The prediction of transport parameters in filamentous fermentation broths based on results obtained in pseudoplastic polymer solutions

Transport phenomena studies on single phase “model” fluids are of limited value in biochemical engineering if they cannot be translated to the heterogeneous systems encountered in real fermentation processes. In this paper we discuss the utility of polymer solutions as models of filamentous fermentation broths for evaluation of: pipeline friction factors and impeller power numbers (turbine and helical ribbon). To a first approximation, polymer solutions can serve as suitable models for the prediction of laminar flow pressure drop in pipelines and turbulent power consumption in stirred tanks. However, results obtained on polymer solutions do not directly apply to filamentous fermentation broths for predictions of laminar flow impeller power consumption and the transition point for turbulent flow in stirred tanks. These discrepancies are believed to result from the existence of a time dependent yield stress in filamentous fermentation broths.     

氢氧化铝微粉生产过程中晶种分解的研究

晶种分解是种分法生产氢氧化铝微粉的工序，介绍了控制铝酸钠精制液的分解温度、分解时间、搅拌强度等条件并添加特制的高活性晶种做晶种生产优质氢氧化铝微粉的生产过程，并通过对几个月的生产跟踪分析研究，得出氢氧化铝微粉的晶种分解主要与晶种的质量和数量、分解温度、分解时间及搅拌强度等因素有关，这对于进一步完善氢氧化铝微粉的生产工艺起到很大的作用。     

Pressure drop for single and two‐phase flow of non‐newtonian liquids in helical coils

New experimental results on pressure loss for the single and two‐phase gas‐liquid flow with non‐Newtonian liquids in helical coils are reported. For a constant value of the curvature ratio, the value of the helix angle of the coils is varied from 2.56° to 9.37°. For single phase flow, the effect of helix angle on pressure loss is found to be negligible in laminar flow regime but pressure loss increases with the increasing value of helix angle in turbulent flow conditions. On the other hand, for the two‐phase flow, the well‐known Lockhart‐Martinelli method correlates the present results for all values of helix angle (2.56‐9.37°) satisfactorily under turbulent/laminar and turbulent/turbulent conditions over the following ranges of variables as: 0.57 ≤ n′ ≤ 1; Re′ < 4000; Re_l < 4000; Re_g < 8000; 8 ≤ x ≤ 1000 and 0.2 ≤ De′ ≤ 1000.     

制约煤制合成氨装置长周期运行因素分析

从山化试生产经验，总结分析了制约煤制合成氨装置长周期稳定运行的因素，提出了今后技术改造方向。     

川中丘陵区地表干湿长程相关性及影响因素研究（研究生论坛）

为探究川中丘陵区干湿动态动力学机制,提供旱涝预测的理论依据。根据川中丘陵区8个气象站点1958~2013年逐日气象资料,采用Penman—Monteith 模型计算潜在蒸散量,构建出湿润指数。在此基础上,基于去趋势波动分析方法（DFA）,对逐月、分季节、极端干湿湿润指数进行长程相关性分析,并探讨了影响湿润指数长程相关性的气象因子。结果表明：除南充、遂宁外,其余地区逐月湿润指数变化长程相关,并非完全随机;分季节与极端干湿湿润指数均具有长程相关性;对于不同季节而言,长程相关性以夏季最强,秋、冬两季次之,春季最弱,对于极端气候而言,极端湿润长程相关性强于极端干旱;通过对湿润指数与气象因子长程相关性一致性分析,降水标度指数与湿润指数标度指数呈显著正相关。     

Effect of Mode of Drying on Microstructure of Potato

Potato v. Irga was subjected to blanching, and thereafter was dried by convection, puff-drying, and freeze-drying. Microstructure of raw, blanched, and dried tissue was analyzed under the light microscope using computer image analysis. It was found that the tissue of the investigated variety is built up from cells much smaller than those described in literature for other cultivars. Blanching caused starch gelatinization and increase of cross-sectional area of cells. There was no evidence of broken cell walls. Convective drying resulted in cell shrinkage and some breaking of cell walls. It was estimated that some 12% of cells lost integrity during drying. Limited disintegration of the tissue caused by convective drying is attributed to small size of cells, large contact area, and high cohesive forces between cells. Puff-drying damaged the tissue much more than the convective drying. The most devastating to tissue microstructure was freeze-drying, probably freezing per se.     

面向在线社区用户的群体推荐算法研究

结合现有两种主要群体推荐算法的优势, 建立新的算法框架, 并引入差异度因素对模型进行优化。另外, 考虑到在线社区用户的特点, 定义互动度指标来描述群体成员间的互动程度, 通过分析其与推荐精度之间的关系, 探讨互动度对群体推荐的影响。选取豆瓣网数据进行实验, 并与传统方法进行比较, 结果表明, 融入差异度的算法具有更好的推荐效果, 且有效的互动机制能够保证较高的推荐精度。     

开放水热法制备莫来石复相纳米晶体的影响因素

以天然高岭土为原料,经精细化处理煅烧制备莫来石.用常压、开放水热技术制备出莫来石复相纳米晶体材料.实验表明:常压、开放水热条件下制备莫来石复相纳米晶粉体的水热反应中,采用质量比为m(Na2O)/m(SiO2)=2.8,m(H2O)/m(Na2O)=35～30,0～80℃控温升温1 h,在80℃保温2 h,可制备出尺寸为80～100 nm莫来石复相纳米晶体.所制备的莫来石纳米晶体的水热溶液相变驱动力△μ为(3.609～4.672)×10-20 J/mol;水热体系溶解度控制在3.891×10-6 mol/L;熔解热△E为18.846 kJ/mol;晶体生长速率常数选择0.85～0.92,有利于快速成核和晶体生长,并且可以很好地控制晶体尺寸和分散度.     

基于集成温度传感器的硅微陀螺仪数字化温度补偿研究

提出了一种基于集成温度传感器的硅微陀螺仪数字化温度补偿方法。首先,介绍了集成温度传感器的硅微陀螺仪基本结构原理,分析了硅微陀螺仪动力学方程以及温度变化对硅微陀螺仪谐振频率、品质因数、标度因数和零偏的影响。然后,设计了基于FPGA的硅微陀螺仪数字化补偿电路。最后,经过温度特性实验得到标度因数和零偏随温度变化曲线,建立了温度补偿模型,提出分段温度补偿方法。经过温度补偿后,标度因数和零偏的温度系数分别由316.66×10-6/℃和366.22°/(h·℃)减小为69.67×10-6/℃和115.25°/(h·℃),证明了补偿方法的正确性和可行性。     

高分子聚合物约束阻尼复合结构的计算

摘 要 论述了高分子聚合物约束阻尼复合结构损耗因子的有限元计算方法，并详细研究了模态应变能法的理论分析及其在ANSYS软件上计算约束阻尼复合结构损耗因子的计算程序。