高层建筑损伤识别中的补偿算法

本文在已有研究工作的基础上，提出了处理激励测量信息不完备情况下的补偿算法。此方法主要针对高层建筑动力检测中强迫激励的情况，是一种基于时域的识别方法，该方法实际上是利用客观工程实际中结构系统激励所具有的物理持征作为识别计算的辅助条件，来解决测量信息的不完备性问题。算例分析表明了该方法的可行性。     

新型细粒煤分选设备的研究及应用

提出了一种新的细粒煤分选设备,主要介绍了它的结构模型、数学模型、动力学分析以及在贵州老屋基、孝义东兴、山西五阳、黑龙江七台河矿务局等洗煤厂中在煤泥脱水回收作业中的应用,取得了较好的效果。尤其用于简易选煤厂,从煤泥水中回收低灰精煤,既解决了环保污染问题,又取得了较高的经济效益,因而倍受欢迎。     

三峡永久船闸结构缝渗漏处理技术

在三峡永久船闸结构缝处理过程中，认真分析了结构缝渗漏的原因，通过止水检查槽进行压水检查，确定了渗漏部位。结合渗漏具体情况，采取了结构缝表面嵌填止水材料和廊道周边止水检查槽灌浆相结合的处理方法。在实施过程中，采用了多种新材料和新工艺，取得了良好的效果。     

结构陶瓷的空蚀性研究

利用转盘装置测量了ZrO2、Si3N4和Al2O3／Ti(NC)等陶瓷材料受到水的空蚀破坏的体积损失,通过SEM观察和XRD分析,探讨了微观结构和抗空蚀性能的关系。     

Solubility of amaranth seed proteins in sodium sulphate and sodium chloride: the main factor in quantitative extraction for analysis

Nitrogen was extracted more efficiently from amaranth seed with 0.04 M Na₂SO₄ (5% w/v) than with either 0.09 M or 0.17 M NaCl (5% or 10% w/v), despite both solutions having the same ionic strength (μ= 1). Solubility of saline soluble proteins (albumin ± globulin) was very poor in either water or 1M NaCl, but increased in 0.4M NaCl at alkaline pH between 7 and 10. Globulins were very soluble in 0.4M NaCl at a pH 9. Albumin was the main storage protein. Saline soluble proteins formed very weak gels.     

复合材料压缩破坏模式的缺陷敏感性

本文基于弹塑性分叉理论研究单向纤维增强复合材料的压缩破坏模式和压缩强度对缺陷的敏感性问题。对于常见复合材料,所得结论是:无缺陷或者小缺陷情况的破坏模式为倾斜破坏带;大缺陷情况的破坏模式为水平破坏带;形成水平破坏带的压力值小于形成倾斜破坏带的压力。     

Evaluating Liquefaction Strength of Partially Saturated Sand

A method is presented for evaluating the liquefaction strength of partially saturated sand using the compression wave velocity (P-wave velocity), a new indicator of saturation. Based on laboratory test results, an empirical correlation that relates the liquefaction strength with the pore pressure coefficient B is firstly proposed. The strength is defined as the cyclic stress ratio required to cause liquefaction at a specified number of cycles. With the aid of a theoretical relation between B and the P-wave velocity, an explicit correlation of more interest is then established between the liquefaction strength of sand and its P-wave velocity. A comparison of the predictions using this explicit correlation with laboratory measurements shows a satisfactory agreement. The significance of this method lies in that it makes it possible to evaluate the liquefaction strength of sand as affected by saturation through the measurement of P-wave velocity, which can be made not only in the laboratory but particularly in the field.     

一种高并行度的H.264帧内预测器的VLSI设计

分析了帧内预测的17种模式,对于每个4×4大小块的16个像素点的不同模式的预测公式之间的相同运算,采用数字强度缩减的方法去除计算的冗余,提出了一种高并行度的帧内预测器,可以每个时钟周期处理16个像素点的预测值。基于SMIC0.18μm工艺,用verilog对该设计进行了VLSI实现,综合后的电路的关键路径最大时延为10ns,电路规模不超过1.4万门,数据吞吐率可以达到1600Msamples/s。从实现结果来看,与采用可重构方法的设计相比,该设计在相同的并行度下减小了电路面积,简化了控制逻辑。     

Suppression of void coalescence in thermal aging of tin-silver-copper-X solder joints

Addressing the potential for drop impact failure of Pb-free interconnects, the shear ductility after extensive aging of Sn-Ag-Cu (SAC) solders has been improved radically by Co or Fe modifications. Several other SAC+X candidates (X=Mn, Ni, Ge, Ti, Si, Cr, and Zn) now have been tested. Solder joint microstructures and shear strength results show that new SAC+X alloys also suppress void formation and coalescence at the Cu (substrate)/Cu₃Sn interface (and embrittlement) after aging at 150°C for up to 1,000 h. Microprobe measurements of 1,000 h aged samples suggest that Cu substitution by X is usually accentuated in the intermetallic layers, consistent with X=Co and Fe results.     

Cyclic strength of parts with overlapping zones formed by roller burnishing

The authors study residual stresses in and cyclic strength of shaft with overlapping zones formed during roller burnishing. The most significant decrease in fatigue strength is shown to occur in the presence of an overlapping zone with the areas arising due to a lowered roller burnishing pressure in the second pass. __________ Translated from Problemy Prochnosti, No. 3, pp. 144–148, May–June, 2006.