A new bubble-point-pressure correlation for the binary LiBr/H2O solution

In accord with the increasing concern about the global environmental issues, the absorption refrigeration heat-pump systems are currently being considered very promising and attractive. For the purpose of supporting the advanced R&D technology in this area, we have developed a novel correlation to represent the bubble-point pressures of LiBr H₂O solutions. The developed correlation covers the most extensive range of validity ever proposed: 273–483 K for temperatures, 0.05 kPa to 1.0 MPa for pressures. and 29 76 wt% LiBr for concentrations.Paper presented at the Twelfth Symposium on Thermophysical Properties, June 19–24, 1994. Boulder, Colorado, U.S.A.     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

论高层建筑中央空调水系统水压试验的步骤

通过对中央空调水系统安装的特点分析,确定了应用效果良好的试压步骤。     

Ideal-gas thermodynamic properties for natural-gas applications

Calculating caloric properties from a thermal equation of state requires information such as isobaric heat capacities in the ideal-gas state as a function of temperature. In this work, values for the parameters of thec _p ⁰ correlation proposed by Aly and Lee were newly determined for 21 pure gases which are compounds of natural gas mixtures. The values of the parameters were adjusted to selectedc _p ⁰ data calculated from spectroscopic data for temperatures ranging from 10 to 1000 K. The data sources used are discussed and compared with literature data deduced from theoretic models and caloric measurements. The parameters presented will be applied in a current GERG project for evaluating equations of state (e.g., the AGA 8 equation) for their suitability for calculating caloric properties.     

柴油机针阀体的乙炔低压渗碳

乙炔低压渗碳可以有效地避免在真空渗碳过程中产生炭黑和焦油，同时由于乙炔具有较高的供碳能力，使这一技术尤其适用于针阀体这样的小直径深盲孔零件。     

Finite elements in the analysis of pressure vessels and piping-a bibliography (1976–1996)

The paper gives a bibliographical review of the finite element methods (FEMs) applied for the analysis of pressure vessel structures/components and piping from the theoretical as well as practical points of view. The range of applications of FEMs in this area is wide and cannot be presented in a single paper; therefore the aim of this review is to give the reader an encyclopaedic view of the differnt possibilities that exist today for the finite element analysis in the fields of pressure vessels and piping. The bibliography at the end of the paper contains approximately 1900 references to papers, conference proceedings and theses/dissertations on the subject that were published in 1976–1996. These are classified in the following categories: linear and non-linear, static and dynamic, stress and deflection analysis; stability problems; thermal problems; fracture mechanics problems; contact problems; fluid-structure interaction problems; manufacturing of pipes and tubes; welded pipes and pressure vessel components; development of special finite elements for pressure vessels and pipes; finite element software; and other topics. Also finite element software, general purpose and special purpose codes, used for the analysis of pressure vessels and pipes are briefly discussed and presented.     

井下储存式电子压力计的软件设计

周静等．井下储存式电子压力计的软件设计．测井技术，１９９４，１８（４）：２８１～２８７论述小功耗井下储存式电子压力计测试系统的组成及系统软件工作原理。利用软硬件结合的方式，来达到降低功耗之目的。特别是采用了软件监视定时器，以便提高系统的稳定性。系统的特点是功耗小，抗干扰能力强，稳定性好，精度高。它与袖珍计算机ＰＣ－Ｅ５００配合进行采集，处理和绘出压力恢复曲线。     

挡土墙填土曲线破裂面的地震主动土压力分析

在地震作用影响下，墙后填土处于极限平衡状态时，假定破裂面为一条通过墙趾的旋轮线。从墙后土楔中取出一微薄水平层，研究其在水平惯性力下的平衡，得到的地震土压力分布和土压力合力作用点位置均与实验结果相吻合。     

SIMILARITY LAW OF FLUCTUATING PRESSURE WITHIN HYDRAULIC JUMP AREA

Through a series of model tests of five scales for 2-D free hydraulic jump, the da-ta of fluctuating pressure acting on the floor level within the hydraulic jump were obtained. Dur-ing the experiments, Froude number varied from 2.94 to 8.61, and Reynolds number rangedfrom 2×10~4 to 6×10~5. Experiment results indicate that the amplitude scale of fluctuating pres-sure is the length scale of model, i. e. P'=L, which agrees with gravity similarity law: Thefrequency scale of the fluctuating pressure is a unity i. e., f=1, which does not satisfy thegravity similarity law.     

铸造Ti—0.2Pd合金SF—1000双级风机叶轮的研制

Ｔｉ－０．２Ｐｄ合金ＳＦ－１０００双级风机叶轮是大型盐酸再生设备的主要部件，采用整体铸造方法制造，无论在技术上还是经济上都是十分有利的。本文主要介绍采用加工石墨，铸铁组合型，真空电弧凝壳熔炼铸造工艺，成功地研制出整体铸造风机叶轮。