Interfacial Microstructure and Mechanical Properties of Al/Mg Butt Joints Made by MIG Welding Process with Zn-Cd Alloy as Interlayer

Butt joints between Mg alloy AZ31 B and pure Al 1 060 sheets were produced via metal inert gas welding process with Zn-Cd alloy foil. Crack-free Al/Mg butt joints between AZ31 B Mg alloy and pure Al 1060 sheets were obtained. Intermetallic compound layer 1 and layer 2 had formed in fusion zone/Mg alloy and the average thickness of the layer 1 was about 50 μm. The intermetallic compound layer 1 consisted of Al12Mg17 and Mg2Si phases while layer 2 consisted of Al12Mg17, Mg2Si and Mg Zn2 phases. The crack started from the IMC layer at the bottom of the joint and propagated along the brittle IMC layer, then expanded into weld metal during the SEM in situ tensile test. The highest tensile strength of the dissimilar metal butt joints could reach 46.8 MPa and the effect ofinterfacial IMC layer on mechanical property of the joint was discussed in detail in the present study.     

岸吊焊缝裂纹分析与改进措施研究

从材料的焊接性能、焊接结构、焊条、预热与焊后热处理、焊接工艺参数等角度对岸吊胎架焊缝裂纹进行了分析,提出了改进措施,取得了良好的效果。     

CO2气体保护焊机操作注意事项

介绍了焊工在CO2气体保护焊机的安装、使用、维护保养及维修中的注意事项。     

Ni-Cr-Fe-Si-B合金涂层及铝青铜基体熔合区组织的研究

采用钨极氩弧焊方法在铝青铜基体上施焊了Ni—Cr-Fe-Si—B合金涂层，并运用金相显微镜、扫描电子显微镜及能谱分析了喷涂层、熔合区及热影响区的组织形貌和成分分布。结果表明，喷焊时，在涂层与基体界面两侧各组元均发生了明显的扩散，Cu、Ni组元间可相互取代，基体融合区组织的基本组成仍为α (α γ2)，但同时也形成了Cu2FeAl7、NiAl3等新相，且融合区组织细小，涂层与基体间为冶金态结合。     

基于I2C总线技术的等离子喷焊系统的研究

阐述了基于I^2C总线技术的等离子喷焊过程控制系统的设计原理，介绍了软硬件及接口设计技术。实践表明，采用I^2C总线技术，不仅使系统的芯片大大减少，系统的灵活性增强，而且提高了系统的抗干扰能力。     

Achievements and developing trend of welding technology in Chinese shipbuilding

ＡｃｈｉｅｖｅｍｅｎｔｓａｎｄｄｅｖｅｌｏｐｉｎｇｔｒｅｎｄｏｆｗｅｌｄｉｎｇｔｅｃｈｎｏｌｏｇｙｉｎＣｈｉｎｅｓｅｓｈｉｐｂｕｉｌｄｉｎｇ￥ＺＨＯＵＧｕｏｓｈｅｎｇａｎｄＷＵＪｉｎｇ（ＳｃｉｅｎｃｅａｎｄＴｅｃｈｎｏｌｏｇｙＢｕｒｅａｕｏｆＣＳＳＣ...     

ZL114铝合金激光--龟弧的复合焊接

设计了一种激光-电弧复合热源焊接ZL114合金的新工艺，并对焊后的试件进行了X光检测、抗拉强度和全相组织等实验。结果表明，该种新工艺对铝合全有良好的适应性和可行性，是焊接领域的一个趋势。     

逆变电源的可靠性及其提高途径

影响逆变焊接电源可靠性的因素是多方面的.如产品的设计和生产等各个环节.根据实践经验提出了解决可靠性问题的一些有效途径和方法.     

用PID控制弧焊逆变电源的试验研究

本文介绍了对逆变电源进行数字PID控制的原理和方法,分析了采样周期、PID参数及不同的焊接工况对控制特性的影响。试验表明,只要恰当地选择PID(或PI)参数,不仅能实现高精度的恒流控制,而且能使系统的动态性能显著提高。