掺(Ga,Si)银铝浆对n型TOPCon太阳能电池电性能的影响

银铝浆是新一代太阳能电池(n型TOPCon)的关键材料,但其金属化后在Si发射极表面形成很大且很深的“银铝尖钉”,尖钉易击穿p-n结造成短路,成为限制其应用的瓶颈。引入Si、Ga元素对银铝浆进行优化,分别制备了掺Si和掺Ga, Si的银铝浆,研究其对金属化区域暗态饱和电流密度J_0.metal、欧姆接触电阻R_c的影响机制。结果表明：掺入少量Si后,金属化区域未见明显“银铝尖钉”,说明掺Si后抑制了在浆料金属化时出现“银铝尖钉”的现象,对p-n结损伤较小,J_0.metal下降,开路电压V_oc上升,但是R_c增大。再掺入Ga组分后“银铝尖钉”明显变浅,数量变多,R_c下降,弥补了掺Si银铝浆欧姆接触差的弊端,有较高的电池转换效率;用扩散浓度测试仪(ECV)对发射极表层进行元素浓度分析,发现Ga分布于表层0～50 nm处,有利于改善欧姆接触。研究了Ga、Si的掺入量对银铝浆电性能的影响,电池转换效率最高达到24.68%,太阳能电池效率提升0.55%。     

Modification of Iron with Degradable Silver Phases Processed via Laser Beam Melting for Implants with Adapted Degradation Rate

In medical technology, implants are used to improve the quality of patients’ lives. The development of materials with adapted properties can further increase the benefit of implants. If implants are only needed temporarily, biodegradable materials are beneficial. In this context, iron-based materials are promising due to their biocompatibility and mechanical properties, but the degradation rate needs to be accelerated. Apart from alloying, the creation of noble phases to cause anodic dissolution of the iron-based matrix is promising. Due to its high electrochemical potential, immiscibility with iron, biocompatibility, and antibacterial properties, silver is suited for the creation of such phases. A suitable technology for processing immiscible material combinations is powder-bed-based procedure like laser beam melting. This procedure offers short exposure times to high temperatures and therefore a limited time for diffusion of alloying elements. As the silver phases remain after the dissolution of the iron matrix, a modification is needed to ensure their degradability. Following this strategy, pure iron with 5 wt% of a degradable silver–calcium–lanthanum alloy is processed via laser beam melting. Investigation of the microstructure yields achievement of the intended microstructure and long-term degradation tests indicates an impact on the degradation, but no increased degradation rate.     

Preparation of Porous Silver Nanowires-Melamine Formaldehyde Hybrid Composite Materials and Their Electromagnetic Shielding and Flame-Retardant Properties

Along with the booming development of communication technology and electronic equipment, higher requirements of flame-retardant and EMI shielding performances for electromagnetic interference (EMI) shielding materials are put forward. Herein, the ultralight and porous silver nanowires (AgNWs)-melamine formaldehyde (MF) hybrid composite with unique micro-/nanostructure is developed by a facile dip-coating method, which uses the AgNWs as 1D conductive coating and MF foam (MF foam) as 3D skeleton template. Benefiting from the unique porous micro-/nanostructure, the resultant hybrid composite displays low density, excellent EMI shielding performances, and superior flame-retardant property. The EMI shielding effectiveness (SE) and specific EMI SE (SSEt) of the hybrid composite in X-band (8.2–12.4 GHz) can be up to 77 dB and 26971.4 dB cm⁻² g⁻¹, respectively. At the same time, the hybrid composite also passes the vertical burning test and shows an increased LOI value of 40.6%. The combination of flame-retardant and EMI shielding performances for EMI shielding materials makes the AgNWs-MF hybrid composite great application potential in civil and military fields. This work provides a new guide for the design of multifunctional high-performance EMI shielding materials.     

Production of perovskite-like La1−xCaxMnO3+δ ferromagnetic thin films by electrochemical reduction

Ferromagnetic and perovskite-like thin films (<1m) of La1–xCaxMnO3+ have been routinely prepared by heat treatment of an amorphous La–Ca–Mn precursor. The precursor was electrodeposited cathodically in the absence of oxygen and water onto polished silver substrates from a nonaqueous solution of the components' nitrates. Analysis by X-ray diffraction and SQUID magnetometry shows these materials exhibit the appropriate structural and magnetic phases indicative of colossal magnetoresistance.     

Gold nanowire array electrode for non-enzymatic voltammetric and amperometric glucose detection

The non-enzymatic voltammetric and amperometric detection of glucose using a gold nanowire array electrode is described. The voltammetric detection of glucose was performed by cyclic and differential-pulse voltammetry. The detection of glucose by partial and direct oxidation of glucose during the anodic and cathodic potential sweeps was shown in cyclic voltammetry. An unusual decrease in overpotential for partial oxidation of glucose on a Au NW array electrode was observed. A linear differential-pulse voltammetric response for partial oxidation of glucose was observed up to a glucose concentration of at least 20 mM with a sensitivity of 41.9 μA mM⁻¹ cm⁻² and detection limit below 30 μM (signal-to-noise ratio of 3) for glucose oxidation at low potentials, where the influence of possible intermediates can be avoided. The amperometric response was also linear up to a glucose concentration of 10 mM with a sensitivity of 309.0 μA mM⁻¹ cm⁻². The wide dynamic range and high sensitivity, selectivity and stability, as well as good biocompatibility of the Au NW electrode make it promising for the fabrication of non-enzymatic glucose sensors.     

广西镇龙山金（银）矿的构造控制特征

本文阐述了广西镇龙山金（银）矿化集中区内主要断裂构造的基本特征,并指出,其中规模较大的,与矿化关系较密切的主要是近ＥＷ向,次为近ＳＮ向断裂,它们组合成线状,交叉状和放射状断裂带,并严格控制着区内岩浆岩、矿化带、矿脉、矿体和“富矿包“的空间展布。这对找矿评价和预测盲矿体都具有实际意义。     

Thermopower ofAg_{2 + \delta } S across theα-β transitionacross theα-β transition

Thermopower data of S in both of itsα- andβ-phases are reported and the results are compared with the data on Se. Communication No. 129 from the Solid State and Structural Chemistry Unit.     

超声处理对鲢鱼肉肌原纤维蛋白性质的影响

以鲢鱼为原料,研究了超声处理对鲢鱼肉肌原纤维蛋白性质的影响．结果表明：经超声处理后,肌原纤维蛋白的溶解度、起泡性及泡沫稳定性、乳化性及乳化稳定性、热稳定性均随超声时间的延长先提高后下降,且随超声频率的增大而提高．超声处理15min后,与未经超声处理的蛋白相比,80kHz作用下的蛋白溶解度提高了37．59％,起泡性和泡沫稳定性分别提高了59．16％和56．09％,乳化性和乳化稳定性分别提高了51．11％和53．84％,热稳定性提高了32．59％．经超声处理后,鲢鱼肉肌原纤维蛋白的性质可以得到有效的改善．     

银纳米线的制备及其对电化学发光催化研究

采用水热法,在反应体系中加入微量的CuCl2作为去氧剂,以AgNO3为前驱物,聚乙烯吡咯烷酮(PVP)为稳定剂和结构导向剂,乙二醇为还原剂和溶剂制备银纳米线.研究了反应温度、反应时间及CuCl2浓度对产物微观形貌的影响.通过X-射线衍射(XRD)、扫描电子显微镜(SEM)等检测手段表征了其结构和性能.同时,将所制得的银纳米线作为联吡啶钌[Ru(bpy)2+3]电化学发光(ECL)的工作电极对其催化机理进行研究.结果表明:在反应温度为165℃、反应时间为1h、CuCl2浓度为4 mmol/L时制备出了具有面心立方结构的,长度为13 μm,长径比约为75的银纳米线;与普通银丝电极相比,由于具有较高的比表面积和较独特的催化特性,银纳米线电极更适合作为Ru(bpy)2+3 ECL的工作电极.     

C3H6选择性催化还原NO催化剂Ag／γ—A12O3的研究

采用低负载量的(0～3％)Ag／γ-A12O3体系作为C3H6选择性催化还原(C3H3-SCR)NO的催化剂，考察了银负载量、反应温度、空速对NO转化率的影响．同时对于原料气中氧的作用进行了研究．结果表明：银负载量为1．5％时，催化剂表现出最高的反应活性；在考察的条件范围内，原料气中含氧对NO的还原有促进作用，适宜的氧浓度为0．27％；反应温度的过高会导致还原气中C3H6大幅度转化为CO2。