小型机载激光通信系统设计与验证

针对空空宽带高速通信的需求，设计了小型化机载激光通信系统。仿真分析了300 km、2.5 Gb/s无线激光链路性能，并通过运动仿真台模拟机动环境测试了系统的跟踪与通信性能，其中粗跟踪误差为533.2 μrad(1σ)，精跟踪误差为3.6 μrad(1σ)，测试数据传输240 s，通信误码率为2.82×10-9。仿真与实验验证了该系统用于远距离空空无线激光通信的可行性。     

Performance investigation on a novel 3D wave flow channel design for PEMFC

Flow field structure can largely determine the output performance of Polymer electrolyte membrane fuel cell. Excellent channel configuration accelerates electrochemical reactions in the catalytic layer, effectively avoiding flooding on the cathode side. In present study, a three-dimensional, multi-phase model of PEMFC with a 3D wave flow channel is established. CFD method is applied to optimize the geometry constructions of three-dimensional wave flow channels. The results reveal that 3D wave flow channel is overall better than straight channel in promoting reactant gases transport, removing liquid water accumulated in microporous layer and avoiding thermal stress concentration in the membrane. Moreover, results show the optimal flow channel minimum depth and wave length of the 3D wave flow channel are 0.45 mm and 2 mm, respectively. Due to the periodic geometric characteristics of the wave channel, the convective mass transfer is introduced, improving gas flow rate in through-plane direction. Furthermore, when the cell output voltage is 0.4 V, the current density in the novel channel is 23.8% higher than that of conventional channel.     

Advances in the in vitro digestion and fermentation of polysaccharides

In vitro digestion models are widely used to study the structural changes, digestion and release of food components under simulated gastrointestinal conditions. As compared to the in vivo digestion tests, the in vitro digestion reflects the digestion and utilisation of food after ingestion and has the advantages of being time consuming, inexpensive, reproducible and free from moral and ethical restrictions. This study reviewed the current research studies on the in vitro simulated digestion of polysaccharides conducted in the last 5 years and focused on the oral, gastric and intestinal digestion models, with the aim of providing a basis for the further testing of changes in the content, structure and active ingredients of polysaccharides before and after digestion.     

A gradient boosting decision tree approach for insider trading identification: An empirical model evaluation of China stock market

Insider trading is a kind of criminal behavior in stock market by using nonpublic information. In recent years, it has become the major illegal activity in China’s stock market. In this study, a combination approach of GBDT (Gradient Boosting Decision Tree) and DE (Differential Evolution) is proposed to identify insider trading activities by using data of relevant indicators. First, insider trading samples occurred from year 2007 to 2017 and corresponding non-insider trading samples are collected. Next, the proposed method is trained by the GBDT, and initial parameters of the GBDT are optimized by the DE. Finally, out-of-samples are classified by the trained GBDT–DE model and its performances are evaluated. The experiment results show that our proposed method performed the best for insider trading identification under time window length of ninety days, indicating the relevant indicators under 90-days time window length are relatively more useful. Additionally, under all three time window lengths, relative importance result shows that several indicators are consistently crucial for insider trading identification. Furthermore, the proposed approach significantly outperforms other benchmark methods, demonstrating that it could be applied as an intelligent system to improve identification accuracy and efficiency for insider trading regulation in China stock market.     

澳大利亚“基于能力本位的评估”模式及对我国高职教育 质量评估的启 示

澳大利亚职业教育在全球享有较高的声誉,这与其坚持严格的"基于能力本位的评估"(competency based assessment, CBA)密不可分。介绍了澳大利亚CBA的内涵特征,并详细描述"准备评估、开发评估工具、开展评估、对评估结果进行评估"的CBA运作过程,关注评估工具的开发和后续常规系统性检查及完善,以期对我国的高等职业教育质量评估起到启示和借鉴作用。     

A three-dimensional surface measurement system implemented with Gaussian process based adaptive sampling

Self-adaptive surface measurements that can reduce data redundancy and improve time efficiency are in high demand in many fields of science and technology. For this purpose, a system implemented with Gaussian process (GP) adaptive sampling is developed. The non-parametric GP model is applied to reconstruct the topography and guide the subsequent sampling position, which is determined from the inference uncertainty estimation. A criterion is proposed to terminate the GP adaptive measurement automatically without any prior model or data of the topography. Experiments on typical surfaces validate the intelligence, adaptability, and high accuracy of the GP method along with the stabilization of the automatic iteration termination. Compared with traditional raster sampling, data redundancy is reduced and the time efficiency is improved without sacrificing the surface reconstruction accuracy. The proposed method can be implemented in other systems with similar measurement principles, thus benefitting surface characterizations.     

Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

面向草莓抓取的气动四叶片软体抓手研制

农林业中果蔬的自动化采摘需求日趋强烈,末端抓手是实现无损采摘的关键。传统的末端抓手以刚性结构居多,现有的各种柔性抓手也存在抓取力不足、包覆性不佳等缺点。本文以草莓的无损采摘为研究对象,提出将草莓外部轮廓曲线作为设计曲线,设计了一种新型气动四叶片软体抓手。首先,对软体抓手的结构做仿真优化,提出一种安全地附着在目标物表面的设想。然后,在进行草莓表面的最小破坏应力试验的基础上,测试了软体抓手的末端力,验证了其实现无损抓取的可行性。再次,利用动态捕捉技术,研究了软体抓手叶面的弯曲变形规律。最后,选择使用弧线型气体通道的软体抓手进行了草莓抓取测试,结果证明了气动四叶片软体抓手可以实现草莓的无损抓取,抓取成功率达90%,破损率为2%,表明所研制的四叶片软体抓手用于草莓抓取时具有良好的稳定性和实用性,可用于草莓采摘的末端执行器。本研究也可为其他易损果蔬的采摘技术提供理论基础和技术支撑。     

Development of autonomous monitoring and performance evaluation system of grid-tied photovoltaic station

This work aims to improve the existing monitoring systems MS for two grid-connected PV stations GCPVS of URERMS ADRAR, to eliminate its limitations. This improvement consists of developing an MS which is used for two PV stations with different configurations. This MS contains new LabVIEW-based monitoring software for visualizing real-time measured data and evaluating GCPVS performance. In addition, it illustrates the 2D and 3D real-time relationships of PV system parameters, which allow us to understand the dynamic behavior of PV system components. This developed monitoring software synchronizes also the various data acquisition units DAU of GCPVS, allowing simultaneous data access.To perform a reliable performance analysis and a comparative study of different GCPVS based on accurate measurements, the sensor's calibration is performed with its DAU. The MS autonomy is ensured by integrating developed PV-UPS. A graphical user interface is provided for the evaluation of PV-UPS performance.