关于重力坝坝内细部构造设计的几个问题

重力坝常采用横，纵缝将坝体分为柱状体施工。为此，横缝须设置止水，纵缝则待坝体冷却后灌浆，将柱状坝块连成整体。此外坝体内部还须设置坝面排水管以消除坝内渗透压力。关于坝内这些细部构造，设计规范仅有原则性要求，一般专业书列举不多，目前有些工程往往参照已建工程的设计图采用，常由于施工详图不祥易发生施工质量问题。根据丹江口重力坝设计经验，对接缝灌浆中的键槽，止浆片，灌浆管道，出浆盒，排气槽及排气管，基岩陡坡     

Pullout tests of epoxy-coated reinforcement in concrete

The bond strength and slip of epoxy-coated reinforcing bars in concrete have been evaluated by carrying out single pullout and double pullout tests. In extended single pullout tests, slip measurements were made while tensile force was applied to reinforcing bars embedded in concrete. In double pullout tests, 20 cycles of load were applied at levels of steel stress between zero and 0·5 times characteristic steel strength. Strains were measured by electrical resistance strain gauges glued inside the bars. Both epoxy-coated and uncoated bars were used in the investigation, to obtain comparative results. The strain gradient along the bar was found to be less for the coated reinforcement. In general, the epoxy coating was found to increase slip in bond and thereby reduce the bond performance of coated bars.     

结构陶瓷的高温疲劳强度衰减理论

提出了陶瓷材料疲劳强度衰减理论并由此导出了各种疲劳关系式。建立了疲劳基本方程ｄσ＿ｒ／ｄ＿ｉ＝一Ａσ（ｔ）￣ｎｔ￣（－ｍ），得出了疲劳寿命公式Ｔ＝Ｍ（σ＿０－σ）／Ａσ￣ｎ（静疲劳时Ｍ＝１，连续增载疲劳时Ｍ＝ｎ＋１，循环疲劳时Ｍ＝（ｎ＋１）／（１＋Ｒ＋Ｒ￣２＋……＋Ｒ￣ｎ），逐级加载时，并导出不同疲劳方式下疲劳寿命间的关系。同时，用多种Ｓｉ＿３Ｎ＿４材料在高温中作了论证试验，结果与理论一致。     

ADS expert

ADS Expert is an integrated system that (a) provides suggestions about suitable optimization algorithms for a particular structural optimization problem, (b) it offers explanations and guide lines, in the form of hypertext, that refer to the optimization strategy, optimizer and one dimensional search method, (c) it produces the required gradients for the objective function and the constraints using symbolic differentiation, (d) establishes a direct linking with ADS routines and (e) it monitors the evolution of the optimization process. The system can be used as an educational tool for structural optimization and as an efficient integrated system for small to medium size optimization problems for which the objective function and the constraints are given in the form of explicit functions of the design variables. The system is a Windows application and runs quite satisfactorily on PCs.     

变结构变参数设计方法及其在机械CAD中的应用

提出了一种新颖的机械结构设计思想－变结构变参数设计方法，并结合实例，阐述了变结构变参数设计的概念、原则、实施措施和意义。由此对Ｉ－ｄｅａｓ软件包进行了二次开发，编制了发动机曲轴专用ＣＡＤ软件程序，并用某型号发动机曲轴进行了验证。     

小高层剪力墙结构开洞设计探讨

小高层建筑需通过剪力墙开洞(结构开洞)降低侧向刚度,本文对开洞部位以及墙肢和连梁设计提出一些看法,供设计人员参考。     

Strength of Metals at High Strain Rates

Results of metal testing in impact tension–compression and indentation are analyzed. As the analysis of these data demonstrates, the strength of metals increases greatly with strain rates and at moderate indentation rates. At high indentation rates, a decrease in the specific energy (per unit volume of a displaced material) necessary for the formation of a conical cavity was observed. The account of the effects of viscosity, temperature increase upon plastic deformation and its localization can be used to explain the above phenomena.     

弹药包装冲击强度试验方法的改进研究

介绍一种新的弹药包装冲击强度试验方法，应用该试验方法可以防止冲击强度试验时出现与期望值相反的现象。     

The concept of an endurance limit for adhesive joints

The effect of cyclic stressing on the strength of single lap adhesive joints has been studied and a considerable reduction in strength observed when the maximum stress exceeds about 40% of the ultimate tensile strength, but whether or not a true endurance limit exists is not proven. Fallacies are shown in some of the techniques which have been proposed for studying the fatigue behaviour of adhesive joints.