不同活化剂对石油焦基活性炭孔结构的影响

以石油焦为原料 ,Na OH,KOH和 Na2 CO3 为活化剂制备活性炭 ,采用氮气吸附考察了不同活化剂对活性炭的比表面积、中孔和微孔孔径分布、孔容积及平均孔径等孔结构的影响 .结果表明 :KOH活化制备的活性炭包含 1 nm的微孔和 4nm的中孔 ,总孔容 0 .648cm3 /g,比表面积大 ;Na OH制备的活性炭以 1 nm的微孔为主 ,占总孔容 ( 0 .1 65 cm3 /g)的 98% ,平均孔径 1 .83nm;Na2 CO3 制备的活性炭以 4nm的中孔为主 ,占总孔容 ( 0 .1 43cm3 /g)的 68.5 % ,平均孔径 3.42 nm,比表面积小 .3种样品的孔径都呈现出多峰分布特征 .KOH和 Na2 CO3 活化制备的活性炭的 N2 吸附脱附曲线属于 型 ,Na OH活化制备的活性炭吸附脱附曲线属于 型 .     

气相法二氧化硅应用机理及特性

主要介绍了气相法二氧化硅在液态体系、干燥体系、固态体系中的作用机理；气相法二氧化硅在应用中的特殊性能；以及比表面积、pH、含水量、添加量、表面处理程度等气相法二氧化硅各项物理性能对应用性能的影响。     

Silicon Nitride Derived from an Organometallic Polymeric Precursor: Preparation and Characterization

Partially crystalline Si₃N₄, with nanosized crystals and a specific surface area greater than 200 m²/g, is obtained by pyrolysis of a commercially available vinylic polysilane in a stream of anhydrous NH₃ to 1000°C. This polymer does not contain N initially. Crystallization to high-purity α-Si₃N₄ proceeds with additional heating above 1400°C under N₂. The changes in crystallinity, powder morphology, infrared spectra, and elemental compositions, for samples annealed from 1000° to 1600°C under N₂, are consistent with an amorphous-to-crystalline transformation. Although macroscopic consolidation and local densification occur at 1400°C, volatilization and accompanying weight loss limit bulk densification. The effect of temperature on specific surface area is examined and related to the sintering process. These results are applicable to pyrolysis, decomposition, and crystallization studies of ceramics synthesized by polymeric precursor routes.     

An improved light attenuation technique for measuring large interfacial areas

A laser-based light attenuation technique was successfully used to measure interfacial areas as high as 5832 m²/m³ and Sauter mean bubble diameter varying between 50 and 5600 μm. Good agreement between this approach and the photographic technique was obtained particularly at low gas holdups.     

Surface Areas of Nitrated Hydrotalcites

Hydrotalcites in the nitrate form were prepared using microwave irradiation in the hydrotreatment step. The surface area (BET) of nitrated hydrotalcites was evaluated. Solids were characterized by atomic absorption, X-ray diffraction and BET analysis. Thermal pretreatment temperature determined the surface area of the hydrotalcites.     

Influence of Carbon on SOx Emissions from Glass Processing

Carbon reacts with Na₂SO₄ in glass batches, influencing SO _x emissions. To study the role of carbon active surface area (ASA) in the decomposition phenomena, Na₂SO₄ is reacted with three carbons with a wide ASA range. The decomposition behavior was evaluated by thermogravimetric analysis (TGA) and evolved gas analysis via mass spectrometry and Fourier transform infrared spectrometry. Higher carbon ASA yields lower decomposition temperatures. SO _x emissions are realized at temperatures as low as 773 K. Isothermal Na₂SO₄–C decomposition initiates via the nucleation of Na₂S. The rate constants for the nucleation regime are normalized against ASA, yielding an activation energy of 275 kJ/mol for nucleation.     

大面积水域浓度场测试方法及系统研究

针对大面积水域浓度场难以实现实时测量、测量精度不高等问题,采用了一种多通道荧光测试系统和方法。首先,基于单色光诱导荧光检测浓度(LIF)原理,使用探头获取离散点的浓度参数。然后,经总线或通信网络技术,将数百个测点连接起来。最后,通过数据总线或网络将采集的数据输送到中央测控计算机中,处理离散的数据后形成完整的浓度场。在恒定流浓度场中的试验结果表明,污染物测量相对误差均值不超过5%,单次测量相对误差最高值为8.33%,传感器线性度不超过5%,可检测的荧光素钠溶液浓度分辨率为0.001 ppm,系统测量稳定、精度较高。相较于其他浓度测量方法,该系统具有测量面积大、实时测量的优势,可为水污染防治等领域提供可靠的技术支撑。     

Experimental Investigation of Epoxy Bonded Polymethylmethacrylate Joints

This paper presents an experimental investigation into various aspects of epoxy-bonded polymethylmethacrylate (PMMA) and PMMA-to-aluminium joints. The effects of adhesive thickness, overlap area, surface roughness, and environmental exposure on the joint strength were studied. Results indicated that the joint strength was not directly proportional to the overlap area, while sanding had a positive effect on the joint strength. A negative effect was observed when adhesive thickness was increased. The fatigue behaviour of adhesively-bonded joints under dynamic loading was found to be independent of frequency, for the range of values tested; however, it was dependent on the test temperature with greater reduction in fatigue life observed in PMMA-to-aluminium joints at higher temperature. Empirical equations from which the fatigue life of joints can be predicted were obtained by regression analysis. Intermittent fatigue testing of the joints was also performed. The epoxy adhesive tested proved to be a satisfactory choice for outdoor exposure. The rate of degradation of the adhesive was slow with the adherend itself degrading at a faster rate than the adhesive or the bondline.     

Testing usability and trainability of indirect touch interaction: perspective for the next generation of air traffic control systems

This study aims to determine whether indirect touch device can be used to interact with graphical objects displayed on another screen in an air traffic control (ATC) context. The introduction of such a device likely requires an adaptation of the sensory-motor system. The operator has to simultaneously perform movements on the horizontal plane while assessing them on the vertical plane. Thirty-six right-handed participants performed movement training with either constant or variable practice and with or without visual feedback of the displacement of their actions. Participants then performed a test phase without visual feedback. Performance improved in both practice conditions, but accuracy was higher with visual feedback. During the test phase, movement time was longer for those who had practiced with feedback, suggesting an element of dependency. However, this ‘cost’ of feedback did not extend to movement accuracy. Finally, participants who had received variable training performed better in the test phase, but accuracy was still unsatisfactory. We conclude that continuous visual feedback on the stylus position is necessary if tablets are to be introduced in ATC.     

Greedy-search-based multi-objective genetic algorithm for emergency logistics scheduling

To enable the immediate and efficient dispatch of relief to victims of disaster, this study proposes a greedy-search-based, multi-objective, genetic algorithm capable of regulating the distribution of available resources and automatically generating a variety of feasible emergency logistics schedules for decision-makers. The proposed algorithm dynamically adjusts distribution schedules from various supply points according to the requirements at demand points in order to minimize unsatisfied demand for resources, time to delivery, and transportation costs. The proposed algorithm was applied to the case of the Chi–Chi earthquake in Taiwan to verify its performance. Simulation results demonstrate that under conditions of a limited/unlimited number of available vehicles, the proposed algorithm outperforms the MOGA and standard greedy algorithm in ‘time to delivery’ by an average of 63.57% and 46.15%, respectively, based on 10,000 iterations.