城市污水处理厂污泥中温两相厌氧消化的研究

采用中温两相厌氧消化处理西安市污水处理厂污泥,结果表明,污泥可在较短的停留时间(296 h,产酸相30 h,产甲烷相266 h),较高的有机负荷(约2.65 kg VS/m3.d)下稳定运行,系统VS去除率38.87%,pH≈7.5,产气速率6.33 L/L.d,单位VS产气率3.00 L/g。与单相厌氧消化处理结果对比,两相厌氧消化系统的停留时间可减少一半,而污泥有机负荷提高2倍,且有机物的去除率大,处理效果好,稳定性高,抗冲击负荷能力强,产气性良好。     

应用电导探针测定固－液两相流的局部速度

研制了用于测定固－液两相流液相局部速度的双电极电导探针，并在０．７５ｍ×０．７５ｍ×１ｍ方形固－液搅拌槽内测定了叶轮排出流区的速度分布。     

Energy Efficiency of Two‐Phase Mixing in a Modified Bubble Column

Energy efficiency for gas liquid mixing in a modified downflow bubble column reactor has been analyzed in this paper. Efficiencies of the different parts of the bubble column have been assessed on the basis of energy dissipation. Prediction of the energy dissipation coefficient as well as energy utilization efficiency due to gas‐liquid mixing as a function of different physical, geometric and dynamic variables of the system has been done by correlation method. The distribution of energy utilization in the different zones of the column has also been analyzed. Experiments were carried out with air‐water and air‐aqueous solutions of carboxy methyl cellulose with different concentrations.     

静态混合器气液两相流压降的数值模拟及实验研究

气泡流经过静态混合器的压降问题涉及到舰船动力系统性能的好坏。在分析了气泡平均驰豫时间的基础上,结合k ε湍流模型,利用平衡流模型模拟静态混合器内形成的稀疏湍流气泡流,得到了混合器内两相流流场。空气—水系统的压力降实验表明,计算流体力学模拟能够很好地预测SMV型静态混合器内气泡流的压降,是静态混合器设计的有效手段。     

六偏磷酸钠的生产工艺

本文对六偏磷酸钠的性质、用途及生产工艺进行论述并介绍从日本引进１．５ｋｔ／ａ食品级六偏磷酸钠生产装置投产运行情况。     

颗粒多孔表面强化沸腾传热动力学研究

通过对颗粒多孔层几何结构、沸腾两相流及传热的理论分析，提出了微型通道薄膜环状蒸发物理模型和沸腾传热机理，建立了颗粒多孔表面强化沸腾传热动力学模型。该动力学模型与实验数据吻合良好，可用于工程设计。     

Advancements in the design and validation of an air pollution integrated assessment model for Spain

This paper describes the design and application of the Atmospheric Evaluation and Research Integrated model for Spain (AERIS). Currently, AERIS can provide concentration profiles of NO₂, O₃, SO₂, NH₃, PM, as a response to emission variations of relevant sectors in Spain. Results are calculated using transfer matrices based on an air quality modelling system (AQMS) composed by the WRF (meteorology), SMOKE (emissions) and CMAQ (atmospheric-chemical processes) models. The AERIS outputs were statistically tested against the conventional AQMS and observations, revealing a good agreement in both cases. At the moment, integrated assessment in AERIS focuses only on the link between emissions and concentrations. The quantification of deposition, impacts (health, ecosystems) and costs will be introduced in the future. In conclusion, the main asset of AERIS is its accuracy in predicting air quality outcomes for different scenarios through a simple yet robust modelling framework, avoiding complex programming and long computing times.     

Effect of thiophosphoryl compounds as accelerators and coupling agents on the vulcanization of NR‐XNBR blend

The effect of a number of thiophosphoryl compounds [viz., bis(isobutyl) thiophosphoryl di‐, tri‐, and tetrasulfides and bis(dicyclohexyl) thiophopsphoryl di‐, tri‐, and tetrasulfides] on natural rubber (NR)‐carboxylated nitrile rubber (XNBR) blend was studied. All these thiophosphoryl compounds are capable of forming interrubber links leading to covulcanized blends which exhibit a fair degree of synergism with respect to physical properties, the maximum being obtained at the 25% NR and 75% XNBR blend composition. This is an obvious claim that the blend under investigation is technologically compatible, having some degree of interrubber interaction which is enhanced in case of two‐stage vulcanization. The existence of interrubber interaction is judged by the swelling experiment. The blend morphology assessed by SEM micrographs corroborates the foregoing observations and accounts for the significant improvement in physical properties of the blend vulcanizates, particularly in two‐stage vulcanization. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3286‐3299, 2002     

浅谈皮带定量给料机的机械配置选型

皮带定量给料机是目前水泥生产企业中最为常见的过程计量和配料的设备。作者结合多年来开发、调试和使用皮带定量给料机的实践经验与资料积累，介绍了如何根据实际需要和使用量程，通过对皮带定量给料机的主要机械参数的计算来合理地选用定量给料机的型号和规格。     

优化甲醇工艺操作 提高产品质量

本文介绍了甲醇三塔精馏的产品质量控制及其影响因素 ,并提出了常压塔负压的处理方法。