自适应阵对角线加载研究

本文分析了对角线加载对自适应阵性能的影响，提出了加载门限的概念，以及加载门限的计算公式，为加载量的选取提供了方法和依据，并将加载研究的结果加以推广，提出了有效的ＬＳ自适应波束形成算法的非零初始化方法。     

机器人腕力传感器的动态负载效应

本文从时域和频域两方面研究机器人腕力传感器在加载情况下的动态响应，进行动态建模和频谱分析，探讨负载效应的影响。     

Characteristics of hydrostatic bearing/seal parts for water hydraulic pumps and motors. Part 1: Experiment and theory

In this paper, the load-carrying capacity, power losses and stiffness of disk-type hydrostatic thrust bearings including the case of eccentric loading are discussed theoretically. The numerical analysis method is established based on a two-dimensional elastohydrostatic problem with an elastic deformation model, which is extended to adapt it for a non-axisymmetric load acting on the thrust bearing. The bearing is made of a combination of stainless steel/stainless steel and stainless steel/plastics. For the elastic materials, the maximum stiffness derived from, i.e., minimum film thickness is, larger than that of the rigid material in the range of a large ratio of pocket pressure and a hydrostatic balance ratio of over unity, which is defined as the ratio of the load to the maximum hydrostatic load-carrying capacity. The maximum load-carrying capacity and minimum power loss can exist in the domain of the hydrostatic balance ratio over unity for the case of the bearing consisting of elastic/rigid materials, in comparison with that composed of the same rigid materials. For the case of water, the power loss due to leakage flow is slightly larger but that due to frictional torque is much smaller than that in the case of hydraulic oil. Then, the total power loss is much smaller than that of hydraulic oil.     

低频电脉冲采油工程设备的开发与应用

低频电脉冲采油技术是通过升压、整流、充电等电路将电能蓄积在电容器中,通过触发电路,使能量瞬时释放,在井内液体中产生震动波,作用于地层,改善地层的渗流状况,达到提高采收率的目的。Ⅰ型设备在双河油田应用11井次,成功率72%;Ⅱ型设备在古城油田应用10井次,成功率90%。主要是由于Ⅰ型设备关键部件在处理油井时要放在井下,受高温、高压的影响及井下空间的限制,设备稳定性差、寿命短、能量小、效果差;Ⅱ型设备解决了上述问题,从而提高了试验成功率。     

Mixed Mode VLSI Implementation of a Neural Associative Memory

A mixed mode digital/analog special purpose VLSI hardware implementation of an associative memory with neural architecture is presented. The memory concept is based on a matrix architecture with binary storage elements holding the connection weights. To enhance the processing speed analog circuit techniques are applied to implement the algorithm for the association. To keep the memory density as high as possible two design strategies are considered. First, the number of transistors per storage element is kept to a minimum. In this paper a circuit technique that uses a single 6-transistor cell for weight storage and analog signal processing is proposed. Second, the device precision has been chosen to a moderate level to save area as much as possible. Since device mismatch limits the performance of analog circuits, the impact of device precision on the circuit performance is explicitly discussed. It is shown that the device precision limits the number of rows activated in parallel. Since the input vector as well as the output vector are considered to be sparsely coded it is concluded, that even for large matrices the proposed circuit technique is appropriate and ultra large scale integration with a large number of connection weights is feasible.     

预处理工艺对硬质合金与金刚石膜间粘结力的影响

在两种经不同预处理的硬质合金YG8基底上，采用微波等离子体化学气相沉积法，在微波功率2kW，压强4.0kPa和6.5kPa，CH4和H2流量分别为1.6cm/s和100.0cm/s的条件下生长金刚石薄膜。利用X射线衍射检测了金刚石薄膜是否存在，用拉曼光谱分析了薄膜的质量，用金相显微镜观察了薄膜的洛氏硬度压痕，标定并比较了不同预处理工艺膜与基底的结合力。实验结果表明，不同的预处理方法对于粘结力的影响不大，最主要的因素是钴含量的多少。     

电动潜油泵多功能自动控制测试系统

为了提高电潜泵产品质量 ,延长电潜泵井的检泵周期 ,研制了电动潜油泵多功能自动控制测试系统。该系统由自动控制、参数测试、管线流程及电气控制 4部分组成 ,既能对电潜泵机组进行全面检测 ,又能对测试数据进行管理和跟踪 ,具有测试参数齐全、速度快、精度高、操作容易、安全性强、智能化程度高、测量范围广、容量大等特点 ,并在计算机自动调节井口压力、测试电动机转矩以及测控回路与计算机分离等方面具有创新。该系统能够模拟现场工况完成各种型号的电潜泵的测试 ,为电潜泵的理论设计及现场应用提供可靠的试验数据。