Homogenization of hardness distribution and distortion in high pressure gas quenching

Quenching with gases rather than oil or other liquid media has the advantages of reducing the risks concerning health and environment, while simultaneously homogenizing the quenching results and minimizing distortion due to a wide range of possible process parameter variations and the pure convective heat transfer. In this contribution, a coupled solution for increasing homogenization of quenching results within high pressure gas quenching will be presented. In the first stage, an experimental test facility was set up for flow investigations and in the second stage a numerical simulation model was generated. The numerical and experimental results of the flow through the chamber were compared for several boundary conditions. Finally, after complete verification of the simulation, the model may be used to assist in parameter variation for optimization of homogeneous high pressure gas quenching.     

Using rainbow net simulation to measure fault tolerance in a multiprocessor

The Rainbow net simulation technique is applied to modelling the impact of system load and fault handling on the availability of a fault-tolerant multiprocessor architecture. Rainbow nets are described along with the motivation for creating this modelling technique. A Rainbow net fault-handling model is created for the fault-tolerant multiprocessor architecture and the topology is shown to remain constant in size, independent of the number of processor, memory and I/O elements configured in the system. Simulation is performed with a varying load in terms of the number of active jobs the system must support. Results are given showing how the fault-tolerant capability varies with load. Two new metrics for evaluating fault tolerance are introduced; namely full fault-tolerability and partial fault-tolerability. They are based on simple observations in the model.     

PCR芯片和生化微分析系统

介绍了PCR微芯片的最新研究进展,给出了不同结构的PCR芯片设计原理以及特点,介绍由PCR芯片为主要单元的集成微全分析系统的相关研究,同时简要介绍了对PCR的仿真模拟等。     

A probabilistic simulator for population dynamics of quasispecies

We constructed a probabilistic simulator that allows all the events in population dynamics such as death, birth, mutation, and suppression/stimulation to be described by probabilistic rules. The simulator also facilitates a lattice used for expressing distribution and diversity (number of distinct strains) of quasispecies. The simulator is used to investigate the diversity threshold in HIV and T-cell interaction. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008     

Pulsating Jet Impingement Heat Transfer Enhancement

This article presents results from a numerical study of pulsating jet impingement heat transfer. The motivation is to seek conditions offering a significant enhancement compared to steady flow impingement drying. The CFD software package FLUENT was used for simulating slot-type pulsating jet impingement flows with confinement. The parameter study included velocity amplitude ratio, mean jet velocity, and pulsation frequency. The distance from nozzle exit to surface was three times the hydraulic diameter of the nozzle. The Reynolds number based on the nozzle hydraulic diameter and jet temperature was 2,460 with a mean jet velocity of 30 m/s, which is the base case of the numerical experiments. Results showed that time-averaged surface heat transfer increased with increasing velocity amplitude for the same mean jet velocity. Large velocity amplitudes helped enhance heat transfer by two mechanisms: high jet velocity during the positive cycle and strong recirculating flows during the negative cycle. For the cases with different mean jet velocities but the same maximum velocity, time-averaged surface heat flux decreased with decreasing mean jet velocity. As for the effects of pulsation frequency, with high-velocity amplitude ratio, time-averaged surface heat fluxes were at the same level regardless of frequency. However, at low-velocity amplitude ratio, high frequency caused stronger recirculating flows resulting in greater heat transfer compared to the cases with a lower frequency.     

利用计算机进行油气资源评价和勘探决策

本文着重介绍了构成《现代勘探决策理论系统》的5个主要计算机模块,即:生油岩热演化处理、求任意曲边形面积、数学模拟预测资源量、勘探经济评价分析及决策、辅助处理等模块。该系统曾在塔里木盆地和准噶尔盆地的油气资源评价和勘探决策中发挥了作用,受到了专家和用户的好评。     

Effect of the particle size ratio on the conductivity of conductor-insulator powder composites: Numerical simulation

A theoretical method for determining the percolation limit and effective conductivity of composites based on polydisperse mixtures of insulator and conductor powders is proposed. The effect of the particle size ratio between the insulator and conductor on the percolation limit and effective conductivity is studied. Numerical simulation of the microstructure, effective properties, and percolation limit in composites is discussed. __________ Translated from Poroshkovaya Metallurgiya, Vol. 46, No. 1–2(453), pp. 31–40, 2007.     

Numerical Simulation of Deforming Manufacture Process for Automobile Bevel Gear Blank

1 Introduction Rear axle bevel gearis a vital kind of annular accessory with high precision and hugeload availablefeatures ,andit is widely used as the differential drive in automobiles and tractor .In China ,the traditional manufactureapproach of producing the rear axle bevel gear blankis die forging,which not only requires a highinvestment ofproduct equipments , but also involves a low material utilization and great noise .In order to overcome thesedrawbacks , manyresearchers have done a gre…     

基于VC＋＋的仿真训练系统编程

给出了以PCI-I64IOT型I/O卡为核心的硬件接口电路和软件设计思想,详细分析了编程方法。实践表明,利用该系统能完全实现侦察专业的全部训练科目,满足部队和院校训练的需要。     

Building a right digital twin with model engineering

In recent years, the concept of digital twin (DT) is attracting more and more attention from researchers and engineers. But there is still no consensus on what a right DT is. On one hand, some common models are renamed as DTs. On the other hand, some DTs extremely pursue ‘the same’ as physical objects, which bring unnecessary complexities to them. In this paper, we try to answer two questions from the point of view of model engineering: how to define a right digital twin, and how to build a right digital twin. The concept and related technologies of model engineering are introduced. Some basic principles and a set of metrics for a right DT are given. An evolutionary concurrent modeling method for DT (ECoM4DT) is proposed not only inheriting the theory from classic M&S methods but also highlighting the characteristics of DT compared with traditional models to systemically guide the DT modeling process.