Solid state interfacial reactions in electrodeposited Ni/Sn couples

Ni/Sn couples,prepared by sequentially electroplating Ni layers and Sn layers on metallized Si wafers,were employed to study the mierostructures and growth kinetics of Ni-Sn intermediate phases,when the Ni/Sn couples were aged at room temperature or annealed at temperatures from 150 to 225℃for various times.The results show that the NiSn phase and Ni_3Sn_4 phase are formed,respectively,in the aged couples and annealed couples.The Ni_3Sn_4 layer is continuously distributed between the Ni and Sn sides in t...     

仓式静态连续好氧堆肥发酵工艺的水气研究

采用仓式静态连续好氧堆肥发酵工艺,通过建立水平衡体系,系统地研究了水分对整个发酵工艺的影响,得出了仓式静态连续好氧堆肥发酵具有工艺简便,热交换快,水气蒸发量大等特点;好氧堆肥发酵过程中发酵温度保持在65℃左右,含水量控制在45%～55%有利于有机物降解,垃圾堆肥可在40～50d腐熟;静态连续好氧一次堆肥发酵物料的含水量需控制在35%以下,机械自动分选(类)筛分效率高,筛分率在90%～95%,垃圾减容在50%～60%.二次堆肥发酵物料的含水量需控制在25%～30%,机械除杂(碎石、碎玻璃等)效果好,有机肥中杂质含量低于0.8%.静态好氧二次堆肥发酵可以用垃圾渗沥水补充水分,达到资源循环再利用,可实现污水零排放.     

有限体积法求解立体角离散误差

为解决采用有限体积法求解辐射传输方程时引起离散误差的问题,从有限体积法立体角内热流密度的求解过程出发,运用泰勒级数推导了近似误差的表达式,并分析影响离散误差的各种因素,包括离散射线数,辐射强度分布,假散射及网格比.根据分析结果,采用辐射强度的连续分布模型,模拟了各种因素对误差的影响.结果表明,辐射强度的分布函数对于有限体积法的离散误差有一定程度影响.当增加网格数及减小网格尺寸比时,可以有效地减小离散误差.假散射与离散误差间呈较强的非线性耦合关系.     

道路交通状态预测研究

针对道路交通状态预测的研究成果,综述了基于实时数据分析的道路交通状态预测理论和方法的相关研究.从分析基于实时数据分析的道路交通预测的基本流程、特点和要求和单一断面交通状态预测和多断面交通状态预测角度回顾了道路交通状态预测的研究现状.结果表明:在不断发展完善单一断面预测方法的同时,需要发展以多个断面交通状态为研究对象的多断面预测方法,以促进我国智能交通系统的基础理论发展及其应用水平的提高.     

CFRP加固钢筋混凝土梁滞后应变计算方法

为了系统研究从零负载状态到满负载状态各个阶段CFRP片材加固梁滞后应变的计算方法,在充分考虑加固梁不同负载状态及受压区混凝土非线性本构关系的基础上,分别建立了不同负载贴片加固梁考虑混凝土抗拉作用时的滞后应变计算公式及不考虑混凝土抗拉作用时的简化计算公式.试验数据和对比分析结果表明:"考虑混凝土抗拉作用"公式的计算结果与试验数据吻合良好,计算误差<8%,明显优于现有文献的计算方法;"不考虑受拉区混凝土抗拉作用"公式的计算结果在混凝土开裂前和试验值相差较大,但对已裂加固梁的计算误差与"考虑混凝土抗拉作用"公式的计算误差接近.为简化计算,对未裂和已裂混凝土梁贴片加固时的滞后应变可分别采用"换算截面"公式和"不考虑混凝土抗拉作用"公式进行计算,两种简化方法的误差均不会超过10%.     

混合匹配规则的否定选择算法

针对目前基于免疫的检测器生成算法中,匹配规则单一造成的检测器质量低下的问题,提出一种基于混合匹配规则的否定选择算法,采用海明距离整体匹配的各段内R连续比特匹配的否定选择算法,即混合匹配否定选择算法,对算法的性能进行了分析．实验结果表明,该算法能够高效地产生所需要的检测器,提高了检测率,且降低了误报率．     

Design of the low power wake-up receiver for internet of things communication

A wake-up receiver with high energy efficiency and low power consumption is proposed for solving the power consuming problems of wireless nodes communication in the Internet of Things. The proposed wake-up receiver based on the wake-up mechanism can effectively schedule the network nodes communication, and use the simple envelope detection structure to achieve frequency down-conversion, which can flexibly manage energy and reduce power consumption. Based on UMC 65nm CMOS process technology, the wake-up receiver is designed and simulated. The results show that it can achieve S₁₁ of -21dBm and a sensitivity of -75dBm at a data rate of 1Mb/s, when operating at the central frequency of 780MHz and input signal adopting an on-off keying (OOK) modulation, and the power consumption is 82μW at 1.2V voltage supply.     

电控柴油机分缸均衡控制算法及试验

柴油机各个气缸的进气量、喷油量、燃烧等存在差异,导致气缸间存在做功差异,直接影响柴油机转速的平稳性以及排放性能等。针对位置式电控柴油机,采用PI闭环控制,通过瞬时转速信号识别并计算各缸的工作差异,利用分缸均衡控制算法对油量进行补偿修正。试验结果显示低转速稳态工况转速波动由7 r/min降至3 r/min,各缸工作不均匀度由±5 r/min降至±2 r/min,在瞬态过程和高转速3 400 r/min时该算法仍然适用有效。     

Electrochemical and microstructural characterization of cyclic redox behaviour of SOFC anodes

The oxidation of Ni to NiO in solid oxide fuel cell (SOFC) anode will result in large bulk volume change, which may change the interfaces of the two phases in the anode cermet and thus may cause significant performance degradation. The reduction and oxidation (redox) of the Ni/YSZ cermet were studied at 800 ℃. Anodic polarization measurements were performed before and after redox cycles. The anode current density at an overpotential of 100 mV kept decreasing during the whole redox treatment. It decreased from 19.11 to 7.95 mA·cm-2 after two redox cycles. Anode supported unit cell was assembled for cell's discharge measurements. Cell performance declined after each redox cycle. The maximum power density decreased from 126.28 to 40.32 mW·cm-2 . The microstructural changes after redox cycling were recorded using scanning electron microscopy (SEM). The results reveal that after re-oxidation, the Ni gets coarse and has a higher porosity; the nickel network structure turns to be desultory.     

Recent progress of CERN RD50 Collaboration

The objective of the CERN RD50 Collaboration is to develop radiation hard semiconductor detectors for very high luminosity colliders, in particular, for the upgrade of the large hadron collider （LHC） which itself is scheduled to be operational in 2007. The approach of the RD50 has two major research lines, material engineering and device engineering. These are further subdivided into projects covering defect characterization and engineering, new detector materials, detector characterization, new detector structures and full detector systems. Presently, 264 members from 53 institutes are actively participating in the RD50 Collaboration. Detectors made of defect engineered substrates, e.g. high resistivity magnetic Czochralski （MCz-Si）, epitaxial silicon （Epi-Si） on Czochralski silicon （Cz-Si） substrate, intentionally thermal donor （TD） compensated p-type MCz-Si and oxygen enriched （DOFZ） silicon, have been demonstrated by the RD50 Collaboration. An overview and highlights of the results of these defect engineering techniques were given in this report.