Mechanoluminescent pulse pressure sensors. Processing of output optical signal

The process of mechanoluminescence transformation of a pulse pressure sensor is considered. The process consists in excitation of emission under the action of mechanical loading. An algorithm for use in processing the output optical signal of the sensor that makes it possible to determine an input shock pulse is presented. __________ Translated from Izmeritel’naya Tekhnika, No. 10, pp. 28–31, October, 2007.     

基桩反射波法动测曲线的数值模拟与特征分析

采用美国PDI公司开发的PDI-S软件,对不同缺陷基桩的反射波法低应变动测曲线进行数值模拟,对动测曲线的特征进行归纳与总结,以便在解释反射波法曲线时作为参考与借鉴,提高基桩质量检测的可靠度。     

钛合金的银脆,镉脆敏感性及其控制

利用慢应变速率拉伸技术（ＳＳＲＴ），并结合恒载实验，较全面地研究了Ｔｉ－６Ａｌ－４Ｖ合金的银脆行为、固态与液态镉脆行为，确定了应变速率、接触条件、热处理制度、试样取向、温度等因素对Ｔｉ－６Ａｌ－４Ｖ合金银脆与镉脆敏感性的影响，探讨了Ｎｉ阻挡层对控制Ｔｉ－６Ａｌ－４Ｖ合金和ＴＣ１１合金银脆开裂的作用。     

压阻式压力传感器及其应用电路设计

介绍了压阻式传感器的工作原理以及相关应用电路，并给出了一个应用示例加以说明。     

K0.9Li0.1（Ta0.5Nb0.5）O3晶体压电应变系数的测量

用准静态ｄ＿（３３）测量仪和干涉法相结合。测量了Ｋ＿（０．９）Ｌｉ＿（０．１）（Ｔａ＿（０．５）Ｎｂ＿（０．５）Ｎｂ＿（０．５））Ｏ＿３晶体的压电应变系数。结果为：ｄ＿（３３）＝８６．０，ｄ＿（３３）＝一２９．５，ｄ＿（１５）＝１１２．９×１０￣（－１２）Ｃ／Ｎ．     

关于离散Kirchhoff薄板单元的研究

本文对离散Kirchhoff薄板单元进行了深入的分析。文中将用于建立离散Kirchhoff单元的泛函分为三部分,分别用应变第一不变量、绕Z轴的转动偶和有关的单元边界上的积分来表达,并阐明了各部分的作用。其中单元的收敛性质完全由第一、三部分所决定,而第二部分则控制了单元的计算精度。在此基础上,文中建议了一种提高离散Kirchhoff单元精度的新方法,并由此推导了一个任意四边形离散Kirchhoff单元。计算表明,本文的改进单元与原来的离散Kirchhoff单元及其改进型相比,计算精度有了显著提高。     

Non‐reflecting artificial boundaries for transient scalar wave propagation in a two‐dimensional infinite homogeneous layer

This paper presents an exact non‐reflecting boundary condition for dealing with transient scalar wave propagation problems in a two‐dimensional infinite homogeneous layer. In order to model the complicated geometry and material properties in the near field, two vertical artificial boundaries are considered in the infinite layer so as to truncate the infinite domain into a finite domain. This treatment requires the appropriate boundary conditions, which are often referred to as the artificial boundary conditions, to be applied on the truncated boundaries. Since the infinite extension direction is different for these two truncated vertical boundaries, namely one extends toward x →∞ and another extends toward x→‐ ∞, the non‐reflecting boundary condition needs to be derived on these two boundaries. Applying the variable separation method to the wave equation results in a reduction in spatial variables by one. The reduced wave equation, which is a time‐dependent partial differential equation with only one spatial variable, can be further changed into a linear first‐order ordinary differential equation by using both the operator splitting method and the modal radiation function concept simultaneously. As a result, the non‐reflecting artificial boundary condition can be obtained by solving the ordinary differential equation whose stability is ensured. Some numerical examples have demonstrated that the non‐reflecting boundary condition is of high accuracy in dealing with scalar wave propagation problems in infinite and semi‐infinite media. Copyright © 2003 John Wiley & Sons, Ltd.     

Analytical solution for the axisymmetric plane strain electroelastic dynamics of a special non-homogeneous piezoelectric hollow cylinder

By virtue of the introduction of a dependent variable and the separation of variables technique, the axisymmetric plane strain electroelastic dynamic problem of a special non-homogeneous piezoelectric hollow cylinder is transformed to a Volterra integral equation of the second kind about a function with respect to time, which can be solved successfully by means of the interpolation method. Then the solutions of displacements, stresses, electric displacements and electric potential are obtained. The present method is suitable for a piezoelectric hollow cylinder with an arbitrary thickness subjected to arbitrary mechanical and electrical loads. Numerical results are finally presented.     

Neutron Stress Measurement of W‐Fiber Reinforced Cu Composite

Stress measurement methods using neutron and X‐ray diffraction were examined by comparing the surface stresses with internal stresses in the continuous tungsten‐fiber reinforced copper‐matrix composite. Surface stresses were measured by X‐ray stress measurement with the sin²ψ method. Furthermore, the sin²ψ method and the most common triaxal measurement method using Hooke's equation were employed for internal stress measurement by neutron diffraction. On the other hand, microstress distributions developed by the difference in the thermal expansion coefficients between these two phases were calculated by FEM. The weighted average strains and stresses were compared with the experimental results. The FEM results agreed with the experimental results qualitatively and confirmed the importance of the triaxial stress analysis in the neutron stress measurement.     

部件试验模态综合的简便方法

本文将一种基于完备模态基的模态综合技术应用于子结构的试验模态综合,获得成功。这种半试验半理论的模态综合方法是一种较为简便的、要求试验工作量较小的试验模态综合法,因为它只要求测量子结构的振动模态和频率即可。数值仿真结果表明,这种简便的试验模态综合法是行之有效的。