方柱体镦粗的两个新力学模型

在对平板间镦粗圆柱体的研究［１，２，３］基础上，进一步对普通平板间的方柱体镦粗，进行了工程力学的分析，提出了二个新力学模型，并进行了实验验证。这为形成新的拔长理论［４，６］奠定了力学基础。     

基于电网电力设备“两态”管理体制的安全生产责任体系建设的研究与应用

介绍了安全生产责任体系建设的基本内容,分析了电网电力设备安全生产现状及存在问题,并结合相关实践经验,分别从强化电网电力设备状态检修等多个角度与方面,探讨了电网电力设备安全生产责任体系建设策略。     

Drawing of square twisted wire

The shape of the deformation zone during drawing of square twisted wires is described in this paper. The condition of the stable deformation of the wire is formulated. This condition is satisfied by the constant value of the pitch of the helical surface of the die. The work focuses on the investigation of the influence of the die cone angle on the drawing parameters, in particular on the drawing stress.     

1 250 mm五机架六辊冷连轧工艺控制系统核心技术

简要介绍了自主设计制造、具有完全自主知识产权的1 250 mm五机架六辊冷连轧产线工艺及设备特点。重点阐述了冷连轧工艺控制系统的硬件配置、软件架构及核心技术。采用基于简易有限元的轧制力模型及基于成本函数的多目标负荷分配模型，实现了高精度的轧制规程计算。开发了原料板快速启车技术与板形多变量综合最优控制技术，实现了冷轧产品的尺寸精准控制。现场实际应用效果表明，机组稳定运行率达到99.8%以上，不同规格的产品厚度控制精度均达到±0.8%以内，板形控制精度均达到5I以内。     

用WKB方法讨论透射系数和反射系数

本文用WKB近似方法讨论了势垒贯穿问题系数T和其透射反射系数R之和恒等为1,即满足恒等式T R=1,并进一步得出这一结论不仅适用于一般势垒贯穿而且在方势垒贯穿中也成立,最后讨论了势垒贯穿的几种极限情况,例如,h→0(即经典情况),势垒高度v→∞、v→0,势垒宽度a→∞、a→0,等几种特殊情况下的T及R的取值问题。     

Adaptive model predictive inventory controller for multiproduct warehouse system

An inventory control system has been developed for a distribution system consisting of a single multiproduct warehouse serving a set of customers and purchasing products from multiple vendors. Purchase orders requesting multiple products are delivered to the warehouse in a process referred to as joint replenishment. The receipt of customer orders by the warehouse proceeds in order intervals and in order quantities that are subject to random fluctuations. The objective of warehouse operation is to minimize the total cost while maintaining inventory levels within the warehouse capacity by adjusting the purchase order intervals and quantities. An adaptive model predictive control algorithm is developed using a periodic square wave model to represent the material flows. The adaptive concept incorporates a stabilized minimum variance control-type input calculation coupled with input/output stream parameter predictions. The boundedness of the control output under the suggested algorithm is mathematically proven under the assumption that disturbances in the orders are bounded. The effectiveness of the scheme was demonstrated using simulations.     

聚氯乙烯塑料中多种邻苯二甲酸酯类增塑剂的同时测定

为了在线监控聚氯乙烯塑料中增塑剂的含量,利用傅立叶变换红外光谱法-ATR技术测定样品的红外光谱,采用偏最小二乘法对所测红外光谱进行分析,建立了一种无损快速分析方法,定量地测定聚氯乙烯塑料中多种邻苯二甲酸酯类增塑剂的含量。该方法测量精密度的变异系数小于6%,测量准确度的变异系数小于3%。该方法不受基体的干扰,简单快速,适合于流水线的质量控制。     

Pressure drop for single and two‐phase flow of non‐newtonian liquids in helical coils

New experimental results on pressure loss for the single and two‐phase gas‐liquid flow with non‐Newtonian liquids in helical coils are reported. For a constant value of the curvature ratio, the value of the helix angle of the coils is varied from 2.56° to 9.37°. For single phase flow, the effect of helix angle on pressure loss is found to be negligible in laminar flow regime but pressure loss increases with the increasing value of helix angle in turbulent flow conditions. On the other hand, for the two‐phase flow, the well‐known Lockhart‐Martinelli method correlates the present results for all values of helix angle (2.56‐9.37°) satisfactorily under turbulent/laminar and turbulent/turbulent conditions over the following ranges of variables as: 0.57 ≤ n′ ≤ 1; Re′ < 4000; Re_l < 4000; Re_g < 8000; 8 ≤ x ≤ 1000 and 0.2 ≤ De′ ≤ 1000.     

城市污水处理厂污泥中温两相厌氧消化的研究

采用中温两相厌氧消化处理西安市污水处理厂污泥,结果表明,污泥可在较短的停留时间(296 h,产酸相30 h,产甲烷相266 h),较高的有机负荷(约2.65 kg VS/m3.d)下稳定运行,系统VS去除率38.87%,pH≈7.5,产气速率6.33 L/L.d,单位VS产气率3.00 L/g。与单相厌氧消化处理结果对比,两相厌氧消化系统的停留时间可减少一半,而污泥有机负荷提高2倍,且有机物的去除率大,处理效果好,稳定性高,抗冲击负荷能力强,产气性良好。