Off-Optimum Cure of Aerospace Epoxy Adhesives

Four epoxy film adhesives used in aircraft manufacture and repair have been examined to establish the effect of deviation from the cure cycle specified by the manufacturer. In addition to the variation of the cure cycle, two surface preparations of the aluminium adherends (chromic acid etch or grit blast followed by silane treatment) were evaluated. Thermal analysis was used to examine the cure envelope of the adhesive, and its extent of cure and glass transition temperature. The adhesive properties were assessed by shear strength (in both single lap joints and in Iosipescu configuration), durability (Boeing wedge test) and chemical resistance to selected aggressive fluids. The sensitivity of the performance of a particular adhesive to offoptimum cure conditions depends on its composition and needs to be determined, not predicted.     

Residual Stress Evolution in Repair Welds

Abstract: The aim of this paper is to study the influence of the repair procedure on the evolution of residual stress distribution in butt welds. C-Mn steel coupon plates of 11 mm thickness were prepared, subjected to stress relief heat treatment and welded with two beads, using the gas metal arc welding process. After the deposition of two weld beads, two successive repair welds were made on the middle length of the second bead. Longitudinal and transverse residual stresses were measured in the vicinity of the weld, after deposition of the two weld beads and after each repair weld. Residual stress evaluation was conducted using an X-ray diffraction method. The repair welds caused a decrease in magnitude of the initial longitudinal residual welding stresses, and an increase of the transverse residual stress magnitude, in tension at points within the repair length, and in compression at points outside the repair length.     

转子叶片在非均匀来流条件下的流体激振特性

该文通过研究得出非均匀来流对转子叶片流体激振的三个重要特征 :非均匀来流相对于转子叶片的非定常流中主频分量是产生叶片动应力的决定因素 ;非均匀来流的非均匀度 (相当于非定常流的波幅 )大小和叶片流体激振的动应力大小成正比 ;转子叶片流体的定常压力水平与叶片动应力的水平密切相关。图 4表 2     

固井水泥环缺陷对套管强度影响仿真分析

固井水泥环质量对套管的强度影响很大。建立了水泥环缺少1／12的井筒平面应变有限元模型，通过对固井水泥环缺陷引起的套管应力变化进行仿真模拟分析，得出无内压下套管的最大径向位移是水泥环完整时的3．9倍，水泥环的缺少导致Mises应力集中系数为2．0，套管外壁的最大塑性应变达到0．0152，定量分析固井质量对套管强度的影响，为热采井套管损坏提供一些定量数据。     

复合地基中优化设计参数的方法

本文给出了复合地基应力比置换率设计的优化方法,讨论了复合地基中应力比的基本概念和影响因素,可供工程应用时参考。     

Calculation of fatigue limits of case-hardened specimens with consideration of mean stresses and residual stresses

 The strength of case-hardened parts under cyclic loading can be determined in an experimental manner, but this can produce a large amount of costs due to the expenditure of material and testing time. Therefore, a calculation method is developed, that strongly reduces the number of experiments. The presented model is based on Weibull's weakest-link concept and allows to compute the survival probability of a case-hardened part which is loaded close to the fatigue limit. The essential quantities in this model are the distribution of Vicker's hardness of the material, the exponents of the Weibull distribution of the volume and the surface, the residual stress state, the surface roughness and the surface oxidation depth. By integrating the survival probabilities of the surface and the volume, the survival probability of the entire specimen or part can be calculated, which allows to compute the fatigue limit. The necessary parameters have to be determined from reference specimens. The model is successfully examined by comparing experimental and calculated results of smooth and notched case-hardened specimens under alternating torsion, rotating bending, repeated tension and tension-compression. Received 20 August 2001 / Accepted 11 November 2001     

不规则I型和L型横截面形状薄壁杆件的横向弯曲稳定分析

根据势能驻值原理,采用转换B3样条函数模拟杆件横截面的翘曲位移场,文[8]提出了用于分析在横向荷载作用下薄壁杆件稳定问题的样条有限杆元法。方法适用于任意横截面形状和任意边界条件的薄壁杆件,考虑了杆壁中面上剪切变形的影响,能很好地描述剪力滞后现象。本文讨论了不规则I型截面简支梁和L型截面简支梁的屈曲分析,数值算例的结果表明了方法的灵活性、精确性和有效性。