可控震源施工中电台数据传输不良的原因分析及排除

可控震源在施工中,常常出现各种电台干扰,导致震源数据传输不正常或震源收不到仪器发出的遥控启动信号,影响正常施工.本文介绍了各种电台干扰引起的故障现象,分析了故障产生的原因,给出了故障的排除方法.     

Cable Modem的原理与反向噪声的控制

介绍Cable Modem的基本概念、传输方式、标准规范，并对影响Cable Modem工作稳定性的反向噪声问题进行技术分析，并提出预防控制措施。     

一种基于m序列的图像随机加密与实时传输方案

提出了一种基于m序列的图像随机加密与实时传输方案。在加密时用m序列构造的相位函数取代了双相位输码方法中用作密钥的随机相位掩模，极大地压缩了密钥的数据量，使密钥的传送更加方便快捷。并在前有基础上加以改进，可以轻松地加密彩色图像。在完成加密后，可实时地在网络上传送加密图像，在接收端进行解密。最后进行了计算机模拟实验，实验结果表明该方案是可行的，并且易于实际应用。     

16×10.7 Gb/s 1 600 km普通单模光纤环路传输研究

利用双折射光纤环设计了可调功率均衡滤波器,实现了16路16×10.7 Gb/s NRZ码、超过1 600 km常规单模光纤(SMF)的系统传输及性能测试,信道误码率均小于3×10-5(FEC纠错前).数值仿真并实验研究了对单环长度240 km、损耗超过80 dB的环路16路10.7 Gb/s波分复用(WDM)系统传输的优化.传输7圈后,功率均衡器降低了信道功率不平坦度超过5 dBm.     

入射光的偏振和强度对分光镜透／反比的影响

采用能量流分析法推导了一束线偏振光经分光镜分光形成透射／反射光的能量表达式。分别讨论了入射光强度不变而偏振方向变化以及二者同时变化对分光镜透／反比的影响。通过旋转主光路中的偏振片来模拟入射光的偏振方向和强度变化，实验验证了分光比的变化规律。     

双室充氮包装机的技术改进

分析了原机型的性能特点和不足之处,介绍了改进方案。     

低差错平底特性的非规则LDPC码的设计

介绍了非规则LDPC码的发展并给出了其优势及缺点，重点论述用ACE算法来构造非规则LDPC码从而降低其差错平底特性。对降低非规则LDPC码的差错平底特性的其它方法提出了展望。     

Chemische Zusammensetzung und Mikrostruktur polymerabgeleiteter Gläser und Keramiken im System Si–C–O. Teil 2: Charakterisierung der Gefügeausbildung mittels hochauflösender Durchstrahlungselektronenmikroskopie und Feinbereichsbeugung

Chemical Composition and Microstructure of Polymer‐Derived Glasses and Ceramics in the Si–C–O System. Part 2: Characterization of microstructure formation by means of high‐resolution transmission electron microscopy and selected area diffraction Liquid or solid silicone resins represent the economically most interesting class of organic precursors for the pyrolytic production of glass and ceramics materials on silicon basis. As dense, dimensionally stable components can be cost‐effectively achieved by admixing reactive filler powders, chemical composition and microstructure development of the polymer‐derived residues must be exactly known during thermal decomposition. Thus, in the present work, glasses and ceramics produced by pyrolysis of the model precursor polymethylsiloxane at temperatures from 525 to 1550 °C are investigated. In part 1, by means of analytical electron microscopy, the bonding state of silicon was determined on a nanometre scale and the phase separation of the metastable Si–C–O matrix into SiO₂, C and SiC was proved. The in‐situ crystallization could be considerably accelerated by adding fine‐grained powder of inert fillers, such as Al₂O₃ or SiC, which permits effective process control. In part 2, the microstructure is characterized by high‐resolution transmission electron microscopy and selected area diffraction. Turbostratic carbon and cubic β‐SiC precipitate as crystallization products. Theses phases are embedded in an amorphous matrix. Inert fillers reduce the crystallization temperature by several hundred °C. In this case, the polymer‐derived Si–C–O material acts as a binding agent between the powder particles. Reaction layer formation does not occur. On the investigated pyrolysis conditions, no crystallization of SiO₂ was observed.     

Sociotechnical systems, risk management, and public health: comparing the North Battleford and Walkerton outbreaks

Accidents in different complex sociotechnical systems are rarely compared using the same theoretical framework for risk management. We conducted a comparative analysis of two Canadian public health disasters involving drinking water distribution systems, the North Battleford Cryptosporidium parvum outbreak in April 2001 and the Walkerton E. coli outbreak in May 2000. Both accidents resulted from a complex interaction between all levels of a complex sociotechnical system. However, the low-level physical and individual factors differed in the two cases, whereas, the high-level governmental and regulatory factors tended to be the same. These findings may have implications for the design of public policies to minimize risk in complex sociotechnical systems.     

应用AR模型的IMU误差系数漂移预测研究

将影响IMU误差系数漂移并难于分离的多种因素综合为一种因素，假定IMU误差系数的漂移由一特定系统所引起，从而采用时间序列建模方法进行IMU误差系数漂移的预测。该方法具有消除各因素具体分析中的不确定性并减少其工作员的优点。文中描述了其原理，对某惯组的33个误差系数进行了时间序列建模与预测并得到有效的结果。最后还阐述了存在的问题及其解决方法。