中频炉酸性炉衬使用寿命的探讨

通过对炉衬材料的选择,作用机理及影响石英砂炉衬材料寿命的相关因素的阐述,说明了SD-T-A石英砂干振料可提高中频炉酸性炉衬使用寿命的原因.     

纳米W-Cu粉末的均相沉淀法制备及其烧结性能

采用湿化学工艺--蒸氨均相沉淀法,制备了纳米CuWO4·2H2O/Cu2WO4(OH)2均相沉淀物,然后煅烧、还原,得到含Cu 30%的W-Cu复合粉.将该复合粉压坯在H2气氛中于不同温度下烧结后,对烧结体的微结构和物理、力学性能等进行了测试分析.实验结果表明:蒸氨均相沉淀法制备的W-Cu复合粉体具有纳米粒度和均匀的化学组成,其烧结活性高,在较低温度下烧结即可达很高的致密化程度.由上述W-Cu粉体所制备的烧结体具有良好的物理、力学性能.     

活性石灰/粉煤灰制备烧结烟气脱硫剂配比试验研究

本文研究了以钢铁企业常用物料活性石灰和自备电厂粉煤灰制备的脱硫剂,在循环流化床脱硫试验装置上进行了烧结烟气脱硫剂配比试验.试验结果表明,活性石灰与粉煤灰的质量比按1:2配置时,脱硫剂钙的利用率较高,具有较好的经济性.     

MIM Fe基合金的合金化强化

研究金属粉末注射成形铁基合金在强还原性氢气氛烧结条件下的合金化强化效果，结果表明，添加Ｃｕ、Ｎｉ、Ｍｏ等元素能取得显著的固溶强化效果，其中成分为Ｆｅ－２Ｎｉ－２Ｃｕ－０．４５Ｍｏ的机械性能达到σｂ＝４８３ＭＰａ，σｓ＝３４０ＭＰａ，δ＝９％和ＨＲＢ８３。     

Microstructures and properties of coating from cemented carbide by vacuum powder sintering

In this paper, the microstructures and properties of coating from cemented carbide of WC–Fe–Co–Ni on the substrate 45 steel are studied. The effects of sintering temperature on the microstructures of coating, the interface structures between coating and the substrate, the microhardness distribution and its wear resistance in the coating are investigated. The results indicate that the coating is strongly metallurgical bonded with the substrate by the mutual diffusion and penetration of Fe towards the coating and W, Co, Ni towards the substrate at sintering temperature ranging from 1280 °C to 1300 °C. The coating obtained exhibits compact structure and uniformly distribution of WC with fine grain and porosity free from defects, having high microhardness and preferable wear resistance.     

Laser-Sintered Barium Titanate

Laser sintering of alkoxy-derived ultrafine BaTiO₃ powders was investigated. The temperature increases of the sample with laser irradiation were measured with a thermocouple. It was found that laser irradiation could generate enough heat to sinter ceramics. A slurry was prepared by mixing an alkoxy-derived BaTiO₃ powder, binder additives, solvent, and plasticizer. The slurry was tape cast and dried to give a green sheet. The green sheet was laser sintered and was then characterized by SEM, XRD, and density measurements. The effect of burnout before laser irradiation and the characteristic microstructure of laser-sintered BaTiO₃ are described.     

Kinetics of the Initial Stage of Sintering from Shrinkage Data: Simultaneous Determination of Activation Energy and Kinetic Model from a Single Nonisothermal Experiment

A new method for the kinetic analysis of the initial stage of sintering for constant-heating-rate data has been proposed. Unlike all of the methods previously reported in the literature, this new method proposed here allows the simultaneous determination of the activation energy and the kinetic model from a single dilatometric curve recorded under a linear-heating-rate program. The proposed method has been tested with simulated sintering curves and experimental results have been obtained for the sintering of a rutile sample.     

Rapid Reactive Synthesis and Sintering of Submicron TiC/SiC Composites through Spark Plasma Sintering

Submicrometer TiC/SiC composites were fabricated by a rapid reactive sintering process through spark plasma sintering (SPS) technique using the carbon, titanium, and nanosized-SiC powders without any additive. It was found that the composite could be sintered in a relatively short time (8 min at 1480°C) to 97.9% of theoretical density. After sintering, the phase constituents and microstructures of the samples were analyzed by X-ray diffraction techniques and observed by scanning electron microscopy. The effect of nanosized and microsized SiC additives on the microstructure of TiC/SiC composites was investigated.     

六铝酸钙材料的合成及其显微结构研究

分别采用轻质碳酸钙和活性氧化铝 ,或纯铝酸钙水泥和活性氧化铝为初始原料 ,反应烧结合成了六铝酸钙 (CA6)材料 ,研究了原料和成型压力对合成材料的烧结性能和显微结构的影响 ,同时借助于XRD、TG -DSC、SEM和EDAX等测试手段对其反应过程、物相变化和显微结构进行了分析和观察。研究结果表明 :(1) 130 0℃时 ,合成材料的主晶相为刚玉相和CA2 ,并开始有CA6形成 ;温度升至14 0 0℃ ,CA6大量生成 ;15 0 0℃时反应完成 ,产物全部为CA6相。 130 0～ 15 0 0℃时 ,上述反应表现为体积膨胀过程 ,试样的体积密度和径向线收缩率随温度的变化不大 ;而高于 15 0 0℃时 ,试样明显趋向烧结 ,体积密度升高 ,线收缩率加大。采用纯铝酸钙水泥和活性氧化铝合成的试样的体积密度均高于采用轻质CaCO3 和活性氧化铝的 ,尤其在烧成温度高于 15 0 0℃时。坯体的成型压力对这两种合成试样的烧结性能均没有显著影响。 (2 )合成六铝酸钙材料的晶粒形貌与合成工艺有关 ,制备片状晶粒的六铝酸钙材料需满足两个条件 :一是晶核有足够的发育空间 ,二是从晶核生长形成片状结构需足够的物质扩散。采用纯铝酸钙水泥和活性氧化铝为原料的试样 ,其CA6晶核很容易发育成片状晶形 ,且随着坯体成型压力的增加 ,片状CA6有向等轴状发展的趋势 ;采用     

Sintering of Pt/Al2O3 reforming catalysts: EXAFS study of the behavior of metal particles under oxidizing atmosphere

The effect of an oxidative atmosphere (300 °C) is studied on fresh and sintered unchlorinated naphtha reforming catalysts containing 0.6–1% Pt. The TPR profiles show that only one species is formed using our experimental conditions, regardless of the mean crystallite size of the metal particles. The structural information supplied by EXAFS compared with cuboctahedral particle modeling, implies that such species is a surface platinum oxide, the structure of which is close to that of PtO₂, but largely distorted. This is true whether the catalyst is sintered or not.