45号钢二次枝晶臂间距与冷却速度的关系

本文利用可控平均冷却速度的单向凝固实验炉测定了４５号钢在不同平均冷却速度下的冷却曲线，由此得到其在凝固期间的平均冷却速度Ｒ，相应地测量了不同平均冷却速度下试样的二次枝晶臂间距Ｓ２，通过回归，得到了如下关系式：Ｓ２＝７２７Ｒ－０．４１，并将引式成功地应用于实际生产中。     

Measurement of the tunnel rate in SIS' tunnel junctions as function of bias voltage

Cryogenic detectors with superconducting tunnel junctions can provide an energy resolution improved by at least one order of magnitude compared with standard semiconductor detectors. While the detection principle was already demonstrated many years ago, the past years were dedicated to the transition from the laboratory sample to practical detectors. Our most favored detector design gives rise to tunnel junctions with electrodes of unequal energy gaps. In such hetero tunnel junctions bias conditions can be established which cause a negative signal current. We report the experimental verification of this effect, and we discuss the yield of charge signal of cryogenic detectors based upon superconducting tunnel junctions.     

Experimental evaluation of the strength distribution of E-glass fibres at high strain rates

A bimodal Weibull distribution function was applied to analyse the strength distribution of glass fibre bundles under tensile impact. The simulation was performed using a one-dimensional damage constitutive model. The results show that there were two concurrent flaw populations in the fracture process. The regression analysis using the bimodal Weibull distribution function was in good agreement with experiment.     

Paste Residence Time in a Spouted Bed Dryer. II: Effect of Spout Operational Conditions

Residence time distributions for an aqueous solution of 10% sodium chloride in a spouted bed dryer of inert particles were determined using the stimulus-response technique. Glass and polyethylene beads with diameters 2.6 and 3.4 mm were used as inert bodies in a cylindrical column of 14.0 cm diameter and 60° conical base. The effects of inert bodies load, air, and paste flow rates on the mean residence times and RTD were determined following 2³ factorial designs. The RTD could be correlated to the perfect mixing cell model with R² varying from 0.8684 to 0.9815. The mean residence times in CSBD varied from 10.8 to 13.9 and 10.7 to 13.3 min for glass and polyethylene beads, respectively. For both inert particles, mean residence times increased with bed height and decreased with paste feed rates. Also, terms of interaction among the factors were significant in some cases, showing a complex behavior of paste residence times. Equations obtained by response surface regression could predict mean residence times on glass and polyethylene beads with deviations lower than ±10%.     

油田单井平均日产油量经济极限确定方法

从f(n,t)曲线的研究出发,得到了求解油田单井平均日产油量经济极限值的数学方程式,介绍了用曲线交汇法求解的过程,分析了油田月递减余率和原油销售价是影响油田单井平均日产油量经济极限的主要因素。该方法在油田开发调整方案的编制和油田开发规划部署工作中将起到一定的作用。     

Mycological and physical parameters for selecting suitable packaging material for pre- and post-irradiation storage of cereal grains in Ghana

Owing to the rough warehouse handling of storage sacks in tropical areas in Africa, a suitable storage sack should not support de novo growth of fungal spores because this would reduce the tensile strength of the packaging material and act as a springboard for infecting grain contents. This paper reports the effect of activity of saprophytic fungi on the tensile strength of jute and woven polypropylene sacks. New woven polypropylene sacks carried lower levels of fungal spores (1.3×10¹ cfu/72 cm²) than jute sacks (3.0×10³ cfu/72 cm²). The natural mould penetration and growth was examined on sections (4×5 cm) of both jute and woven polypropylene after previous incubation at relative humidities of 55, 60, 65, 70, 75, 80, 90 and 95% for 10 weeks by placing them on Sabouraud's Agar. There was a significant difference (P = 0.05 level of significance) between the higher penetration of mould growth on jute sacks and that obtained on woven polypropylene sacks. Saprophytic fungi (Aspergillus candidus, A. flavus, A. fumigatus, A. niger, A. japonicus, A. parasiticus, A. ustus, Fusarium oxysporium, F. moniliforme, Penicillium verucosum var. cyclopium, Rhizopus oryzae and Trichoderma viride) isolated from jute sacks reduced tensile strength, measured by an Instron Model 1026, by 50–75% after 10 weeks at 90% R.H. Same fungal species on woven polypropylene sacks did not alter the tensile strength. Woven polypropylene sacks did not absorb moisture whilst the moisture content of jute sacks increased by 5.3–6.0% in 10 weeks at 90% R.H. with concomitant increase in mould and yeast counts by 1–2 log cycles. Evidence is presented to show that there was a positive correlation between the final mycoflora on jute sacks and loss in tensile strength. No correlation, however, was found between the total aerobic bacteria on jute sacks and the concomitant reduction in tensile strength. Fungi therefore play a major role in the reduction of tensile strength of jute sacks. Sterilization by gamma irradiation (8.0 kGy) of jute and woven polypropylene sacks did not affect their intrinsic tensile strength. Woven polypropylene sacks therefore have many microbiological and physical advantages over the traditional jute sacks to merit their use for grain storage in tropical areas like Ghana.     

电子辐照加速器大功率工频高压电源

文章介绍目前两种用于烟气脱硫加速器的不同形式直流高压电源，分析了它们各自的特点。针对它们存在的不足之处，提出了一种全新的倍压型桥式整流线路，并对此线路进行了理论推导和计算机模拟仿真。     

Drying Characteristics of Barley Grain Dried in a Spouted-Bed and Combined IR-Convection Dryers

A study was performed to determine the drying characteristics and quality of barley grain dried in a laboratory scale spouted-bed dryer at 30, 35, 40, and 45°C and an inlet air velocity of 23 m/s^-1, and in an IR-convection dryer under an infrared radiation intensity of 0.048, 0.061, 0.073, and 0.107 W cm^-2 at an air velocity of 0.5 m/s^-1. The results show that the first, relatively short, phase of a sharp decrease in the drying rate was followed by the phase of a slow decrease. The time of barley drying depended on temperature of inlet air in a spouted-bed dryer and on radiation intensities in an IR-convection dryer. Barley drying at 45°C in a spouted-bed dryer was accompanied by the lowest total energy consumption. The average specific energy consumption was lower and the average efficiency of drying was higher for drying in a spouted-bed dryer. The effective diffusivities were in the range 2.20-4.52 × 10^-11 m² s^-1 and 3.04-4.79 × 10^-11 m²/s^-1 for barley dried in a spouted-bed and in an IR-convection dryer, respectively. There were no significant differences in kernel germination energy and capacity between the two drying methods tested.     

Phase separation studies in RIM polyurethanes catalyst and hard segment crystallinity effects

Polyurethanes were prepared from pure 4,4′-diphenylmethane diisocyanate (MDI), 1,4-butane diol (BDO) or 1,2-ethane diol (EDO) and α,ω-hydroxyl poly(propylene oxide) (PPO) by reaction injection moulding (RIM). Hard segment (MDI + BDO or EDO) level was 45–50 wt%. The PPO had about 20% ethylene oxide copolymerized in at the chain ends to provide 80% primary OH end groups. M_n was varied from 2000 to 4000. Dibutyl tin dilaurate catalyst and mould temperature were varied. Dynamic mechanical, wide-angle X-ray, differential scanning calorimeter, molecular weight and tensile elongation measurements were made on the RIM polyurethanes. At low reaction rates (low catalyst or temperature) highly crystalline, well phase separated but low molecular weight polymers were produced. At high catalyst or temperature levels more poorly phase separated but high molecular weight, tough polymers resulted. Higher M_n PPO gave better phase separation and EDO gave higher melting temperatures. Preventing hard segment crystallinity by substituting asymmetric MDI or glycols resulted in phase compatibility.     

Studies on chitin 3—effect of coagulants and annealing on the preparation and the properties of chitin membrane

Chitin membrane was prepared by casting a N,N-dimethyl acetamide, N-methyl 2-pyrrolidone and lithium chloride (DMA-NMP-LiCl)solution of chitin and coagulating with several media. The effect of the coagulants on membrane formation was studied. 2-Propanol was found to be more favourable than methanol, ethanol, acetone and mixtures of 2-propanol and water. The membrane obtained in 2-propanol was subjected to annealing. Annealing made the membrane dense and strong. The tensile strength of the membrane annealed at 145°C for 2hr was about twice that of an unannealed membrane. The solute permeability of the annealed membranes was lower than that of the original one. These phenomena could be clearly interpreted in terms of crystallinity.