Prediction of the effects on dynamic response due to distributed structural modification with additional degrees of freedom

The aim of this study is to investigate means of efficiently assessing the effects of distributed structural modification on the dynamic properties of a complex structure. The dynamic properties of the modified structure can be determined by experimental testing or numerical simulation, both of which are complex, expensive and time-consuming. Assuming that the original dynamic characteristics are already established and that the modification is a relatively simple attachment, the modified dynamic properties may be determined numerically without solving the equations of motion of the full-modified structure. The frequency response functions (FRFs) of the modified structure can be computed by coupling the original FRFs and a delta dynamic stiffness matrix for the modification introduced. The validity of this approach is investigated by applying it to a cantilever beam to which a smaller beam is attached as modification. The original FRFs were obtained experimentally as well as numerically. The delta dynamic stiffness matrix was determined numerically by modeling the attachment and part of the original structure including the attachment points. The FRFs of the modified beam were then computed. Good agreement is obtained by comparing the results to the FRFs of the modified beam determined experimentally as well as by numerical modeling of the complete modified structure.     

郑411块超稠油试油试采工艺技术应用

郑411块沙三段地层疏松出砂、原油粘度高，属中深层超稠油，常规试油试采方法难以突破出油关，采用APR全通径氮气垫测试、地层与井筒复合防砂、水平井配合直井蒸汽吞吐、氮气泡沫封堵调剖和井筒加热举升稠油等配套工艺技术，取得了较好的效果，为中深层超稠油油藏的开发提供了技术思路。     

日本关西宽带实验网印象

本文根据实地考察内容，结合宽带网络技术和业务重点及实施策略，全面介绍了日本关西宽带实验网发展背景，通信与广播电视综合应用实验和Ｂ－ＩＳＤＮ实用化实验的进展以及ＮＴＴ所起作用。文章最后就关西宽带实验网的借鉴意义提出了几方面意见。     

Design and Characterization of the CLIMPAQ,Chamber for Laboratory Investigations of Materials,Pollution and Air Quality*

A test chamber has been developed in order to provide a small and simple emission testing facility capable of testing construction products in a climate where the important climatic parameters such as temperature, ventilation rate and air velocity can be varied independently around typical indoor values. The test chamber CLIMPAQ is made of panes of window glass. Other main surface materials are stainless steel and eloxated aluminium. The chamber has a volume of 50.9 litres and is designed to meet the requirements for quantifying air pollution. In this investigation human subjects acted as air pollution judges, and chemical characterization of the air pollution was carried out. Carpet, linoleum, wall paint and seal- ant were tested simultaneously in the CLIMPAQ and in four other chambers ranging from a full-scale chamber of 28 m³ to a field and laboratory emission cell of 3.5· 10^?5m³. Product ranking is the same in all chambers for the sensory measurements. Emission rates based on sensory measurements differ for all products less than 100 % except for tests in a 3-litre chamber where emission rates were higher. Chemical measurements differ up to approximately 10 times for the same product in different chambers. Deviations appear to be the result of different environmental parameters in the various chambers. Low air concentrations or high specific ventilation rates seem to increase emissions, while differences in air velocities and sink properties may also be the cause of differences in emission rates.     

Frequency response function of magnetic bearings using high-temperature superconductor

A high-temperature superconductor YBa₂Cu₃O_7-x with strong pinning force has allowed stable magnetic suspension with no control to be developed. Two types of superconducting magnetic bearings (SMB) using YBCO and permanent magnet were assembled. The two types are radial and axial. The dynamic stiffness of each SMB as it was cooled down under a magnetic field by liquid nitrogen was measured both radially and axially. As a result, it was found that the spring constants of these SMBs were almost as large as a practically desirable value; however, their damping coefficients were lower than the practical level. These findings are useful as one of the data bases for development of an optimum SMB design to support the weight of rotors in an axial direction.     

二流量试井工艺及资料解释分析方法

描述了二流量试井工艺的实现，从常规分析和双对数曲线拟合两上方面，给出了二流量试井的资料解释分析方法，分析认为二流量试井同样可以计算出正常关井测压力恢复（或压力降落）资料所解释的油藏及流体参数。这种试井方法不但可以减少因正常关井测压对产油量和注水量的影响，而且可以减缓因突然关、开井造成的套管变形或损坏。实践证明，该试井技术方法具有较好的经济效益和应用前景。     

Thermal Monitoring of Self-Checking Systems

With the increasing power density in integrated systems resulting from scaling down, the occurrence of field failures due to overheating has considerably increased. Faulty operation can be prevented by on-line temperature monitoring. This paper deals with questions of on-line temperature monitoring in safety-critical systems. First the possible temperature sensors are reviewed and basic principles of self-checking systems including such sensors are detailed, then a new temperature sensor cell with extremely good parameters designed especially for DfTT applications is presented. The basic questions of integrating thermal sensors into self-checking systems are also discussed.     

用于疏通油水井的脉冲放电技术

评价了各种不同的解堵技术，指出冲击波解堵是一种很有发展前途的技术。介绍了液中脉冲放电产生冲击波的基本原理，并由此研制出了一套井下脉冲放电油水井处理设备样机。通过现场试验，表明用冲击波疏通油井能较好地解除油井污染，提高采收率。     

可燃气体检测报警系统的分析和检修

分析可燃气体检测报警系统的组成和检修方法，并列举了根据故障现象进行分析和检修的实例。     

Current ISI and monitoring technologies in European energy industries

This paper reviews available information on the state of practice of inservice material property monitoring performed in European energy industries. Current practice includes a range of standard nondestructive testing and monitoring methods, improved remote sampling and surveillance specimen testing, and new monitoring techniques which are emerging from ongoing development programs. These new technologies include ultrasonic, positron annihilation, neutron diffraction, and magnetic techniques.