利用空间多普勒调谐技术冷却原子及其速度单一化

本文理论计算了用圆锥管内多次全反射激光而产生的多普勒频移来冷却原子束的机制。给出了最佳冷却原子束的圆锥管的夹角、长度、反射次数及激光入、出射角等参数。理论计算了原子束经过圆锥管冷却的速度分布情况。数值计算结果表明：采用两个长１３０ｃｍ的锥形管来冷却原子束，选用合适的失谐量可使极大部分速度小于１２００ｍ／ｓ的原子冷却到８ｌｍ／ｓ，并且可得到单一速度的高亮度的原子束。     

Numerical simulation model of vibration responses of rectangular plates embedded with piezoelectric actuators

A numerical simulation model for random large amplitude vibration control of composite plate using piezoelectric material is presented. The H_∞ control design is employed to suppress the large amplitude vibrations of composites plates under random loading. The numerical simulation model is developed and based on the finite element method. The finite element governing equation includes fully coupled structural and electrical nodal degrees of freedom, and consider the von Karman large amplitude vibration. The modal reduction method using the structural modes is adopted to reduce the finite element equations into a set of modal equations with fewer degrees of freedom. The modal equations are then employed for controller design and time domain simulation. In the simulations without control, the value of the linear mode to the nonlinear deflection is quantified; and the minimum number of linear modes needed for accurate model is obtained. In the simulations with control, it is shown that the truncated modes, which are neglected in the control design, deteriorate the controller performance. Generally, the vibration reduction level is not monotonically increasing with the size of the piezoelectric actuator. The optimal piezoelectric actuator size depends on the excitation level. For higher excitation level, optimal actuator size is larger. The H_∞ controller based on the linear finite element formulation gives better vibration reduction for small amplitude vibration, but it still gives reasonable performance for large amplitude vibration provided that the piezoelectric actuator is big and powerful enough.     

机组油膜振荡故障的诊断和处理

通过对广州发电厂1号机组3号轴承突发剧烈振动的现象和测试结果的分析，对振动故障进行诊断并提出解决办法，对3号轴承轴瓦进行处理后，机组恢复正常运行状态。     

转子系统热膨胀状态下固有横振频率

把转子的惯性力看成作用在轴上的外力,采用新的非线性渐近法研究热膨胀对转子系统固有横振频率的影响.     

结构振动控制中压电阻尼技术研究—压电被动阻尼技术（一）

压电阻尼技术有两种类型：压电被动阻尼技术和压电主动阻尼技术。本文对其中的压电被动阻尼技术进行了研究，结果表明：通过给压电元件并联适当的外部电路，可使压电系统具有与粘弹阻尼材料及动力吸振器相似的物理特性。合理配置电路参数，可以实现最优阻尼比。     

爆破地震效应及其控制措施分析

通过对爆破地震效应的产生、危害及其影响因素分析，给出了减小爆破地震效应的措施。     

Random Vibration of Systems with Viscoelastic Memory

The equation of motion of linear dynamic systems with viscoelastic memory is usually expressed in a integrodifferential form, and its numerical solution is computationally heavy. In two recent papers, the writers suggested that the system memory be accounted for through the introduction of a number of additional internal variables. Following this approach, the motion of the system is governed by a set of first-order, linear differential equations, whose solution is quite easy. In this paper, the approach is extended to single-degree-of-freedom systems subjected to random, nonstationary excitation. The equations governing the time variation of the second-order statistics are derived, and an effective step-by-step solution procedure is proposed. Numerical example shows the accuracy of the procedure for white and nonwhite excitations.     

基于协方差矩阵变换的相干源个数估计

正确地估计信号源个数是高分辨阵列信号处理的一个重要组成部分,本文提出了一种相干源个数估计的方法。这种方法是先采用空间平滑技术对信号源去相关,然后对阵列协方差进行酉变换,最后用基于协方差矩阵变换的信息论准则和盖氏半径(Gerschgorin Radii)两种方法估计信号源个数。计算机仿真结果证实了方法的可行性。     

基于切削振动相关性识别刀具磨损状态的模型与实验

本文提出基于切削振动相关性识别刀具磨损状态的研究思想,建立了车削中刀杆双向横振动系统及其单输入双输出系统的数学模型。理论和实验均表明,刀杆双向横振动之加速度响应在固有基频处的相干函数与刀具磨损状态之间有很好的规律性,它反映了两者之间的本质机理,并提供了识别刀具磨损状态的新途径。     

变速切削系统振动频率的变化特征

本文主要讨论变速切削系统中颤振频率随机床主轴转速变化的规律。理论分析和试验结果都证明在变速切削中颤振频率随转速呈分段线性锯齿状变化。试验在立式铣床和普通车床上进行。