Fatigue life calculation by means of the cycle counting and spectral methods under multiaxial random loading

The paper contains a new algorithm for estimation of fatigue life in HCF regime under multiaxial random loading using spectral methods. Loading of Gaussian distribution and narrow‐ and broad‐band frequency spectra were assumed. Various characteristic states of multiaxial loading were considered. The equivalent stress history was determined with use of the failure criteria of multiaxial fatigue based on the critical plane. For determination of the critical plane position, the method of variance was applied. During simulation, the authors compared the results obtained by a spectral method in the frequency domain with those from the rain‐flow algorithm in the time domain. The paper also contains the results of fatigue tests for 18G2A structural steel subjected to bending and combined bending with torsion. The tests were performed in order to verify the proposed algorithms for determination of fatigue life. It has been shown that under multiaxial random loading results of fatigue life calculated according to the considered algorithms in frequency and time domains are well correlated with the results of experiments.     

钢丝圈的失效分析

对72B纺织用钢丝圈进行失效分析，发现钢丝圈使用性能不合格的主要原因是热处理炉仪表指示温度偏差太大及热处理工艺规范不合理，使得球化退火后的金相组织出现粗晶铁素体，淬火和回火后的金相组织出现铁素体、粒状渗碳体，使材料塑性增加，满足不了使用性能。     

室内移动机器人超声传感器导航网络分布研究

对于室内广域移动机器人,超声波传感器网络是能够保证给定导航准确度的一种有效方法。合理的超声波传感器网络分布是实现超声波网络导航的重要条件。论述了超声波网络合理分布的原则,据此提出并分析了获得合理超声波传感器网络分布的四个步骤,仿真试验结果验证了它的有效性。     

A single chip multi-channel surface plasmon resonance imaging system

A single chip, multi-channel surface plasmon resonance (SPR) imaging system has been developed. The equipment has no moving parts and uses a single sensor chip on which multiple channels can be incorporated. A light emitting diode is used as a photon source while a CCD camera forms the detector. The optical configuration has been designed to achieve a uniform illumination of the sample over a fixed area with a range of incident angles. A calibration test using sucrose solutions shows that the sensitivity of the equipment is 4.3×10⁻⁴ refractive index units per pixel line-pair. The use of the system for simultaneous interrogation of different polyelectrolyte thin films, formed by the electrostatic layer-by-layer deposition method, is demonstrated. A reversible pH-dependent response for these organic layers is also reported.     

集控值班员如何正确处理电气设备故障

针对变电站实现无人值守后，如何远距离正确处理电气设备事故进行了分析，有利于提高集控值班员综合分析判断事故的能力。     

基于神经元网络的燃油锅炉烟气氧含量的软

针对目前各种氧含量检测仪表在运行过程中的可靠性差、使用寿命短及价格昂贵等诸多不足，通过探寻锅炉运行中的其他参数与烟气氧含量的映射关系，建立ＢＰ神经元网络，提出了燃油锅炉烟气氧含量的软测量方法。结果表明，其精度完全达到了设计要求。     

采用 AD590 集成温度传感器测温

集成温度传感器是两端式恒流器件具有标准化输出。采用ＡＤ５９０集成温度传感器进行温度测量。测量精度高，测温范围宽而且容易实现。因为ＡＤ５９０是恒流器件，所以适合远距离传送，也容易实现智能数字化显示     

混凝土构件火灾后损伤程度鉴定和加固

通过实际工程的调查和对砼材料在不同受火情况的试验研究，论证了采用外部特征综合分析并配合回弹试验等是判断砼构件火损程度的简便而实用的方法。     

Monitoring of multivariable dynamic processes and sensor auditing

Industrial continuous processes are usually operated under closed-loop control, yielding process measurements that are autocorrelated, cross correlated, and collinear. A statistical process monitoring (SPM) method based on state variables is introduced to monitor such processes. The statistical model that describes the in-control variability is based on a canonical variate (CV) state space model. The CV state variables are linear combinations of the past process measurements which explain the variability of the future measurements the most, and they are regarded as the principal dynamic dimensions. A T² statistic based on the CV state variables is utilized for developing the SPM procedure. The CV state variables are also used for monitoring sensor reliability. An experimental application to a high temperature short time (HTST) pasteurization process illustrates the proposed methodology.     

井下粉尘多参数检测的自适应方法

为提高井下粉尘计重含量检测精度并同时获得粒度分布参数,根据井下粉尘衍射光的角谱特征,提出了一种适合于在单片机上运行的算法。首先将衍射光角谱归一化,使得不同浓度但粒度分布相同的尘样具有相同的归一化角谱,而该角谱与给定模式的角谱的贴近程度则用差值平方和表征。由几个优选模式求得的计重含量或粒度分布取加权平均即可获得待求参数。考虑到现场环境中噪声抑制能力和对尘样多样性的适应能力至关重要,本文中最后给出了针对这两个方面的仿真实验结果。