Development of temperature compensated high elongation resistance strain gauges for use up to 250°C

The paper describes the development and evaluation of temperature compensated high elongation resistance strain gauges for use from room temperature to 250°C. These gauges could be temperature-compensated on steels with coefficient of thermal expansion α = 11 ppm/°C. Thermal output within 250°C was about 1 μm/m/°C and maximum standard deviation of 5 gauges was 34 μm/m. Strain limit was > 4% at room temperature and at 250°C. Gauge factors of different strain ranges at R.T. and at 250°C are tabulated. Some applications are stated.     

Heat loss and thermoelectric generator design

With the object of evaluating its importance to thermoelectric generator design, heat loss is introduced into the standard thermoelectric generator design theory. The theory for both the constant hot and cold junction temperatures model and the constant heat input model are so modified. The modification is first order and, therefore, is limited to small leg heat-transfer coefficients. Numerical results using representative properties show that significant differences can exist between the optimum geometry and performance of a generator idealized as lossless and those of a generator designed by the modified theory. The largest differences occur with the constant heat input model.     

Sidechain liquid crystal polymers

Research has continued in the field sidechain liquid crystal polymers over recent years, but it is becoming clearer that this research is being directed away from the traditional technology areas of electro-optic devices and researchers are developing new and exciting applications for this novel state of matter.     

提高钻杆接头冲击功的工艺方法

针对石油钻井关键产品高强度钻杆接头的使用要求,在保证强度指标要求非常高的前提下,研究摸索增加高温正火后再调质的工艺方法,以改善接头材料原始微观带状组织和纤维结构,细化晶粒,提高钻杆接头的冲击功,使该产品力学性能达到API标准的要求。     

A NEW ELECTROMAGNETIC IMAGING SCHEME

ＡＮＥＷＥＬＥＣＴＲＯＭＡＧＮＥＴＩＣＩＭＡＧＩＮＧＳＣＨＥＭＥ①ＺｈａｎｇＲｏｎｇｆｅｎｇ，ＨｅＪｉｓｈａｎＣｏｌｅｇｅｏｆＲｅｓｏｕｒｃｅ，ＥｎｖｉｒｏｎｍｅｎｔａｎｄＣｉｖｉｌＥｎｇｉｎｅｒｉｎｇ，ＣｅｎｔｒａｌＳｏｕｔｈＵｎｉｖｅｒｓｉｔｙｏ...     

High cycle fatigue behaviour of Ti–6Al–4V alloy at elevated temperatures

High cycle fatigue behaviour of Ti–6Al–4V alloy was studied at 623 K and 723 K. Fatigue strength decreased at elevated temperatures compared with at ambient temperature. In the short life regime, fatigue strength was lower at 723 K than at 623 K, but in the long life regime it was nearly the same at both temperatures. At elevated temperatures, cracks were generated earlier at applied stresses below the fatigue limit at ambient temperature, indicating lowered crack initiation resistance. Small cracks grew faster at elevated temperatures than at ambient temperature, which became more noticeable with increasing temperature. After allowing for the elastic modulus, small cracks still grew faster at elevated temperatures.     

纺牵—步法中粗旦丙纶长丝沸水收缩率初探

在纺牵联合一步法纺丝机上研究了丙纶切片的熔融指数对纤维沸水收缩率的影响，发现熔融指数高的切片，其纤维的沸水收缩率变化大。沸水收缩率随热定型的温度升高而下降。沸水收缩率可根据用户提供中心值（Ｍ）通过实验确定，一般以Ｍ±１．５为宜。     

浅谈一次盐水的工艺指标控制

介绍了一次盐水的各项工艺指标对生产的影响以及稳定控制这些指标的方法，强调了在生产中控制好一次盐水的工艺指标是影响产品质量及离子交换膜使用寿命的关键。     

窑炉用热电阻、热电偶智能温度测量板的设计

温度是影响陶瓷烧成质量的关键因素,介绍了一种适用于测量各种窑炉不同部位温度的智能温度测量板,由于该系统在不同的测温部位分别采用了热电阻和热电偶,克服了一般测温系统在连接不同的测温传感器需要更换不同的测温模板、成本高、使用不方便等不足,并具有适用性强、测温精度高等优点。