用边界元法提取VLSI版图电阻

介绍了ＶＬＳＩ版图验证中电阻提取的基本原理和主要方法，给出了一种新颖的基于边界元法的电阻提取算法。该算法采用变节点单元，较好地解决了实际问题中经常出现的角点问题。通过应用该算法对几个实例进行提取，证明使用本文的算法不仅在精度上而且在占用ＣＰＵ时间上都取得了令人满意的效果     

强激光的时间整形和空间整形——利用双折射透镜组实现激光束的空间整形

本文使用琼斯矩阵方法对双折射透镜组空间整形系统的光强透射率分布和工作特性进行了分析,并讨论了工程设计中参数的选择以及加工误差带来的影响等有关问题.     

The principle and fundamental characteristics of brushless three-phase synchronous induction motor with two stators

Brushless three-phase synchronous motor involving a rotating ac exciter on the same shaft as the motor and with the windings linked through a shaft-mounted rectifier is widely used as medium and large capacity machines. However, the motor needs to fit with damping windings for self-starting outside of the field winding in the rotor and needs to equip discharge resistance with complex electronic device to dispose of electromagnetic force induced in the field winding at starting. Therefore, the rotor structure is very complex, and there are disadvantages, especially for the robust and highly reliable motor that is desired. To solve the problem found in traditional motors, the authors proposed a brushless three-phase synchronous induction motor with two stators and one wound rotor. This problem is solved because the proposed motor is of two-stators structure: the rotor winding operates as a secondary winding of induction motor at starting and as the field winding at synchronous operation. The motor can self-start as a wound-rotor induction motor without external secondary resistance. Therefore, discharge resistance is not necessary; the starting equipment is very simple and the rotor structure is robust. It is possible to start with high torque. In this paper, the basic constitution of the proposed motor and the principles of operation are described in detail. The experimental results at starting and pulling into synchronism are shown for confirming the principles of operation and the experimental and numerical results of the starting characteristics. The load ones and the generating ones are shown and then the practical use of the proposed motor is confirmed.     

WTG420铁路罐车用钢的组织结构和力学性能分析

分析了ＷＴＧ４２０铁路罐车用钢的组织结构和力学性能。提出了冶炼与轧制的技术关键，其一，添加稀土元素改善钢中夹杂物；其二，采用控轧控冷使铁素体晶粒细化。     

核孔膜生产线膜微孔制备工艺实验研究

本文介绍核孔膜生产线,重点描述了膜微孔制备工艺的实验研究。对于PC和PES膜,已得到32种工况下的扩孔公式,其形式为D=A+Bt,其中D——孔径,t——扩孔时间,A,B为特定工艺参数下的常数值.通过实验。得到了膜孔密度N与300~#核反应堆功率P、热柱辐照位置L的经验公式,即N=6.97×10~5×10~3×101~(1.18L).在本生产线上可生产最大幅面为3 140mm×240mm,孔径为0.04～10 μm的多系列多规格的核孔膜产品。     

冷轧厂酸洗机组3号横剪大流量中高压液压系统设计方案探讨

在宝钢２０３０ｍｍ冷轧厂酸洗机组中，为了满足厚规格ＩＦ钢的生产，拟将原有的气动式剪切机改成液压式剪切机。为此，设计了一套中高压大流量的液压系统以满足３号横剪大剪切力（最高达７００ｋＮ）和快速剪切（３秒／次）的需要。由于采用了蓄能器增速回路和二通插装阀控制技术，使该液压系统较传统的剪切机液压系统具有响应速度快、体积小、重量轻、发热少和降低电机能耗等优点。     

Fundamental solutions for half plane with an oblique edge crack

An elastic half plane with an oblique edge crack is considered in this paper. A pair of concentrated forces or point dislocations is assumed to act at an arbitrary point in the half plane. The half plane with an edge crack is first mapped into a unit circle by a rational mapping function so that the following analysis can be carried out on the mapped plane analytically. Then the complex stress functions are derived by separating the whole problem into two parts; one is the principal part corresponding to the infinite plane acted on by concentrated forces or dislocations, the other is the holomorphic part, which can be determined by making use of the property of regularity of complex stress functions. The stress intensity factors of the crack can be calculated with different inclined angles of the crack, and the displacement and stress components at an arbitrary position in the half plane can be expressed explicitly.     

传输线衰减常数与柱形谐振器Q值的关系

文中严格地讨论了任意截面形状，任意模式的柱形谐振腔Ｑ值与构成该谐振器的传输线衰减常数间的关系，给出了更一般的公式，推广了Ｄａｖｉｄｓｏｎ和Ｓｉｍ－ｍｏｎｄｓ＾［１］、Ｂａｒｌｏｗ和Ｃｕｌｌｅｎ＾［２］以及Ｙｅｈ和Ｓｈｉｍａｂｕｋｕｒｏ＾［３，４］的结果。     

液压胀形轧辊油槽深度的确定

对液压胀形轧辊（即国外的ＶＣ轧辊）辊套热装后的弹性变形进行了有限元分析，给出了确定油槽最小深度的计算公式。本文的有限元计算结果与实验结果吻合，某些结论可为液压胀形轧辊的结构设计提供理论依据。     

用于X光激光实验的反射式线聚焦光学系统的设计和分析

基于三维光线追迹的象差计算,对卢瑟福实验室用离轴球面反射线聚焦系统作了分析。然后,首次提出了用于X光激光实验的两类新的反射式线聚焦构型,即反射式光楔列阵和光锥列阵系统,并作了计算。最后,对所得结果作了比较和讨论。