NiCuZn铁氧体和银内电极的共烧行为

NiCuZn铁氧体正作为磁介质广泛地应用于低烧多层片式电感，因此有必要对其与银内电极的共烧行为进行研究。该文主要介绍NiCuZn铁氧体／银内电极多层复合体共烧过程中的烧结收缩、界面反应、扩散对介质性能的影响。尖晶石结构中存在相当数量的空位，这为银离子提供了一定的溶解度，因此在共烧过程中银对铁氧体的相组成影响较小。银对铁氧体性能的影响体现在两个方面。一方面是由于银具有相对低的烧结温度，从而在烧结过程中起到助烧剂的作用，促进致密化过程，提高烧结体的密度和磁导率；另一方面，银促使铁氧体中的铜在晶界处析出，导致晶界处应力，使磁导率降低，晶粒生长也被一定程度地抑制。     

含腐蚀凹坑尿素合成塔的安全评定与分析

对尿素合成塔上封头腐蚀凹坑采用中国SAPV-95和美国API579规范分别进行安全评定，给出安全裕度，简略分析安全评定的结果。     

湿H2S环境中金属材料腐蚀的研究

介绍了在湿H2S环境中金属材料的腐蚀试验标准、方法和手段并重点强调了在H2S试验过程中常遇到的一些问题的处理方法.最后,指出了应加强H2S腐蚀的基础性和系统性研究的研究方向.     

The rate of corrosion of concrete reinforcement and possibilities of its mathematical modelling

The paper describes a method for the mathematical modelling of steel reinforcement corrosion rate. This method is based exclusively on experimental results and expression of the influence of significant corrosion factors in the form of functional relations. The method takes into account the reality of the effects of corrosion factors, their contigency and complexity, and various circumstances occurring in practice. It represents one way towards the development of methods for the prediction of service life of reinforced concrete and structures.     

高强度钢的Zn—Ti合金新镀层

本文研究了一种Ｚｎ－Ｔｉ合金新镀层，经盐水浸泡、中性盐雾和大气暴露试验结果试验，其耐蚀明显超过镀Ｚｎ层，并与镀Ｃｄ层相近，用缺口持久拉伸试验检验氢脆性，拉伸持续时间超过２００ｈ，达到原航空部部颁标准（ＨＢ５０６７－８５），该镀层适用于高强度钢防护。     

Electrosynthesis and impedance studies on zinc selenide

Electrochemical impedance measurements have been used to characterize zinc selenide films prepared by electrochemical co-deposition at a platinum rotating disk electrode. Estimations of capacitance and polarization resistance of variously prepared electrodeposits have been carried out to determine charge carrier density and corrosion rates.     

The influence of NaCl and CO2 on the atmospheric corrosion of magnesium alloy AZ91

The influence of NaCl and CO₂ on the atmospheric corrosion of magnesium alloy AZ91 is studied in the laboratory. Samples were exposed under carefully controlled air and flow conditions; the relative humidity was 95%, the temperature was 22.0°C and the concentration of CO₂ was < 1 ppm or 350 ppm. Different amounts of sodium chloride (0–70 μg/cm²) were added before exposure. The corrosion products were analyzed by gravimetry, ion chromatography, X‐ray diffraction and scanning electron microscopy. Mass gain and metal loss results are reported. The combination of high humidity and NaCl is very corrosive towards AZ91. However, the NaCl‐induced corrosion is inhibited by ambient concentrations of CO₂. Exposure in the absence of CO₂ gives rise to heavy pitting, with brucite, Mg(OH)₂, being the dominant corrosion product. In the presence of CO₂ a layer of hydrated magnesium hydroxy carbonate, Mg₅(CO₃)₄(OH)₂ · 5 H₂O forms. A tentative corrosion mechanism is presented that explains the behavior in the two environments.     

A3钢的工业大气腐蚀

在辽宁省工业城市进行 A3钢大气暴露试验。两年后测出不同地点腐蚀率。依据所记录的各试验点的气象数据和污染数据,讨论了 A3钢的大气腐蚀规律。     

离子注入对铁及其低合金、铝及其合金耐腐蚀性能的影响

离子注入对金属腐蚀行为的研究已达30年．研究结果表明离子注入对改变金属表面成分和表面性能是极为有效的技术．本文概述了离子注入对铁及其低合金、铝及其合金的腐蚀电化学行为的影响．涉及的注入离子达十余种。     

Preparation of core–shell structured alumina–polyaniline particles and their application for corrosion protection

Polyaniline (PANI) was synthesized by chemical oxidative polymerization of aniline (ANI) in the presence of alumina (Al₂O₃) particles. The polymerization of ANI occurred preferentially on the surfaces of the particles, resulting core–shell structured alumina–polyaniline (Al₂O₃‐PANI) particles. Morphology examination showed that with decreasing of the weight ratio of Al₂O₃/ANI in the reactants, the thickness of the PANI layer increased and changed from an even surface morphology to a particulate morphology. UV–vis and Fourier transformed infrared (FTIR) spectra indicated that there is no chemical interaction between the PANI layer and the Al₂O₃ surfaces. The PANI layer adhered well to the particles and can be used as anticorrosive fillers for polymer coatings. Enhanced corrosion protection performance was achieved for the emeraldine base (EB) form of PANI deposited Al₂O₃ particles (Al₂O₃‐EB) filled epoxy coating on carbon steel in 3.0 wt % aqueous NaCl solution. The particles demonstrate both excellent corrosion protection performance and lower cost, which will be of great importance in practical applications. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4372–4377, 2006