Identification of gaps in mangrove forests with airborne LIDAR

Mangrove forests change frequently due to disturbances from tropical storms, frost, lightning, and insects. It has been suggested that the death and regeneration of trees in small gaps due to lightning may play a critical role in mangrove forest turnover; however, the large-scale quantification of spatial pattern and areas of gaps is lacking for investigating this issue. Airborne light detection and ranging (LIDAR) technology provides an effective way for identifying gaps by remotely obtaining direct measurements of ground and canopy elevations. A method based on an alternative sequential filter and black top-hat mathematical morphological transformation was developed to extract gap features. Comparison of identified gap polygons with raw LIDAR measurements and field surveys shows that the proposed method successfully extracted gap features in mangrove forests in Everglades National Park. There are 400–500 lightning gaps per square kilometer in mangrove forests at the study sites. The distribution of gap sizes follows an exponential form and the area of gaps with sizes larger than 100 m² account for 55–61% of the total area of gaps. The area of gaps in the mangrove forest in Everglades National Park is about 4–5% of the total forest area and the average gap formation rate is about 0.3% of the total forest area per year, indicating that lightning gaps play an important role in mangrove forest dynamics.     

A novel open-loop high-speed CMOS sample-and-hold

A new open-loop high-speed CMOS sample-and-hold is presented. Based on new method for further reduction of voltage-dependent charge injection, a new CMOS sample-and-hold was designed. Simulation results confirm the effectiveness of this method. Over 10 dB improvement in signal-to-noise ratio, compared to the signal-to-noise ratio of conventional bottom plate sampling S/Hs was achieved with this method. A comparison between newly designed S/H and the bottom-plate sampling S/H is presented.     

薄板坯连铸连轧工艺对铌微合金化高强度钢组织和性能的影响

首先建立薄板坯连铸连轧工艺的试验室模拟技术，并运用该模拟技术，研究薄板坯连铸连轧工艺(CSP)和传统板坯再加热工艺(TRP)两种工艺对铌微合金化高强度钢的显微组织和力学性能的影响。研究结果表明：CSP钢的晶粒细化效果不如TRP钢，两者的平均铁素体晶粒尺寸分别为8．17μm和6．30μm。在CSP试验钢板中铌的析出量较大，特别是在铁素体中细小颗粒的铌的析出物较多，沉淀强化效果较强。CSP试验钢的σ0.5和σb分别较TRP工艺低约40MPa和约25MPa，同时其低温冲击韧性较好，FATT温度较低。     

锌基合金模具的应用及探讨

本文分析了锌基合金模具制造及使用过程中容易出现热裂、翘曲、收缩的问题，并提出了解决这些问题的措施。     

Data mining of resilience indicators

In recent years, the Asia-Pacific region has experienced several financial setbacks, including speculative attacks in 1998 and the SARS outbreak in 2003. Financial stresses of this nature are unanticipated, and not all of the dangers can be predicted by the examination of market information and macroeconomic indicators. The Early Warning System (EWS) that has been adopted by the International Monetary Fund may not be able to predict future financial crises for all possible scenarios, because shocks come in many different forms. To supplement the EWS, this paper proposes a data mining framework to measure the resilience of an economy. The resilience framework does not predict a crisis, but rather assesses the current state of health of an economy and its ability to withstand a financial shock should one occur. The framework is based on a feedback system consisting of two stages. The first stage assigns a resilience score to each economy based on a fuzzy logic scoring scheme that is built on the ambiguous reasoning of experts. The second stage uses the classification tree approach to estimate thresholds for each economic indicator, and examines the quality of the fuzzy score. The result from the second stage is then passed back to the first stage as feedback. The final result is obtained when the feedback system reaches its equilibrium state. The proposed resilience framework is applied to the external-sector and the public-sector economies of several countries to illustrate its applicability.     

节能降耗提高矿山效益

节能降耗是每一个矿山提高经济效益的有效途径。我们采取提高球磨机处理能力，降低单耗；利用“分时计价”政策，采用“避峰作业”；使用新设备等措施节能降耗，提高矿山经济效益。     

Line balancing in a just-in-time production environment: balancing multiple U-lines

The introduction of multiple, independent production lines has helped many firms to increase their production flexibility, provide for redundancy when equipment breaks down, reduce idle time and labor costs, and achieve many other benefits. This paper introduces and formalizes the multiple U-line balancing problem. Optimal solution methodologies are provided for Type I (minimize the number of stations for a given cycle time), Type II (minimize the cycle time for a given number of stations), and cost-minimization line-balancing problems. A branch-and-bound algorithm is also developed for the situation in which equipment requirements are dependent on the line configuration and the task assignment to stations. Computational results indicate that the greatest benefit of exploiting multiple lines occurs for smaller cycle-time problems that require higher output.     

网络环境下高校图书馆期刊资源建设与发展

本文根据电子期刊的定义、特点及图书馆期刊工作所需要面对的问题，就高校图书馆网络环境下期刊工作的设施规划、资料收集、信息开发及读者培训等多方面内容进行了简单探讨，并就如何应对网络环境下图书馆期刊工作的变化提出建议。     

钼酸盐阻燃抑烟剂研发现状

简要地叙述了钼酸盐类阻燃抑烟剂 ,如八钼酸铵、钼酸锌、钼酸钙、钼酸钴和三氧化钼等阻燃抑烟剂的研发现状     

ZJ510L-B汽车用高强度热轧板的试制

珠钢150t电弧炉-LF(VD)-CSP(紧凑式带材生产)流程试生产的5～8mm ZJ510L-B(0．16C--1．22Mn)汽车用高强度热轧板的铁素体晶粒尺寸为6．0～9．2μm，带状组织为1．5～2．5级，强度极限σb562～610MPa，延伸率δ5 32．0％～38．6％。文中还分析和提出了带状组织的形成原因和改进措施。