有限体积法求解立体角离散误差

为解决采用有限体积法求解辐射传输方程时引起离散误差的问题,从有限体积法立体角内热流密度的求解过程出发,运用泰勒级数推导了近似误差的表达式,并分析影响离散误差的各种因素,包括离散射线数,辐射强度分布,假散射及网格比.根据分析结果,采用辐射强度的连续分布模型,模拟了各种因素对误差的影响.结果表明,辐射强度的分布函数对于有限体积法的离散误差有一定程度影响.当增加网格数及减小网格尺寸比时,可以有效地减小离散误差.假散射与离散误差间呈较强的非线性耦合关系.     

K8型单层球面网壳支座减震

为了对跨度为60 m的K8型单层球面网壳进行了减震分析,分别将结构的支座设置成弹性支座和弹性阻尼支座,对结构进行减震控制.结合对结构在有控和无控状态下自振特性的分析,阐述了单层球面网壳结构的减震控制原理.在常遇地震作用下,得到网壳结构的最大水平位移、减震支座的最大水平位移、最大支座反力和最大杆件内力.通过改变支座的刚度和阻尼系数,对两种减震方案的减震效果进行比较.研究结果表明:两种减震装置均有效地控制了K8型单层球面网壳结构的支座反力,弹性阻尼支座还可以明显地降低减震支座的水平位移.     

CJ91胶粘剂在螺旋振动光整机中的应用

螺旋振动光整机槽内壁的橡皮保护层由于老化及磨损等原因出现裂口甚至脱落现象，严重影响设备的使用寿命和闸把壳体的外观质量。通过分析和试验筛选出螺旋振动光整机的理想胶粘荆——CJ91胶粘剂并介绍了粘接修补工艺。     

基于解析解的四阶PDE曲面裁剪方法

该文提出了一种可以广泛应用于四阶PDE曲面的裁剪方法。利用PDE的参数域内的曲线在曲面上投影,得到所求裁剪曲面的边界曲线,然后通过边界曲线的导矢与曲面在边界曲线处的法向量得到边界曲线处的跨界导矢,最后以求得的裁剪曲面的边界曲线以及裁剪曲面在边界曲线处的跨界导矢为PDE曲面的边界条件,用四阶的PDE曲面方程求得PDE裁剪曲面。     

Self-excited vibration problems of maglev vehicle-bridge interaction system

The self-excited vibration problems of maglev vehicle-bridge interaction system were addressed, which greatly degrades the stability of the levitation control, decreases the ride comfort, and restricts the cost of the whole system. Firstly, the coupled model containing the quintessential parts was built, and the mechanism of self-excited vibration was explained in terms of energy transmission from levitation system to bridge. Then, the influences of the parameters of the widely used integral-type proportion and derivation（PD） controller and the delay of signals on the stability of the interaction system were analyzed. The result shows that the integral-type PD control is a nonoptimal approach to solve the self-excited vibration completely. Furthermore, the differential-type PD controller can guarantee the passivity of levitation system at full band. However, the differentiation of levitation gap should be filtered by a low-pass filter due to noise of gap differentiation. The analysis indicates that a well tuned low-pass filter can still keep the coupled system stable.     

20CrMnTi螺旋锥齿轮中出现圆鼓泡问题的分析

在对机车转向架螺旋锥齿轮的粗、精加工中发现其表面鼓起许多小泡，将其剖开酸洗后呈现为小裂纹状，该现象在实际生产中较为罕见，对此进行分析，探讨，查找原因，确定这是钢材内气泡未能焊合的结果，为此制定了改进措施。     

A global cutter positioning method for multi-axis machining of sculptured surfaces

Traditional cutter positioning methods have defects of global errors and incomplete optimization. Because of using local differential geometry and focusing on the cutting contact point, these defects cannot be avoided and will deteriorate accuracy in precision machining. The authors presented the conception of actual cutting edge of a toroidal mill which was extended from cutting contact point, and pointed out its importance in programming. Instantaneous cutter position error (ICPE) was also investigated. A new global method based on the ICPE curve was presented. Taking the relationship between surface and cutter into consideration thoroughly, this global method shows many advantages which have been verified by simulation and cutting tests.     

Thermal error measurement and modelling in machine tools.: Part I. Influence of varying operating conditions

Thermal error in machine tools has been observed to be closely linked to the temperature of critical elements of the machine. It was found, in the experiments conducted herein, that there was a significant increase in the axis positioning error on account of an increase in the temperature of the machine elements due to continuous operation. However, it was also observed that the specific operating parameters of the test cycles carried out also significantly affected the positioning error. Different sets of operating parameters generated significantly different error values even though the temperature of the machine elements generated by those operating conditions was similar. As such, this observation forms a very important consideration in the development of a generic thermal error compensation system. It appears to indicate that such a system needs to be capable of evaluating the compensation depending upon the temperature values of the machine elements as well as account for the effect that different operating parameters induce upon the positioning error under the same thermal condition of the machine. This paper attempts to analyse the thermal behaviour of a three-axis vertical machining centre under the influence of various operating parameters and, through the experimental results obtained, point out and explain the effect of these parameters on the axis positioning error. This behaviour forms the basis of an improved modelling methodology that is presented separately in Part II of this paper.     

冷轧工作辊摩擦不稳定分析及其抑制对策

对冷轧机工作辊由于摩擦力引起的垂直、横向振动作了定性分析，指出了它们的危害，提出了预防措施。     

Whole-body vibration exposure in sport: four relevant cases

This study investigates the whole-body vibration exposure in kite surfing, alpine skiing, snowboarding and cycling. The vibration exposure was experimentally evaluated following the ISO 2631 guidelines. Results evidenced that the most critical axis is the vertical one. The weighted vibration levels are always larger than 2.5 m/s² and the vibration dose values are larger than 25 m/s^1.75. The exposure limit values of the EU directive are reached after 8–37 min depending on the sport. The vibration magnitude is influenced by the athletes’ speed, by their skill level and sometimes by the equipment. The large vibration values suggest that the practice of sport activities may be a confounding factor in the aetiology of vibration-related diseases.