转炉出钢口套整体袖砖工艺技术开发

介绍了天津天铁冶金集团有限公司炼钢厂转炉出钢口袖砖工艺的开发过程，主要工艺参数的制定，实践证明，该工艺的应用取得了良好的使用效果。     

企业实施精益生产的探讨

通过描述造成企业经济效益差的原因之一——浪费，提出了如何实施精益生产，消除企业浪费，以提高企业经济效益．     

Corrosion Control by water‐soluble extracts from leaves of economic plants

Water extracts from leaves of date palm, phoenix dactylifera, henna, Lawsonia inermis, and corn, Zea mays, were tested as corrosion inhibitors for steel, aluminum, copper and brass in acid chloride and sodium hydroxide solutions using weight loss, solution analysis and potential measurements. The inhibition action was found to critically depend on metal type and solution composition. Only, date palm and henna extracts were found highly effective in reducing corrosion rate of steel in acid chloride solutions and aluminum in sodium hydroxide solutions. The inhibition efficiency increased with increasing the concentration of the extract. The inhibition was interpreted in terms of chemisorption of some active ingredients in the leaves according to Temkin isotherm.     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Schäden durch kerbinduzierte Schwingbrüche

Failures by notch induced fatigue fractures Notches produce local stress concentrations and promote the formation of fatigue cracks. Characteristic types of notches as a result of design, manufacturing and operation are presented and remedial measures are discussed. Examples demonstrate the effect of different kinds of notches on various components.     

汽车发动机电机铁芯用钢(ADW2)的研制开发

鞍钢研制开发的汽车发动机启动电机用钢是针对汽车电机铁芯用钢（定、转子）而开发的电机钢类产品。介绍了该产品的研制过程及规格、特点。通过批量试制及装机试验，产品巳满足用户的使用要求。     

Thermomechanical stress fields in high-temperature fibrous composites. I: Unidirectional laminates

This two-part paper presents a closed-form procedure for evaluation of estimates of local thermomechanical stress fields in two-phase fibrous composites and laminates. The first part is concerned with a unidirectional elastic laminate subjected to uniform mechanical loads and to uniform changes in temperature. Both phases are assumed to be elastic, with temperature-dependent moduli and expansion coefficients; the solution reflects the influence of thermomechanical interactions. Exact solutions are not possible for any real system, because the local geometry is not known in detail. Instead, estimates of the fields are found from a modified Mori-Tanaka approximation. Examples are presented for two SiC/Ti---Al---Nb composites. Local stresses of interest are found after cooling from fabrication to room temperature. The presence of local yielding, and the influence of coupling terms on the local stress magnitudes are examined. Extension of the results to laminated plates is presented in Part II (Dvorak, G.J., Chen, T. & Teply, J., Composites Science and Technology, 43 (1992) 359–368, this issue).     

微合金化高强度钢轧制采用的工艺技术

本文综述微合金化高强度钢轧制采用的工艺技术，其中包括热装热送、板坯加热、控轧控冷、快速冷却、采用的新设备等工艺技术。重点是生产低碳、高韧性、高强度、易焊接的造船用钢采用形变热处理技术，以提高产量和质量，节省昂贵的Ｎｉ、Ｃｒ、Ｍｏ等合金，降低生产成本。     

在役加氢反应器试验板脆化和氢损伤的测定与研究

充分利用了带主焊缝的役后试板，在国内首次开展回火脆化、氢介质下断裂韧性与疲劳扩展的研究，结果表明，加氢反应器焊缝有明显的脆化表现。同时，核查了反应器开停车升温速度和降温速度规定，以及确定了裂纹允许尺寸的参考数据，为今后安全运行提供了充分的依据。     

45号钢二次枝晶臂间距与冷却速度的关系

本文利用可控平均冷却速度的单向凝固实验炉测定了４５号钢在不同平均冷却速度下的冷却曲线，由此得到其在凝固期间的平均冷却速度Ｒ，相应地测量了不同平均冷却速度下试样的二次枝晶臂间距Ｓ２，通过回归，得到了如下关系式：Ｓ２＝７２７Ｒ－０．４１，并将引式成功地应用于实际生产中。