裂纹对石墨烯拉伸力学性能影响的数值仿真

为研究裂纹对石墨烯力学性能的影响,以锯齿型石墨烯为研究对象,基于分子动力学方法,采用Tersoff势函数分析裂纹长度对石墨烯拉伸力学性能的影响以及含有裂纹的石墨烯在不同应变率下的拉伸变形破坏过程.结果表明,裂纹长度的增加大大减小石墨烯的抗拉强度和抗拉应变,对弹性模量有一定影响;裂纹降低石墨烯的抗拉应变对应变率的敏感性,但对于含有裂纹的石墨烯,仍可以增大加载速率来提高石墨烯的抗拉性能.     

AN EXPERIMENTAL-NUMERICAL METHOD FOR MEASURING CRACK PROPAGATING VELOCITIES UNDER STRESS WAVE LOADING

An experimental-numerical method for measuring dynamic crack propagating velocities under stress wave loading is established in this paper. The experiments of the three-point bend specimen are done on the improved Hopkinson bar. Deflection of loading point, dynamic load and instantaneous crack length are measured, then crack propagating velocities are calculated. Experiments on 40Cr steel show that the results given by this method have a good agreement with that obtained by the resistance fracture gage method. Therefore this method is feasible for measuring crack propagating velocities under high loading rate and will have wide application.     

冲天炉炉胆的(径向)胀裂问题及其防止措施

冲天炉炉胆径向胀裂问题，也是一道颇有难度的课题，本文提出：用平行四边形、竖立的梯形和微凹矩形三种炉壁断面作为防止措施。     

Carbon Aerogels as Electrode Material in Supercapacitors

Due to their large specific surface area and their high electrical conductivity carbon aerogels are promising materials for electrodes in electrochemical double-layer capacitors (supercapacitor). The carbon aerogels were made via pyrolysis of resorcinol formaldehyde aerogels. The latter were prepared by supercritical and subcritical drying as well. The important findings of our investigation were, that the highest capacities of 46 F/cm³ were measured for samples with a density of about 800 kg/m³ pyrolyzed at 800°C. Also it was shown that RF-gels with molar resorcinol/catalyst ratios 1000 or higher can be dried subcritically without cracking or significant shrinkage. Carbon aerogels derived from these RF-aerogels have a small mesopore surface area, however an especially large micropore area. They provide electrical capacities which are most suitable for their use in supercapacitors.     

Failure load prediction of structural adhesive joints : Part 2: Experimental study

The objective of this study was to determine how the fracture of adhesive joints depends on elastic beam parameters describing the adherends and the applied loads. The basic specimen geometry was the cracked lap shear joint constructed of aluminium alloy with various adherend and bondline thicknesses. Loads were applied in different combinations of bending, tension and shear to generate a failure envelope for each adhesive and specimen geometry. It was found that crack propagation for precracked specimens occured at a critical strain energy release rate but was also a function of the G_I/G_II ratio and the bondline thickness. The experiments also showed that the loads required to propagate a crack in a precracked specimen were always lower than the loads required to break the fillet. Hence, by treating uncracked joints as being cracked, where the fictitious crack tip is assumed to coincide with the location of the fillet, a conservative estimate of the failure load is obtained.     

基于3DMax技术的胡杨茎生长模拟

植物生长模拟研究,是利用计算机技术以可视化的形式描述植物的生长状态。本研究在综合国内外相关研究成果的基础上,以南疆胡杨茎为研究对象,通过对胡杨茎的生长因子及结构形态的研究,提出一种基于三维结构的胡杨茎生长模型,并运用3DMax技术建模,实现胡杨茎的生长形态的可视化。本研究能促进人们对胡杨生长过程的理解和感知,为分析胡杨结构功能关系、调控生长模式等提供重要参考。     

Simulation of the nitrogen balance in the soil and a winter wheat crop

A simulation model for winter wheat growth, crop nitrogen dynamics and soil nitrogen supply was tested against experimental data. When simulations of dry matter production agreed with measurements, nitrogen uptake was simulated accurately. The total amount of soil mineral nitrogen as well as the distribution of mineral nitrogen over the various soil layers were generally simulated well, except for experiments in which fertilizer was applied late in spring. In these experiments, applied nitrogen disappeared because it could not be accounted for by the model. Some explanations for this disappearance are briefly discussed.     

Slow stable crack growth in high density polyethylenes

The phenomenon of slow stable crack growth in polyethylene is investigated using notched specimens subject to constant load and the concepts of fracture mechanics. The effect of specimen geometry and dimension, the loading and the mode of loading on the applied stress intensity factor versus crack speed ($\text{K}{}_{\mathrm{c}}\text{-}\text{a}\text{?}$) curves has been studied to demonstrate that K_c is the controlling stress parameter for crack growth under suitable conditions. $\text{K}{}_{\mathrm{c}}\text{-}\text{a}\text{?}$ curves are obtained for a high density polyethylene homopolymer in distilled water and in a diluted detergent solution at four different temperatures. Results are also obtained for a much tougher medium density polyethylene copolymer whenever possible. Several mechanisms can be identified from the form of the $\text{K}{}_{\mathrm{c}}\text{-}\text{a}\text{?}$ curves. Two, in particular, have been observed but not explained before: (i) crack growth with a time dependence of 0.25, and (ii) the high $\text{K}{}_{\mathrm{c}}\text{-}\text{a}\text{?}$ slopes for crack growth in a tough copolymer. With the help of scanning electron microscopic studies of the fracture surfaces, (i) is postulated to be due to diffusion controlled void growth process and (ii) is considered to be the result of crack tip blunting effects. From the temperature dependence of crack growth, the activation energy of the diffusion controlled crack growth process is found to coincide with that of the x-relaxation process in polyethylene implying that diffusion controlled crack growth may be related to the motion of main chains in the polymer.     

Influence of modified forms of urea and nitrogen levels on weed growth and grain yield of lowland rice

The growth of weeds and their subsequent reduction of rice yield as affected by N source neem cake coated urea (NCU), dicyandiamide coated urea (DCU), rock phosphate coated urea (RPCU), urea supergranules (USG) and prilled urea (PU) was studied on a clay loam soil at Coimbatore, India. Experiments were conducted in northeast monsoon (NEM) 1981, summer 1982, and southwest monsoon (SWM) 1982 seasons.The crop was associated with eleven weed species, and the dominant weeds wereEchinochloa crus-galli, Cyperus difformis andMarsilea quadrifolia. The weed flora varied between seasons. Deep placement of USG reduced the dry weight of weeds in NEM and summer seasons at 60, 90 and 120 Kg N ha^–1 whereas it increased the dry weight at 60 and 90 but not 120 Kg N ha^–1 in SWM season. The dry weight of weeds decreased with increased N rates for all N sources during NEM and summer seasons. In SWM season, dry weight of weeds increased with increased N rates for all N sources except USG. The grain yield of rice was drastically reduced with the deep placement of USG at 60 but not 120 Kg N ha^–1 in SWM season. The differential effect of the N sources between seasons was due to the change of the weed flora. Dominance ofE. crus-galli during SWM season had greater influence on weed dry weight and grain yield of rice.Nitrogen uptake by weeds was frequently greater in unfertilized plots, particularly in NEM and summer seasons. In SWM season, the apparent fertilizer N recovery by weeds was high for USG. It decreased from 53% for 60 Kg USG-N ha^–1 to 4% for 120 Kg USG-N ha^–1.Contribution from the part of Ph.D. work of the first author at Department of Agronomy, Tamil Nadu Agricultural University, Coimbatore-641 003, Tamil Nadu, India.