三峡工程明渠提前截流方案及水力学试验研究

论述了三期明渠提前截流方案的综合比较分析及截流水力学试验研究成果。认为拟定的提前截流诸方案各有利弊 ,其截流难度较初设方案显著增加。对于截流“基本方案”及“比较方案”的成功实施 ,必须辅之以一定的工程技术措施降低截流难度     

In Situ Formation of a Novel Nanocomposite Structure Based on MCM-41 and Polyethylene

M41S materials are prepared by in situ assembly of inorganic precursors and organic template and can be viewed as nanocomposites of the siliceous phase and organic surfactant. Calcination of these precursors gives the M41S materials that have been used to prepare novel nanocomposite structures, in which the organic phase inside the nano-sized pores is isolated by the nano-sized inorganic pore walls. The nanocomposite structures can be formed by in situ polymerization of monomers inside the channels. Polymerization of ethylene takes place inside the nano-sized pores, producing the desired nanocomposite structure. The resulting polyethylene was found to be a mixture of crystalline and amorphous phases.     

Calculation of fatigue limits of case-hardened specimens with consideration of mean stresses and residual stresses

 The strength of case-hardened parts under cyclic loading can be determined in an experimental manner, but this can produce a large amount of costs due to the expenditure of material and testing time. Therefore, a calculation method is developed, that strongly reduces the number of experiments. The presented model is based on Weibull's weakest-link concept and allows to compute the survival probability of a case-hardened part which is loaded close to the fatigue limit. The essential quantities in this model are the distribution of Vicker's hardness of the material, the exponents of the Weibull distribution of the volume and the surface, the residual stress state, the surface roughness and the surface oxidation depth. By integrating the survival probabilities of the surface and the volume, the survival probability of the entire specimen or part can be calculated, which allows to compute the fatigue limit. The necessary parameters have to be determined from reference specimens. The model is successfully examined by comparing experimental and calculated results of smooth and notched case-hardened specimens under alternating torsion, rotating bending, repeated tension and tension-compression. Received 20 August 2001 / Accepted 11 November 2001     

影响塑料模压制件内应力的因素分析

主要讨论了造成塑料模压制件内应力的主要因素,包括制件造型设计不合理、模具设计不合理、成型工艺条件不正确等,并针对不同情况给出了相应的解决办法     

超薄氧化层中的中性陷阱对隧穿电流的影响和应变诱导漏电流

用数值分析的方法讨论了中性陷阱对超薄场效应晶体管(MOSFET )隧穿电流的影响.中性陷阱引起势垒的变化在二氧化硅的导带中形成一个方形的势阱.对于不同的势垒变化,计算了电子隧穿氧化层厚度为4nm的超薄金属氧化物半导体结构的电流.结果表明,中性陷阱对隧穿电流的影响不能被忽略,中性陷阱的存在使隧穿电流增加,并且通过这个简单的模型能够理解应变诱导漏电流的产生机制.     

城市燃气管网设计若干问题的探讨

分析了哈依燃气管道工程在施工及管理过程中存在的问题，并就如何解决这些问题提出了建议。     

砖混结构现浇楼板的裂缝分析及预防措施

针对目前多层住宅采用砖混结构现浇钢筋混凝土产生裂缝的情况，分析了其产生原因，提出了预防措施。指出这些预防措施可使裂缝得到有效控制。     

GAO Feng~1,LI Wei~2,TANG Zon

tific Experiment Center of Guangxi Medical University,Nanning 530021,China)Objective:To investigate the mutation pattern of adenomatous polyposis coli(APC),Kirsten-ras(K-ras) and p53 genes in sporadic colorectal cancer tissues.Meth     

Residual stress measurements in bevel gear after different production phases

This article discusses residual stress measurements by means of electrochemical removal of material layers with residual stresses and simultaneous measurement of strain on the opposite specimen side with strain gages. Exact measurements are impossible particularly because of the small bevel gear module. With the method presented, the average residual stresses in the tooth root plane and underlying layers are measured. Residual stress distribution after each consecutive production phase is plotted and analyzed. Residual stress measurements enable the engineer to adequately assess each individual production phase and by that improve the quality of the complete production process.     

软土中的基坑支护工程实例分析

武汉某地下车库基坑处于深厚淤泥中 ,采用排桩 +土层锚杆支护与放坡 +网喷分段支护方式 ,本文根据现场地质、地形条件 ,对本工程支护过程中支护桩与土体变形作了具体分析。