Effect of deposition conditions on the properties and annealing behavior of cold-sprayed copper

The deposition of copper by cold gas dynamic spraying has attracted much interest in recent years due to the capability to deposit low-porosity oxide-free coatings. However, it is generally found that as-deposited copper has a signicantly greater hardness, and potentially lower ductility, than bulk material. In this article, copper was deposited by cold spraying using helium as the driving gas at both 298 and 523 K. Evidence is presented indicating that the material sprayed at the lower temperature exhibits a lower dislocation density throughout the grain structure than the material sprayed at the higher temperature. The low stacking fault energy of copper restricts recovery during annealing, and thus microstructural changes during annealing only proceed once recrystallization begins. The material sprayed at low temperature (with the low dislocation density) exhibited recrystallization at annealing temperatures as low as 373 K with a corresponding reduction in hardness. However, the copper sprayed with helium at 523 K was resistant to annealing at temperatures up to 473 K where the dislocations in the structure prevented recrystallization. However, at higher temperatures, recrystallization did proceed (with corresponding reductions in hardness). The fracture behavior of the copper that was cold sprayed with helium at 523 K, both in the as-sprayed condition and following annealing, was measured and explained in terms of the annealing mechanisms proposed. The original version of this paper was published in the CD ROM Thermal Spray Connects: Explore Its Surfacing Potential, International Thermal Spray Conference, sponsored by DVS, ASM International, and HW International Institute of Welding, Basel, Switzerland, May 2–4, 2005, DVS-Verlag GmbH, Düsseldorf, Germany.     

解析参数对活性焦再生过程及再生效果的影响

 活性焦的热解析参数对再生活性焦的脱硫脱硝性能和机械强度至关重要。为了明确解析参数对活性焦再生过程和再生效果的影响规律,通过热解析试验探究活性焦硫残余比例、CO₂和CO生成量及再生活性焦脱硫脱硝性能随解析温度和解析时间的变化规律,继而明确适宜的活性焦热解析参数。结果表明,活性焦升温解析过程中,脱硫产物在317 ℃左右迅速分解,随后分解速率下降;在进入恒温解析阶段后脱硫产物分解速率先快速下降,而后进入缓慢解析状态。硫残余比例随恒温解析温度的升高而下降,在530 ℃下解析3 h可使脱硫产物完全解析;解析温度高于430 ℃后,活性焦表面的酚基、醌基、内酯基等含氧官能团分解量明显增加,并随恒温解析温度的升高而持续增加,分解所生成的CO和CO₂也随之大幅增加,这将使活性焦的孔隙结构进一步发展,继而不利于活性焦机械强度的保持;解析温度低于530 ℃时,硫残余比例随解析温度的升高而持续降低,使再生活性焦的脱硫脱硝性能持续提高;解析温度高于530 ℃后,含氧官能团分解量随解析温度的升高而持续增加,这将有利于提高活性焦表面SO₂氧化反应速率,继而使再生活性焦的脱硫性能持续升高,但酚基、内酯基等酸性含氧官能团的分解使再生活性焦对NH₃的吸附性能降低,进而使其脱硝性能降低。在兼顾再生活性焦脱硫脱硝性能、机械强度和生产效率等多方面因素时,430 ℃恒温解析3 h是相对较优的解析参数。在此解析条件下,再生活性焦的硫残余比例仅为1.8%,含氧官能团尚未发生大量分解,脱硫脱硝性能相对较为优良。     

地聚合物混凝土配比及力学性能研究

混凝土是巷道支护过程中的重要建筑材料,然而混凝土在巷道施工中常常出现质量问题,为了不影响正常生产,需要对其进行修补。地聚合物混凝土凝结时间快,早期强度高,界面结合能力强,耐高温性和抗冻性强,耐腐蚀性良好,具有用作修补材料的潜力。以粉煤灰和矿粉为原料,Na₂SiO₃溶液和NaOH为碱激发剂制备地聚合物胶砂,研究不同的碱激发剂模数（1.0、1.2、1.4）和掺量（10%、15%、20%）对不同龄期胶砂力学性能的影响。结果表明：当碱激发剂模数为1.2,碱掺量为15%时,胶砂强度达到最大值。设计正交试验,研究了不同水胶比（0.45、0.50、0.55）、粉煤灰掺量（30%、50%、70%）和砂率（30%、35%、40%）对不同龄期地聚合物混凝土的工作性能和力学性能的影响。结果表明：粉煤灰掺量对抗压强度影响最为显著,水胶比次之,而砂率对强度发展几乎没有影响。最优的配合比为水胶比为0.50,粉煤灰掺量为50%,砂率为35%。     

离心泵性能参数的自动测定和自动控制

通过将计算机技术应用于离心泵性能参数的研究，实现了离心泵性能参数的自动测定和自动控制。     

Determination of the solubility parameter of poly(ethylene oxide) at 25°C by gas-liquid chromatography

The solubility parameter of poly(ethylene oxide) at 25°C has been determined using the method developed by DiPaola-Baranyi and Guillet, by the extrapolation of the values of the interaction parameter χ, at high temperatures, ranging from 70°–90°, 90°–110° and 110°–130°C down to 25°C. The values of the solubility parameter obtained, depending on the temperature ranges employed, are 9.8, 9.9 and 10.1, respectively.     

自粘聚合物改性沥青防水卷材胶粘剂

在SBS改性沥青防水卷材表面涂敷一层自粘性胶粘剂并以隔离纸覆盖，使用时撕掉隔离纸直接粘贴于屋面即可粘接密封牢，不但施工方便而且消除了熔融法施工造成的污染。该胶粘剂由沥青40％～65％，SBS 5％～30％，增粘剂2％～25％和助剂5％～25％构成。胶层具有可塑性、延展性，可自行填补屋面出现的裂缝，保证防水卷材的防水密封效果。     

广义线性模型与非线性模型参数的统计推断

概述了广义线性模型(含半参数广义线性模型)与非线性模型研究的新进展,着重讨论了它们参数估计的统计推断。近年来,广义线性模型与非线性模型的研究发展迅速,有着广泛的应用前景。     

凹凸棒粘土用作高水速凝注浆悬浮剂

以凹凸棒粘土作为高水速凝固化充填材料的悬浮稳定剂，考察了不同制浆机械对凹凸棒粘土制浆率的影响。采用高剪切混合乳化机预制的1％凹凸棒粘土浆配制高水速凝固化充填材料甲、已料单浆可获得满意的悬浮稳定效果。其充填体结石抗压强度早期发展迅速，后期持续增长。采用此工艺，注浆料的材料成本仅增加2％。     

下河沉积型瓷石的工艺特性与开发应用的探讨

本文论述了新近在江西下河发现的沉积型瓷石的地质特点、矿石特征、精泥性能、成瓷工艺及其开发应用前景。     

对甲醇精馏几个问题的认识

简述甲醇精馏三塔流程原理 ,分析了加压精馏塔及常压精馏塔物料和热量平衡关系 ,提出了操作中应注意的事项