Characterization of microporous-mesoporous MCM-41 silicates prepared in the presence of octyltrimethylammonium bromide

MCM-41 silicates prepared in the presence of octyltrimethylammonium bromide either by a conventional method or by post-synthesis hydrothermal treatment were characterized by nitrogen adsorption in a wide range of relative pressure from 10^-6 to 1. Hydrothermally restructured samples were found to have lower BET surface areas, lower external surface areas and thicker silica walls than the non-treated sample. More importantly, in addition to their characteristic mesopores (ca. 3 nm), they were shown to have considerable amounts of micropores. The relative amount of micropores and mesopores was shown to be dependent on the treatment conditions. Thus, it is demonstrated that the postsynthesis hydrothermal restructuring is a convenient synthesis route to MCM-41 silicates with bimodal pore size distribution involving controllable amounts of microporosity. This revised version was published online in July 2006 with corrections to the Cover Date.     

Surface and subsurface products of the interaction of O2 with Ag under catalytic conditions

Polycrystalline Ag treated with O₂ at pressures up to 1 bar and at temperatures up to 920 K was examined by TDS. It was found that the peak commonly observed at 595±25 K and assigned to adsorbed atomic oxygen (O_a) is shifted to higher desorption temperatures with rising dosing temperatures. Since saturation of the uptake was not possible either, this peak was identified as dissolved atomic oxygen (O_d). The existence of a maximum for the O₂ uptake after exposure at 820 K was found. Hence, under conditions of formaldehyde synthesis ( 920 K) the ability of the catalyst to dissolve oxygen is near its maximum.     

A rapid test to measure performance,emission and wear of a diesel engine fueled with palm oil diesel

Results of performance, emission and tribological evaluations of palm oil methyl ester and its blends with conventional diesel in an automobile diesel engine test bed are presented. Polymerization and carbon deposits on the fuel injector were monitored. CO, CO₂, O₂, combustion efficiency and temperature of exhaust gases were also measured. Palm oil methyl ester and its blends have great potential as alternative diesel fuel. Performance and exhaust gas emission for palm oil methyl ester and its blends with conventional diesel are comparable with those of conventional diesel fuel. Palm oil methyl ester does not pose a severe environmental problem and will not deteriorate engine and bearing components.     

低密度泡沫玻璃的研究与应用

低密度泡沫玻璃是利用碎玻璃制造的一种气孔率大于90%的隔热保温材料,它具有强度高、导热系数小、吸水率低、不吸湿、耐腐蚀等特性,在潮湿环境下抗冻性能好,是一种优良的低温、超低温隔热保温材料。该产品用途广泛,所用的原材料简单易得,但生产工艺过程比较复杂,生产过程控制精度要求较高,容易产生各种缺陷而影响产品的质量。本文对低密度泡沫玻璃的生产工艺过程进行详细的分析研究,提出相应的措施,确保产品的低密度和高成品率,提高产品的性能,扩大产品的使用范围。     

MgO／Ni系梯度功能材料的设计与制备

对ＭｇＯ／Ｎｉ系梯度功能材料（ＦＧＭ），分别用实验和微观力学模型测定和计算了用于热应力缓和设计的各物性参数。讨论了两种结果之间存在差异的原因。用有限元方法模拟了制备过程中ＦＧＭ的热应力，得到ＭｇＯ／Ｎｉ系ＦＧＭ的综合设计准则。按设计结果进一步调整粉末工艺性质，成功地烧制出ＭｇＯ／Ｎｉ系ＦＧＭ。     

Preparations and properties of thermosensitive terpolymers of N‐isopropylacrylamide,sodium 2‐acrylamido‐2‐methyl‐propanesuphonate,and N‐tert‐butylacrylamide

Terpolymers based on N‐isopropylacrylamide, sodium 2‐acrylamido‐2‐methyl‐propanesulfonate, and N‐tert‐butylacrylamide were synthesized by free‐radical copolymerization with 2,2′‐azobisisobutyronitrile as an initiator. The lower critical solution temperatures (LCSTs) of the linear polymer aqueous solutions were determined by the measurement of the transmittance on UV at different temperatures. The influence of the polymer concentration, polymer composition, and ionic strength on the LCSTs of the linear polymers was investigated. The LCST decreased with increases in the hydrophobic monomer N‐tert‐butylacrylamide, polymer concentration, and ionic strength. The phase transition became sharp when the polymer concentration and ionic strength increased. Meanwhile, the crosslinked hydrogels were prepared with the same recipe used for the linear terpolymers, but a crosslinker was added to the reaction system. The swelling ratios of the hydrogels at various temperatures and salt solutions were determined. The hydrogels possessed both high swelling ratios and thermosensitivity. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Radiation-induced copolymerization of trioxane with tetrahydrofuran

Radiation-initiated copolymerization of solid trioxane (TOX) with tetrahydrofuran (THF) was investigated. The effects of radiation dose, THF concentration, and post-polymerization temperature and duration on copolymer yield and THF incorporation were studied. These results are compared with the results of TOX homopolymerization under identical conditions. Copolymer yield was lower than that of homopolymer. Only a fraction of charged THF entered into the polymer chain. THF content and radiation dose also altered the MW of the copolymer but it showed better thermal stability. The initial reaction rates of the copolymerization were determined and from these the activation energy was found to be 36.2 kcal mol^?1.     

Microstructure of solution-chlorinated polyethylene by 13C nuclear magnetic resonance

Solution-chlorinated polyethylene prepared by a modified method has been characterized using ¹³C nuclear magnetic resonance (n.m.r.) and differential thermal analysis (d.t.a.). The results show that the residual paraffin segments, melting point and crystallinity decrease rapidly with increasing chlorine content. The prepared polymer seems to have a homogeneous chlorine distribution.     

热处理前后丙烯腈／溴乙烯共聚纤维的热性能和阻燃性能研究

分析了热处理前后丙烯腈／溴乙烯共聚纤维的热性能与溴乙烯含量、升温速率或热处理时间的关系，并对纤维的阻燃性与溴含量或热处理时间关系进行了研究。结果表明，溴含量的增加或热处理时间的延长对热稳定性和阻燃性的提高有较大影响，而且经热处理后纤维的阻燃性与溴无关。