考虑初始椭圆度的套管抗载能力分析

针对套管的不同初始椭圆度建立了套管、水泥环、地层平面应变力学模型。分析认为，在非均匀地应力作用下，套管内壁的径向变形较大，抗载能力明显降低，破坏主要是由地下非均匀地应力引起的；随着初始椭圆度的增加，在地应力作用下套管各部位产生的应力分布不均程度增大，使得套管抗外载能力减弱。建议在生产和使用过程中应严格将套管椭圆度控制在规定的范围内，从而提高套管的抗载能力。     

-50℃用20MnMoD钢锻件及其焊接接头性能

研究了-50℃的20MnMoD钢锻件及其焊接接头在不同热处理状态时的综合力学性能。结果表明,-50℃的20MnMoD钢锻件具有良好的低温韧性,可与-50℃级正火型低温压力容器钢15MnNiNbDR配套使用。     

长输管道建设物流管理新模式——物资配送

长输管道工程是以线路管道与沿途站场为主要内容的建设工程,其物资配送有着不同于一般物流管理的特点,点多线长,且交通不便.文章结合西南成品油管道建设工程的物资配送实践,总结出长输管道物资配送的类型,并从机构设置、计划编制、台账和报表管理等方面介绍了物资配送的管理内容及经验,实践证明,这种物资配送方法不但使业主的物资管理人员大为减少,而且使长输管道工程的物资供应更加及时有序.     

压裂斜井时射孔处雁形裂缝产生及干扰分析

在已射孔的斜井压裂过程中，射孔孔眼处会出现一系列的几乎相互平行的雁形裂缝。这些裂缝的延伸、连接受到地层应力及裂缝本身的影响，情况较为复杂，但它们的延伸和连接对压裂的成功与否至关重要。笔者对裂缝模型进行简化，将复变函数理论与位错理论相结合，并且考虑了裂缝表面有流体压力作用且裂缝之间存在相互干扰的情况下，建立了无限大介质中裂尖应力强度因子的数学模型，利用该模型可对雁型裂缝之间的相互干扰进行力学分析。应用数值方法对所建立的数学模型求解，得到裂尖的应力强度因子及转角，来预测裂缝连接情况。该结果可用来指导压裂井的射孔施工。     

A polydispersed particle system representation of the porosity for non-saturated cementitious materials

In this paper, the porosity of cementitious materials is described in terms of pore size distribution by means of a 3-dimensional overlapping sphere system with polydispersivity in size. On the basis of results established by Lu and Torquato [B. Lu, S. Torquato, Nearest-surface distribution functions for polydispersed particle systems, Phys. Rev. A 45(8) (1992) 5530-5544] and Torquato [S. Torquato, Random Heterogeneous Media: Microstructure and Macroscopic Properties. Springer-Verlag: New York, 2001] providing relations for nearest-neighbor distribution functions, the volume fraction of pores having a radius larger than a prescribed value is explicitly expressed. By adopting an appropriate size distribution function for the sphere system, it is shown that the pore size distribution of cementitious materials as detected for instance by mercury intrusion porosimetry (MIP), which generally points out several pore classes, can be well approached. On the basis of this porosity representation, the evaluation of the capillary pressure in function of the saturation degree is provided. The model is then applied to the simulation of the saturation degree versus relative humidity adsorption curves. The impact of the pore size distribution, the temperature and the thickness of the adsorbed water layer on these parameters are assessed and analyzed for three model materials having different pore characteristics.     

降雨空间分布模式识别

以广东省内186个站点的年降雨量分布为基础，把模式识别的聚类分析理论方法引入降雨空间特征分类研究中，进行降雨特征空间分布模式识别，以预测无雨量站点的降雨模式，从而分析水资源的空间分布模式，以便制订有效的水资源利用方案。结果表明，广东省年降雨量在空间上的分布可划分为6类模式；同时基于BP人工神经网络算法，建立了以高程、气温、蒸发量为主要参数的可判别和预测无雨量测站区域的降雨空间分布模式所属类别的模型，经过模型的学习和验证，效果较好。     

压裂泵往复密封性能及机理研究

根据流体动压润滑理论，对压裂泵柱塞密封摩擦副的润滑机理进行了理论分析。在排出和吸入行程，柱塞密封摩擦副均能满足流体动压润滑的条件，即在柱塞与密封界面上能形成并保持一定厚度的油膜润滑密封，从而达到减小摩擦提高寿命的目的；建立了摩擦界面油膜厚度和泄漏量的计算公式。利用有限元法理论，对密封圈的压力沿轴向的分布规律、泄漏量与压力变化关系进行了模拟计算。对往复密封圈沿轴向压力分布、泄漏量随压力变化进行了测试；试验结果表明，建立的计算模型具有较高的计算精度，揭示了压裂泵的密封机理。     

Directional features in online handwriting recognition

The selection of valuable features is crucial in pattern recognition. In this paper we deal with the issue that part of features originate from directional instead of common linear data. Both for directional and linear data a theory for a statistical modeling exists. However, none of these theories gives an integrated solution to problems, where linear and directional variables are to be combined in a single, multivariate probability density function. We describe a general approach for a unified statistical modeling, given the constraint that variances of the circular variables are small. The method is practically evaluated in the context of our online handwriting recognition system frog on hand and the so-called tangent slope angle feature. Recognition results are compared with two alternative modeling approaches. The proposed solution gives significant improvements in recognition accuracy, computational speed and memory requirements.     

辽河减压渣油中金属铁的赋存与分布特征

考察了辽河减渣在吸附分离、酸性溶液萃取和沥青质轻度降解过程中金属铁的分布和转移情况。结果表明，辽河减渣中有近90％的铁富集在胶质和沥青质中，部分铁以侧链较短的环烷酸盐或酚盐形式存在，部分铁连接在沥青质分子的侧链上，或是被包裹在沥青质大分子中。     

Optimal production-inventory policy for make-to-order versus make-to-stock based on the M/Er/1 queuing model

This paper analyzes a multi-product production / inventory system where demands for each item arrive according to a Poisson process and the production time for each product has an Erlang distribution. The paper proposes an optimality condition that specifies whether each product should be produced make-to-stock or make-to-order. In the event a product should be produced make-to-stock, an approach for computing the optimal base-stock level is proposed. Numerical examples are given for illustrative purpose.