惯性平台系统误差的自补偿

提高惯性平台使用精度的途径之一是和计算机实时补偿平台误差的系统分量。首先介绍了仪表和平台误差模型，重点讨论如何从３个含有测量误差，安装误差和基准漂移误差的加速度计输出信号中，分离出载体飞行加速沿制导坐标系三轴的分量。对由于惯性基准的漂移而上起的载体姿态角的测量误差也进行了分析。     

Gasification reactivity of charcoal with CO2. Part I: Conversion and structural phenomena

The gasification reaction of fir charcoal with CO₂ was studied by isothermal thermogravimetric analysis under kinetic control. The derived reaction rate (r=dX/dt) as a function of the converted carbon mass (X) was compared with random pore model predictions and found to be much higher at elevated conversion levels than predicted by theory. Similar enhanced reaction rate behaviour was evidenced after removing the natural alkali catalyst from the charcoal by acid washing, suggesting that with untreated charcoal the late reaction rate contribution stems from both, catalytic and additional structure effects. Literature attributes the unpredicted late reaction rate behaviour to the disintegration of the porous char particle into small fragments, which, in line with percolation theory predictions, seems to occur only after a critical conversion level has been reached. However, our gasification data reveal a gradual rise in the charcoal reactivity thereafter, suggesting a breaking up (embrittlement) of the solid phase accompanied by the exposure of fresh surface area from fracturing. The original random pore model derivation given by Bhatia and Perlmutter is extended to account also for these peculiarities and the resulting kinetic relation described our reaction rate data well over the entire conversion range.     

预报复合材料热膨胀系数的细观力学模型

建立了一国观力学模型用于预报复合材料的有效热膨胀第数。利用这一模型计算热膨胀系数无需对复合材料进行热应力分析，仅需知道在某一相关外力场作用下，其组分的内部的平均应力场问题即可解决。     

调节对象参数和运动特性随工况变化的分析

水轮机调节对象的许多参数都是随运行工况变化的。以调节对象线性化模型为基础，从1个实例计算人手，计算了不同工况下水轮机传递系数和发电机6个参数的变化情况，进而计算这些参数变化对捌节对象特征根的影响。通过汁算表明，其水力振荡衰减速度与出力有关．而系统的其他运动特性随工况变化较小。     

三峡蓄水初期水库近坝区水环境特性分析

通过现场观测和数值模拟的方法，对三峡水库近坝区在蓄水初期的水流和水环境特性进行了 分析。对蓄水初期的溶解氧、BOD、COD和NH3-N、Cu等水质参数进行了观测，将蓄水初期水质资料与蓄水之前的结果进行了对比，分析了近坝区水环境变化趋势。采用大涡模拟紊流模型，考虑水体表面的热交换，对三峡近坝区的流动和水温分布特性进行了模拟。研究结果表明，三峡水库蓄水初期近坝区水流特性明显改变，主要表现为水深增加、流速变缓，部分地段有回流区出现。水质指标变化不明显，坝前断面溶解氧浓度、悬浮物浓度有所降低，和悬浮物密切相关的污染物总磷、重金属也随之降低；蓄水初期139m水位时坝前水域尚没有出现温度分层现象。     

超低硫燃料柴油的润滑性研究与性能研究

研究提出了超低硫燃料暂定战术技术指标，并规定了其润滑性要求。通过对基础油生产工艺研究、柴油润滑性添加剂研究及配方性能评定，成功研制了一种环保型超低硫燃料，满足外燃发动机（燃烧室高温高压）的使用要求。研制产品具有馏分窄、闪点高、氧化安定性好、低温性能优异、硫含量超低、润滑性能好等特点。燃料的低硫化是燃料发展的必然趋势。在我国开展低硫或超低硫环保型燃料研制，同时开展燃料润滑性添加剂的研制，具有重要意义。     

Engset multi‐rate state‐dependent loss models with QoS guarantee

We consider a single link loss system of quasi‐random input, described by the Engset multirate loss model (EnMLM). Blocked calls may once reattempt to be connected to the system requiring less bandwidth; then the system is described by the single retry model for finite sources (f‐SRM). The EnMLM and the f‐SRM are extended with the single threshold finite source model (f‐STM), where calls may attempt to be connected to the system with less bandwidth requirements, according to the link occupancy, before blocking occurs. We focus on CBP equalization in the EnMLM, f‐SRM and f‐STM, under the bandwidth reservation (BR) policy. For this analysis, we apply two approximate methods, the Roberts' method and the method of reverse transition rates (RTR), which lead to a recursive CBP calculation. We evaluate the accuracy of the above models under the BR policy by comparing the analytical with simulation CBP results, based on the relative approximation errors (RAE). The results are highly satisfactory because they show that the proposed models (formulas) lead to small RAE. Copyright © 2005 John Wiley & Sons, Ltd.     

新型废水厌氧处理工艺——内循环厌氧反应器

介绍内循环(IC)厌氧反应器的发展、基本结构、运行机理。分析该反应器的工艺过程,指出该工艺具有处理效率高、抗冲击能力强等优点。针对IC反应器存在的缺陷,人们对该反应器进行技术改进:通过提高它的内循环的气量进行处理低浓度有机废水;增加外循环装置缩短IC反应器的启动周期。     

文昌13-1-A9井酸化后含水上升分析及预测

文昌13-1-A9井酸化后综合含水达到54%,综合地质资料和油藏生产动态分析认为,导致文昌13-1-A9井酸化后含水上升加快的主要因素有:油水边界上升加快;酸化后渗透率提高,使油层与水体连通能力增强,加剧了边水的突进速度;酸化后采液指数提高,压降增大,导致底水锥进;油井位于油水过渡带内。在分析含水上升原因的基础上利用logistic模型对含水进行了预测,预测结果认为到2008年含水将达到80%以上。     

Determining the characteristics of systems with multiple inputs and multiple outputs

A simple and computationally efficient method of determining the transfer function and other characteristics of systems with multiple inputs and multiple outputs (MIMO systems) described by autoregression equations is proposed. The method is based on the use of the discrete Fourier transformation. The algorithm is highly suitable for computer implementation. The efficiency and simplicity of the method are illustrated using the example of a system with three inputs and three outputs. The proposed concept may be applied to systems described by the autoregression sliding mean.