Experimental study on the heat transfer and flow characteristics of nanorefrigerants inside a corrugated tube

The heat transfer and flow characteristics of MWCNT-R141b nanorefrigerant with different mass fractions have been studied through experiments. Experimental results were compared with existing correlations. A two-step method was used to prepare the nanorefrigerants. Span-80 was used as surfactant with an average particle diameter of 20 nm. Transmittance method was used to evaluate the stability of nanorefrigerants. Results showed that the stability of MWCNT-R141b nanorefrigerant, which is the added dispersant, was good during the experiments. The 0.3 wt% MWCNT-R141b nanorefrigerants had optimal heat transfer enhancement effects compared with pure refrigerants. The maximum Nusselt number increased by 40%. The specific pressure drop of nanorefrigerant increased as the Reynolds number (Re) increased, and the specific pressure drop of the pure refrigerant was minimum, which is similar to R141b.     

Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

Characteristics of tiger nut milk: effects of milling

A standard method for the extraction of tiger nut milk has been introduced. It has been shown that, although milling duration improves the yield of tiger nut milk solids and its nutrient composition, there is a quantifiable loss of nutrient in the pressing residue during milk extraction. Milling duration improved the colloidal stability of the milk against creaming during 16 h of storage. A higher milling intensity resulted in the aggregation of biological polymers which resulted in colloidal destabilisation. Milling improved the lightness and stability and reduced browning rate of the tiger nut milk during storage. This report is important for the production of tiger nut milk of consistent and comparable characteristics. Milling has been introduced as a processing method for the qualitative and quantitative modulation of the properties of tiger nut milk. It is recommended to develop further strategies to improve the colloidal stability of tiger nut milk as a beverage.     

A Student's t-based density peaks clustering with superpixel segmentation (tDPCSS) method for image color clustering

Image color clustering is a basic technique in image processing and computer vision, which is often applied in image segmentation, color transfer, contrast enhancement, object detection, skin color capture, and so forth. Various clustering algorithms have been employed for image color clustering in recent years. However, most of the algorithms require a large amount of memory or a predetermined number of clusters. In addition, some of the existing algorithms are sensitive to the parameter configurations. In order to tackle the above problems, we propose an image color clustering method named Student's t-based density peaks clustering with superpixel segmentation (tDPCSS), which can automatically obtain clustering results, without requiring a large amount of memory, and is not dependent on the parameters of the algorithm or the number of clusters. In tDPCSS, superpixels are obtained based on automatic and constrained simple non-iterative clustering, to automatically decrease the image data volume. A Student's t kernel function and a cluster center selection method are adopted to eliminate the dependence of the density peak clustering on parameters and the number of clusters, respectively. The experiments undertaken in this study confirmed that the proposed approach outperforms k-means, fuzzy c-means, mean-shift clustering, and density peak clustering with superpixel segmentation in the accuracy of the cluster centers and the validity of the clustering results.     

基于分形插值的改进趋势面拟合法在地面沉降中的应用

针对区域地面沉降监测点数量有限、分布不均的情况,一般采用空间插值的手段建立表面拟合模型来解决。基于分形插值,采用随机选择迭代函数的思想对传统的趋势面拟合法作出改进,改进后拟合优度系数提高0.03,达到0.995,且改进前后的拟合结果符合显著性检验的要求。实验结果表明:改进前后趋势面拟合法拟合结果满足地面沉降监测的精度要求,改进后方法的拟合优度更高,对现实地面沉降量变化的描绘更加真实,可为沉降灾害评价工作提供更准确的依据。     

Iterative equalization combining algorithm in intersymbol interference channel

To realize joint optimization of spatial diversity and equalization combining in the intersymbol interference (ISI) channel, an iterative equalization combining algorithm is proposed. The proposed algorithm uses the coefficients of Turbo equalization to calculate the combination weights without estimating the signal to noise ratio in each diversity branch. The equalized symbols from different diversity branches are combined, and the extrinsic information output from the decoder is fed back to the equalizers, so as to exchange soft information between the equalizers and the decoder. The performance of the proposed algorithm is analyzed using the extrinsic information transfer (EXIT) chart and verified by simulations. Results show that our approach fully exploits time domain information from the multipath channel and spatial domain information from multi receiving antennas, which efficiently improve the performance of the receiver in the severe ISI channel.     

不同折流板结构螺旋折流板换热器传热性能的比较(英文)

Numerical simulations were performed on flow and heat transfer performances of heat exchangers having six helical baffles of different baffle shapes and assembly configurations, i.e., two trisection baffle schemes, two quadrant baffle schemes, and two continuous helical baffle schemes. The temperature contour or the pressure contour and velocity contour plots with superimposed velocity vectors on meridian, transverse and unfolded concentric hexagonal slices are presented to obtain a full angular view. For the six helix baffled heat exchangers, the different patterns of the single vortex secondary flow and the shortcut leakage flow were depicted as wel as the heat transfer properties were compared. The results show that the optimum scheme among the six configurations is a circumferential overlap trisection helix baffled heat exchanger with a baffle incline angle of 20° (20°TCO) scheme with an anti-shortcut baffle structure, which exhibits the second highest pressure dropΔpo, the highest overal heat transfer coefficient K, shel-side heat transfer coefficient ho and shel-side average comprehensive index ho/Δpo.     

Distributed wireless power transfer in sensor networks with multiple Mobile Chargers

We investigate the problem of efficient wireless power transfer in wireless sensor networks. In our approach, special mobile entities (called the Mobile Chargers) traverse the network and wirelessly replenish the energy of sensor nodes. In contrast to most current approaches, we envision methods that are distributed and use limited network information. We propose four new protocols for efficient charging, addressing key issues which we identify, most notably (i) what are good coordination procedures for the Mobile Chargers and (ii) what are good trajectories for the Mobile Chargers. Two of our protocols (DC, DCLK) perform distributed, limited network knowledge coordination and charging, while two others (CC, CCGK) perform centralized, global network knowledge coordination and charging. As detailed simulations demonstrate, one of our distributed protocols outperforms a known state of the art method, while its performance gets quite close to the performance of the powerful centralized global knowledge method.     

Correlation between motion of source bender element and feedback signal induced by self-monitoring

Since the introduction of bender element tests to soil testing, the reliability of the estimated travel time has been the most serious problem. The author has previously shown a potential solution whereby removing the response of the bender element subsystem from the whole response could dramatically improve the accuracy of the travel time estimation. In order to lay the foundation for estimating the response of the bender element subsystem, this paper examines the correlation between the displacements of the element and the induced feedback signals by employing a self-monitoring element. The response of the self-monitoring element is modeled as a transfer function involving two internal transfer functions that relate the input signals to the displacements and the displacements to the feedback signals, respectively. Using a laser displacement sensor, the displacements are directly measured through the entire surface and reveal the three-dimensional bending motion of the element oscillating in both longitudinal and width directions. The feedback signals are similar to, but inconsistent with, the tip displacements, and an attempt is made to correct the feedback signals. Finally, a conclusion is given on the potential for estimating the response of the bender element subsystem using the self-monitoring element.     

Stress distribution in thick-walled cylinder due to non-uniform radial pressure on the example of reinforcement corrosion in concrete

This paper presents an analytical solution to the non-uniform pressure on thick-walled cylinder. The formulation is based on the linear elasticity theory (plain strain) and stress function method. As an example, the proposed solution is used to model the stress distribution due to non-uniform steel reinforcement corrosion in concrete. The model is formulated considering different scenarios of corrosion pressure distribution. It is validated against the finite element model for different cases of non-uniform pressure distributions. The results show that the corrosion-induced cracks are likely to start just beyond the anodic zone. This is confirmed by the experimental tests on concrete cylinder exposed to non-uniform accelerated corrosion of steel reinforcement. The model can be effectively used to calculate the distribution of corrosion-induced stresses in concrete.