聚合物-金属界面相形貌的研究

环氧树脂在 Al 合金表面生成纤维状的界面相结构,其形成、发展和特征与树脂的体系、交联反应条件以及 Al 合金的表面状态有关。环氧树脂的基础相为颗粒状的超结构组织。聚合物界面相的力学破坏表现为纤维体的拉伸、变形和断裂,而基础相在纯剪切受力时出现在45°方向的裂纹,并发展导致连接层的破坏。     

Formation of layered structure on bismuth-borate glass surface

X-ray diffraction analysis shows that the transformation during heat treatment from amorphous to crystalline phases of bismuth-borate glass samples takes place in sequences. After a short heat treatment, 5 min at 550 °C, a layered structure with a preferred orientation of crystallites on the surface is observed. After a long heat treatment, 8 h at the same temperature, normal polycrystalline bulk samples are obtained.     

A new iterative order reduction (IOR) method for eigensolutions of large structures

Order reduction is a computationally efficient method to estimate some lowest eigenvalues and the corresponding eigenvectors of large structural systems by reducing the order of the original model to a smaller one. But its accuracy is limited to a small range of frequencies that depends on the selection of the retained degrees of freedom. This paper proposes a new iterative order reduction (IOR) technique to obtain accurately the eigensolutions of large structural systems. The technique retains all the inertia terms associated with the removed degrees of freedom. This hence leads to the reduced mass matrix being in an iterated form and the reduced stiffness matrix constant. From these mass and stiffness matrices, the eigensolutions of the reduced system can be obtained iteratively. On convergence the reduced system reproduces the eigensolutions of the original structure. A proof of the convergence property is also presented. Applications of the method to a practical GARTEUR structure as well as a plate have demonstrated that the proposed method is comparable to the commonly used Subspace Iteration method in terms of numerical accuracy. Moreover, it has been found that the proposed method is computationally more efficient than the Subspace Iteration method. Copyright © 2003 John Wiley & Sons, Ltd.     

真空制盐蒸发结晶器的设计与实践

真空蒸发制盐外热式强制逆循环轴向出料蒸发结晶器，经多个厂家生产应用实践证明是成功的，具有生命力的。这种新型结构，作为一项新技术新设备应加强研究，总结提高，推广应用。不断完善。文章从流体力学、结晶机理角度要求，到具体工程设计参数和材质选用。论述了该罐的特点。     

A Bayesian propensity score adjustment for latent variable modeling and MCMC algorithm

The estimation of the differences among groups in observational studies is frequently inaccurate owing to a bias caused by differences in the distributions of covariates. In order to estimate the average treatment effects when the treatment variable is binary, Rosenbaum and Rubin [1983. The central role of the propensity score in observational studies for causal effects. Biometrika 70, 41-55] proposed an adjustment method for pre-treatment variables using propensity scores. Imbens [2000. The role of the propensity score in estimating dose-response functions. Biometrika 87, 706-710] extended the propensity score methodology for estimation of average treatment effects with multivalued treatments.However, these studies focused only on estimating the marginal mean structure. In many substantive sciences such as the biological and social sciences, a general estimation method is required to deal with more complex analyses other than regression, such as testing group differences on latent variables. For latent variable models, the EM algorithm or the traditional Monte Carlo methods are necessary. However, in propensity score adjustment, these methods cannot be used because the full distribution is not specified.In this paper, we propose a quasi-Bayesian estimation method for general parametric models that integrate out the distributions of covariates using propensity scores. Although the proposed Bayes estimates are shown to be consistent, they can be calculated by existing Markov chain Monte Carlo methods such as Gibbs sampler. The proposed method is useful to estimate parameters in latent variable models, while the previous methods were unable to provide valid estimates for complex models such as latent variable models.We also illustrated the procedure using the data obtained from the US National Longitudinal Survey of Children and Youth (NLSY1979-2002) for estimating the effect of maternal smoking during pregnancy on the development of the child's cognitive functioning.     

论我国大学不良竞争的形成及控制

大学在办学资源、办学过程、办学质量、办学形象的竞争中出现大量的不良倾向。大学的不良竞争是由于政府主导资源配置、资源和制度供给不足、大学系统重构等因素导致。必须通过控制主体、控制手段的转变和控制对象的发展形成新的控制机制，以保证大学竞争的秩序化和规范化。     

Asymmetric Regulation System Fit for Chinese Telecom Market

After the new round of restructuring of Chinese telecom sector,it's pressing to formulate and implement asymmetric regulation policies so as to shape an effectively competitive market structure in a relatively short term.This paper reviewed the asymmetric regulation policies and practices carried out in foreign telecom market,and then according to the specific situations of Chinese telecom market,proposed the principles and corresponding policies for establishing an asymmetric regulation system fit for Chin...     

Structural study of cubic pyrochlores based on quantum mechanical simulation

In the ideal A₂B₂O₆O′ pyrochlore structure, the x-value of O atom position is a variable parameter. In Bi_1.5ZnNb_1.5−xTa_xO₇ (BZNT) cubic pyrochlores, the x-values alter with the different compositions of Nb/Ta. In this work, a series of initial models for BZNT were established by analyzing X-ray diffraction data. Then three structure modifying methods, including Rietveld refinement, Rietveld refinement with energy and geometry optimization based on quantum mechanics, were employed to obtain the precise models using Materials Studio. Moreover, the reflectivities of BZNT were computed by quantum mechanical simulation based on the refined models. Comparing the simulation results from different modifying models with the experimental results, it is found that Rietveld refinement with energy optimization is the most accurate method for BZNT pyrochlores. According to the simulation results, the different reflectivities correspond well with various x-values of O atom positions in BZNT pyrochlores.     

弹力竹节牛仔布织造工艺优化

介绍了弹力竹节牛仔布的生产工艺 ,同时对KT36 8剑杆织机织造该织物的工艺进行了优化研究     

有粘结预应力在252m地下室顶板中的应用

在总长度 2 5 2m的超长不设缝地下室顶板中 ,采用了预应力、设置后浇带等综合抗裂技术 ,并对有粘结预应力平板的设计理论、施工工艺、锚固体系及超长结构预应力损失控制和抗裂控制作了深入研究。