文东油田连续气举优化配气数学模型建立及应用

针对连续气举在开发过程中出现的注入气利用效率低、综合效益差的问题，建立了供气能力有限时的优化配气数学模型，给出了解析法求解过程。文东油田现场试验表明，应用该技术可以实现连续气举井的合理配气，并提高油井产量，适合在油田推广应用。     

浅谈电梯选型应注意的问题

电梯选型配置问题是个十分有实际意义的话题。本文结合作者多年来检测检验电梯的经验，浅谈几点选型配置应注意的问题。     

Functional and sensory properties of chicken meat from spent-hen carcasses deboned manually or mechanically in Jordan

Samples of chicken meat from spent laying hens were obtained by four different methods: (1) manual deboning of whole carcasses; (2) manual deboning of skinned carcasses; (3) mechanical deboning of whole carcasses; and (4) mechanical deboning of skinned carcasses. The meat was packaged, frozen and stored at ?18 °C for up to 3 months. Functional properties studied were pH, emulsifying capacity (EC) and water‐holding capacity (WHC) and, in addition, pigment concentration was investigated. Sensory properties included aroma, colour, texture and overall acceptability, as judged by a trained panel using a nine‐point hedonic scale. Removal of the skin prior to deboning by either method gave significantly higher values (P < 0.05) for EC, while WHC values were not significantly different among the experimental treatments, despite higher pH values for mechanically‐deboned meat, with and without skin. Pigment concentrations were highest in meat from Treatment 4 and lowest for Treatment 1, but values for both methods of deboning were affected by the presence of skin. There were no significant differences between treatments for any of the sensory properties studied. Changes occurring in the meat during frozen storage are described.     

丙烯酸接枝聚丙烯纤维的结构与性能

本文研究了用化学引发剂引发丙烯酸接枝聚丙烯纤维的某些影响因素。红外光谱分析表明，丙烯酸接枝在聚丙烯大分子链的叔碳原子上。Ｘ－射线衍射和ＤＳＣ分析指出，纤维接枝后结晶度有所增加，接枝前纤维存在的β－变体转化成了α－变体，接枝纤维的吸湿性、离子交换容量和染色性随接枝率增加而增大。接枝纤维的力学性能有所下降。     

武钢 3×10~4m~3/h 空分手动变负荷生产的探索与实践

对武钢引进的两台３×１０４ｍ３／ｈ空分设备，为改变其自动变负荷生产调节范围小、时间长的问题，采用了人工手动变负荷的操作方法。实践表明：扩大了增减产范围，缩短了调节时间，有十分明显的综合经济效益，可供大型空分变负荷生产借鉴参考。     

二滩电厂双缸液压启闭机原理及故障分析

二滩电厂表孔采用弧形门,启闭形式为双缸液压启闭机.自投入运行以来,运行状况良好.汛期启闭方式已由原来的现地手动操作过渡到远方控制自动启闭.在闸门起落的过程中,由于工况的不同,两缸会出现不同步现象,因此设计中考虑了纠偏回路.本文简单介绍了二滩电厂表孔液压启闭机的原理和故障情况.     

锚索测力计有关应用问题的探讨

通过分析锚索测力计因受力状态不同而带来的系统误差,提出了测力计实测锚固力的修正方法及部分测力计传感器失效后延续锚固力测值的计算方法.     

紧凑 Tokamak(球形环)聚变堆第一壁及中心导体柱上中子负荷及核热计算与分析

采用通用蒙特卡罗粒子输运程序ＭＣＮＰ／３８计算低环径比Ｔｏｋａｍａｋ（紧凑环或球形环）聚变堆第一壁及中心导体上的中子壁负荷分布和核热沉积分布，并与常规Ｔｏｋａｍａｋ堆第一壁上中子壁负荷分布和核热沉积分布进行比较、分析。结果表明，在中子壁负荷归一化为１ＭＷ／ｍ２时，与常规Ｔｏｋａｍａｋ相比，在低环径比Ｔｏｋａｍａｋ堆第一壁及中心柱表面上中子壁负荷分布峰值并不比常规Ｔｏｋａｍａｋ堆第一壁上的峰值高，而且低于低环径比Ｔｏｋａｍａｋ堆整个第一壁上的平均值，而中心柱上的核热沉积峰值稍高于常规Ｔｏｋａｍａｋ堆第一壁上的核热沉积峰值，但对较高中子壁负荷情况，中心导体柱上的核热沉积和辐照损伤仍可能是比较严重和值得特别研究的问题。     

Multiobjective dynamic load-dispatching method for optimal operation of power systems

A new practical method is proposed which gives a quasi-optimal solution of the dynamic load-dispatching problem formulated by a multiconstraint multiobjective optimization problem. Here, the multiple constraints are rate reserve constraints and power flow ones, and the multiple objectives are fuel cost and CO₂ emission. The proposed method is an integration of the following three techniques: (1) “Group Dispatch Scheme,” which is developed by the authors, is used to satisfy a violated constraint easily. This scheme consists of three steps. The first step is to classify all generators into two groups. One is the group which should be more loaded to satisfy the violated constraint, and the other is the should-be less loaded group. The second step is to add some load to the former group, and to subtract the same load from the latter. The third step is to dispatch each group load to each groups generators, respectively; (2) the dynamic load-dispatching algorithm is used which provides, in practical time, quasi-optimal generation trajectories; (3) the conventional weighting parametric method is used to obtain a Pareto optimal solution of multiobjective problems. The effectiveness of the method is clarified by a computer simulation on the actual power system of Kansai Electric Power Company.     

Decisive arrival law parameters and a general finite capacity queueing problem

This paper addresses the problem of finding the parameters of the arrival law which most significantly influence expected occupation and loss of a finite capacity queue. The input process is supposed to be ergodic and wide sense stationary. We show that it is mostly possible to fit an MMPP(2) to the decisive parameters of observational data. Numerical examples illustrate the importance of the decisive parameters, called key parameters, and also show the accuracy of the proposed fitting procedure. Finally, in the appendix we present the solution of the finite capacity queueing problem with Special Semi Markov Process (SSMP) arrivals and a general service strategy.