Effects of structural characteristics on microwave dielectric properties of low-loss (Zn1-xNix)ZrNbTaO8 ceramics

Low-loss (Zn_1-xNi_x)ZrNbTaO₈ (0.02?≤?x?≤?0.10) ceramics possessing single wolframite structure are initiatively synthesized by solid-state route. Based on the results of Rietveld refinement, complex chemical bond theory is used to establish the correlation between structural characteristics and microwave performance in this ceramic system. A small amount of Ni²⁺ (x?=?0.06) in A-site with the fixed substitution of Ta⁵⁺ in B-site can effectually raise the Q?×?f value of ZnZrNb₂O₈ ceramic, embodying a dense microstructure and high lattice energy. The dielectric constant and τ_f are mainly affected by bond ionicity and the average octahedral distortion. The (Zn_0.94Ni_0.06)ZrNbTaO₈ ceramic sample sintered at 1150?°C for 3?h exhibits an outstanding combination of microwave dielectric properties: ε_r =?27.88, Q?×?f?=?128,951?GHz, τ_f =?–39.9?ppm/°C. Thus, it is considered to be a candidate material for the communication device applications at high frequency.     

DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

Liquid phase sintering and characterization of SiC ceramics

The present study focuses on the sintering of silicon carbide-based ceramics (SiC) by liquid phase sintering (LPS) followed by characterization of the produced ceramics. AlN/Re₂O₃ mixtures were used as additives in the LPS process. In the first step, the LPS-SiC materials were produced in a graphite resistance furnace in the form of discs at different temperatures. The conditions with the best results regarding real density and relative density were taken as reference for sintering in the form of prismatic bars. In the second step, these samples were evaluated regarding fracture toughness (K_IC), by the Single Edge V Notch Beam – SEVNB – method, and flexural strength. K_IC behavior was evaluated according to the depth and curvature radius of the notches. Reliable K_IC values were presented when the ceramic displayed a small curvature radius at the notch tip. When the radius was large, it did not maintain the square root singularity of the notch tip. Tests were carried out to determine K_IC values in atmospheric air and water. K_IC results were lower in water than air, with a decrease ranging between 2.56% and 11.26%. The observations indicated a direct grain size correlation between K_IC values and fracture strength of the SiC ceramics.     

基于密集神经网络的灰度图像着色算法

针对在灰度图像着色领域中，传统算法信息提取率不高、着色效果不理想的问题，提出了基于密集神经网络的灰度图像着色算法，以实现改善着色效果，让人眼更好地观察图片信息的目的。利用密集神经网络的信息提取高效性，构建并训练了一个端到端的深度学习模型，对图像中的各类信息及特征进行提取。训练网络时与原图像进行对比，以逐渐减小网络输出结果的信息、分类等各类型的损失。训练完成后，只需向网络输入一张灰度图片，即可生成一张颜色饱满、鲜明逼真的彩色图片。实验结果表明，引入密集网络后，可有效改善着色过程中的漏色、细节信息损失、对比度低等问题，所提算法着色效果较基于VGG网络及U-Net、双流网络结构、残差网络（ResNet）等性能优异的先进着色算法而言取得了显著的改进。     

低插损窄带型10.7MHz压电陶瓷滤波器的研制

介绍了低插损窄带型10.7 MHz压电陶瓷滤波器的一种设计制作方法。结合压电陶瓷能陷模理论,通过对滤波器分割电极设计和制造工艺控制技术的研究,强调了工艺控制的重要性。产品达到日本村田同类产品水平,对国产化窄带型10.7 MHz压电陶瓷滤波器的研发和生产具有十分重要的意义。认为选用高Qm值压电陶瓷材料、分割电极和耦合电容的设计、焊接和点蜡工艺的控制等是研制低插损窄带型10.7 MHz压电陶瓷滤波器的重点。     

Deformation-Strength Relationships in Short-Term Tension of Heat-Resistant Materials

The analysis of 124 curves obtained in short-term tensile tests demonstrate that they can be described by varying strain hardening and softening characteristics. Different stress–strain curves can be produced at invariable yield strength and ultimate strength and interrelated proportional variations of the above characteristics. To determine some specific stress–strain curve, it is necessary to take account of yield strength and ultimate strength as well as strain corresponding to the latter. The relations between yield strength, ultimate strength and hardening and their practically complete absence between these parameters and softening were statistically established.     

辐射型漏泄同轴电缆的设计

总结了漏泄同轴电缆的理论研究现状。围绕使用频带和耦合损耗这两个重要电气参数，讨论辐射型漏泄同轴电缆的设计方法。基于周期性槽孔结构的空间谐波的分析，讨论了抑制高次谐波以拓展使用频带的方法。利用时域有限差分方法和Matlab软件计算耦合损耗。     

深水井控中节流管线摩阻分析及压井方法

在海洋深水钻井中，防喷器组一般安装在海底，当发生井涌进行压井作业时．由于节流管线较长、内径较小，钻井液在节流管线内存在高摩阻损失，作用在井底的压力往往大于地层的破裂压力．从而引起压井过程的复杂化，甚至造成压井作业的失败。介绍了一种新的压井方法附加流量法，在返出的节流管线流体中混入低密度流体，降低节流管线内流体的粘度和密度，从而实现安全压井；详细介绍了压井方法和步骤。数据分析表明，通过对压井参数进行优化选择能够降低节流管线中的压耗。     

天然气井作业屏蔽暂堵技术的研究与应用

在天然气井进行井下作业前，将暂堵剂挤入生产层位附近，以暂时封堵生产层，使地层压力不被释放，井筒内的压井液不污染地层，待施工作业结束后，及时进行解堵，确保天然气井不受伤害或少伤害，从而恢复天然气井的生产能力。针对天然气井大修作业时，经常补充压井液，由于作业时间长，大量压井液进入地层，造成严重污染，导致天然气井恢复生产困难的问题，研制出一种新型气井作业的屏蔽暂堵剂，具有污染小，易解堵等特点，有效解决了大修污染问题，现场应用取得良好效果。     

水力射孔对套管强度的影响研究

水力射孔技术是一种新型的完井方式，深穿透水力射孔技术辅助定向水力压裂可以实现油气层改造和油气井增产。但是，水力射孔套管会在孔眼处造成应力集中，使得局部应力过大而削弱了套管和水泥环的强度，可能会影响套管的使用寿命。因此，文章利用有限元软件建立了射孔套管的三维有限元模型，分析了水力射孔后套管管体的应力分布，重点研究了水力射孔参数-孔密、孔径、孔深、射孔方位角等对套管强度的影响规律。分析结果表明，沿着最大水平地应力方向深穿透水力射孔，选择合适的孔密、孔径可将射孔对套管的损害降至最小。研究结果为提高水力射孔完井设计水平提供了一定的参数依据。