中厚板汽雾冷却技术的开发及应用

为解决济钢中板厂冷床能力不足问题，对汽雾冷却系统的技术原理、系统组成进行了研究及实际应用；应用汽雾冷却系统后，在保持钢板组织和力学性能不受影响的前提下，提高了钢板的降温速度，加快了生产节奏；经汽雾冷却的钢板，表面氧化层减薄1／2。     

ATM突发性业务阻塞控制

在ＡＴＭ网里业务阻塞控制是一个十分重要的问题，本文对一种缓冲漏桶业务阻塞控制算法在突发性业务输入情况下的性能进行了计算机模拟分析，模拟结构表明缓冲漏桶算法是一种适合于突发性业务的阻塞控制算法，文章在模拟结果的基础上给出了缓冲漏桶算法中参量选择的算法。     

高功率板条固体激光器研究的进展

本文对高功率板条固体激光器研究的进展和应用前景作了综合评述。结合作者部分工作,对板条激光器的热效应、聚光器和光学谐振腔等关键问题和技术进行了物理分析。     

A load dispatch method using fractional programming and semidefinite programming

This paper describes a load dispatch method which minimizes power cost—[fuel cost]/[electric output]—for a power system with thermal plants and energy storage facilities. The proposed method employs fractional programming to convert a minimization problem with fractional objective function to a series of quadratic minimization problems, and semidefinite programming to solve converted problems. The method provides the optimum time‐dependent power output/input and storage level of energy storage facilities as well as time‐dependent power output of thermal plants. The method has been applied to a power system with five thermal plants, two energy storage facilities of various performances, and five load demands. The optimum load scheme of four time mesh points is obtained for the thermal plants and energy storage facilities. The fractional programming successfully converges the optimal scheme through a few iterations. The semidefinite programming deals with a variable matrix of 164 dimensions, and 185 inequality constraints. © 2001 Scripta Technica, Electr Eng Jpn, 138(2): 49–58, 2002     

关于CEA混凝土膨胀剂的若干技术问题--与游宝坤同志讨论

作者阐述了CEA膨胀剂混凝土的膨胀量较大，干缩小，抗裂性能良好的特性，CEA与粉煤灰掺用提高强度，改善界面过渡层的性质，提高耐久性；CEA混凝土无Ca（OH）2溶出问题。文中列出GBJ119应用技术规范，说明CEA可用于防水工程。     

Electroclinic measurement of the coefficients of Landau expansion of some ferroelectric liquid crystals

The electroclinic effect in the smectic A phase of ferroelectric liquid crystals is a sensitive probe for measuring the soft mode response near the A-C* transition point. It is possible to evaluate several coefficients of the Landau theory describing the A-C* transition by simultaneously measuring the frequency dependence of both the optical signal and the current through the sample. We have made such measurements on a couple of homologous series [2S,3S]-4′-(2-chloro-3-methyl pentanoyloxy) phenyl-trans-4″-n alkoxy cinnamates synthesized in our labortory. The results show that the Landau meanfield theory is adequate to describe the A-C* phase transition in these compounds. Presented at the 15th International Liquid Crystal Conference, Budapest, 3–8 July 1994.     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.     

压力对Fe－29wt％Ni合金超细微粒特性的影响

利用蒸发冷凝法，制备了不同平均粒径的Ｆｅ－２９ｗｔ％Ｎｉ合金超细微粒。在不同压强下，将超细微粒压制成片。随压强增大，马氏体体积分数和比饱和磁化强度σｓ明显增大，而矫顽力Ｈｃ呈线性下降。压力效应与平均粒径ｄ大小密切相关     

转向柱管承载能力的试验研究

在分析转向柱管花键部位应力集中情况的基础上,通过对某厂生产的转向柱管扭转破坏的试验研究,得到如下结论:①转向柱管的承载能力与其外花键齿与方向盘中心内花键齿之间的非接触区长度有关,以花键端部过渡圆弧的直径大小为宜;②安装方向盘总成时所施加在安装螺母上的拧紧力矩在70N.m左右时,转向柱管的承载能力最大。