magnetic bearing system using HTSC‐permanent magnet hybrid structure

Magnetic bearing using pinning force of a permanent magnet and a high‐temperature superconductor has been developed. Additional permanent magnet is introduced to increase the levitation force of the magnetic bearing. In this hybrid magnetic bearing system, levitation force is mainly given by the repulsive force of the permanent magnets, and stability for the lateral direction is given by pinning force of the superconductor. The experimental device is developed. A ring‐type superconductor and a bulk one are examined. Levitation characteristics of the hybrid magnetic bearing are measured. The bulk superconductor shows better characteristics of both levitation and lateral stability than the ring one. Levitation force of the hybrid system becomes about twice as large as that of the nonhybrid one. Although, the repulsive force of the permanent magnet decreases the lateral stability of the system, its influence becomes small by choosing an adequate position of the permanent magnets and the superconductor. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(1): 71–77, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10350     

薄板坯连铸连轧工艺对铌微合金化高强度钢组织和性能的影响

首先建立薄板坯连铸连轧工艺的试验室模拟技术，并运用该模拟技术，研究薄板坯连铸连轧工艺(CSP)和传统板坯再加热工艺(TRP)两种工艺对铌微合金化高强度钢的显微组织和力学性能的影响。研究结果表明：CSP钢的晶粒细化效果不如TRP钢，两者的平均铁素体晶粒尺寸分别为8．17μm和6．30μm。在CSP试验钢板中铌的析出量较大，特别是在铁素体中细小颗粒的铌的析出物较多，沉淀强化效果较强。CSP试验钢的σ0.5和σb分别较TRP工艺低约40MPa和约25MPa，同时其低温冲击韧性较好，FATT温度较低。     

滚动转子式压缩机传热模拟

就滚动转子式压缩机的传热特性进行了分析。把压缩机分为15块，视摩擦损失和电机发热为内热源，考虑润滑油流动在传热过程中的影响，应用集中参数法对每块进行了能量分析，建立了传热数学模型并进行了计算。     

Analytic methods for modeling longitudinal data from rolling therapy groups with membership turnover.

Interventions for a variety of emotional and behavioral problems are commonly delivered in the context of treatment groups, with many using rolling admission to sustain membership (i.e., admission, dropout, and discharge from group are perpetual and ongoing). The authors present an overview of the analytic challenges inherent in rolling group data and outline commonly used (but flawed) analytic and design approaches to addressing (or sidestepping) these issues. Moreover, the authors propose use of latent class pattern mixture models (LCPMMs) as a statistically and conceptually defensible approach for modeling treatment data from rolling groups. The LCPMM approach is illustrated with rolling group data from a group-based alcoholism pilot treatment trial (N = 128). Different inferences were made with regard to treatment efficacy under LCPMM vs. the commonly used standard group-clustered latent growth model (LGM); coupled with other preliminary findings in this area, inferences from LGMs may be overly liberal when applied to data from rolling groups. Continued work on data analytic difficulties in groups with membership turnover is critical for furthering the ecological validity of research on behavioral treatments. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

���������Ʊ�ը����ֵģ��

可燃气体在运输、储存、加工和使用过程中，因可燃气体泄漏而形成的气云爆炸事故，常常会造成巨大的人员伤亡和财产损失。研究气云爆炸的特性和威力，可防范事故，减小损失。中采用有限差分方法编制了求解可燃气云爆炸过程的定解方程的数值模拟程序。方程组中的源项由能量均匀加入法处理，爆炸场中的间断问题通过人工黏性模型处理。经开敞空间乙炔——空气气云爆炸实验结果检验，数值计算结果的偏差在13％以内。计算结果表明，气云半径越大，爆炸最大压力和压力增加速率越大；气云爆热越大，爆炸最大压力和压力增加速率越大。     

CSP连铸机大型液压缸的故障分析与改进

论述引进德国SMS连铸机大包托臂液压缸存在的寿命短问题，分析设计制造缺陷．通过增大缸头密封支持面、(φ600)内圆孔倒角、再增加一道软支撑环、缸头导向部分开润滑槽、改进球杆的润滑流道、柱塞杆整体淬火等措施，消除了原来的问题．同时分析了此项改进的技术经济效果．     

屏蔽电泵运行中存在问题的分析与改进

对屏蔽电泵在非设计流量下工作存在较大的轴向力不平衡，造成前端轴承磨损严重进行了分析。在不降低效率的情况下，在屏蔽电泵的泵头加入平衡盘使轴向力得到平衡，并取得了满意的效果。