Zeolite synthesis from paper sludge ash with addition of diatomite

BACKGROUND: This study aimed to investigate the synthesis of zeolites from paper sludge ash (PSA) with added diatomite to remove both NH₄⁺ and PO₄^3? for water purification. The PSA had low Si and significant Ca contents. Four types of diatomite: white (T‐W) and brown (T‐B) from deposits of marine origin in Takanosu, and white (S‐W) and gray (S‐G) from lacustrine deposits in Shonai, were added to NaOH solution to increase the Si content and thereby synthesize zeolites with high cation exchange capacity (CEC). RESULTS: The order of the amounts of Si extracted from the diatomite to the alkali solution was S‐W > T‐W = T‐B > S‐G, which correlates with the amorphous SiO₂ content of diatomite. The original ash without addition of diatomite yielded hydroxysodalite with CEC of about 1.0 mmol g^?1. For all samples, the addition of diatomite to the solution yielded zeolite‐P with a higher CEC, but the addition of excess Si inhibited the synthesis of zeolite‐P, and the CEC of the product was low. A product with high CEC including zeolite‐P was obtained in a solution with around 500 mmol L^?1 of Si concentration, and had the ability to remove both NH₄⁺ and PO₄^3?. CONCLUSION: Diatomite has the potential for used as an additive for the synthesis of high CEC zeolite from PSA. The product with zeolite‐P exhibited relatively high CEC, capacity for NH₄⁺ uptake, and the ability to remove PO₄^3? by precipitation, which is preferable for water purification applications. Copyright © 2008 Society of Chemical Industry     

GPS在水面流速流向测量中的应用

传统的水面流速流向测量多采用经纬仪交会法,此法需要大量的人力和设备,工作量大且费时。近几年,随着全球定位系统(GPS)的广泛应用和实践,在一定范围内,采用GPS定位法替代经纬仪交会法施测水面流速流向。介绍了GPS定位法的测量原理、设备,以及测量方法。通过对GPS定位法的精度和优缺点的分析,得出采用GPS定位法施测水面流速流向具有较高的推广价值。     

水上地震折射互换法误差分析

在理论上，用源检互换的方法进行折射地震勘探是没有误差的，在某些特殊条件下无法铺设检波器而又必须进行折射地震勘探时它也是唯一的选择，然而，在实际工作中，由于各种因素的影响，其误差是不可忽略的。为此，本文从地震折射运动学的角度对水上地震折射互换法因过河钢丝绳的重量、水的流速和流向、炮点深度等客观因素造成的解释误差进行了分析，揭示了水上地震折射互换法应注意的问题。这对水上地震折射互换法的资料解释进行误差校正提供了理论基础。     

Surface characterization of PET nonwoven fabric treated by He/O2 atmospheric pressure plasma

The surface of polyethyleneterephthalate (PET) nonwoven fabric was modified by He/O₂ atmospheric pressure plasma treatment, varying plasma exposure time. The plasma treated PET surfaces have been analyzed to investigate the chemical nature and morphology of surface by X‐ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM), respectively. The change of wettability was measured depending on plasma exposure time. XPS results indicated the presence of oxygen‐based functional groups on the PET nonwoven fabric surface after plasma treatment and oxygen content increased as exposure time increased. The mean roughness increased after 30 s exposure and further increase in exposure to 60 s led to decrease of the roughness and then again increase. The root mean square roughness followed the similar trend to mean roughness. The average difference in height, Rz, increased after plasma exposure for 30 s, while it slightly decreased after 60 s exposure. Despite of redeposition, the Rz of 90 s exposed sample increased more than two times compared with those of 30 and 60 s exposed. Wettability increased progressively up to 10 times after 90 s exposure compared with the untreated. It is attributed to the increases of hydrophilicity and surface roughness. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of olive residue benzylation on the thermal and mechanical properties of poly(vinyl chloride)/olive residue composites

The changes in mechanical properties, the thermal stability, and the water absorption capacity of poly (vinyl chloride)/olive residue flour composites were studied as a function of various residue olive flour ratios, i.e., 0, 5, 15, and 25% by weight taking into account the effect of benzylation chemical treatment of the filler. The study showed that composite samples prepared with the untreated filler exhibited higher tensile modulus and hardness compared with the neat resin, whereas elongation and tensile strength were observed to decline. On the other hand, the PVC hardness was found to increase with addition of the untreated olive residue flour (ORF), however the composite samples prepared with the benzylated flour exhibited lower hardness than those prepared with untreated olive residue. Moreover, the amount of absorbed water depends on the amount of filler in the composite. The comparison of the results obtained from the samples of F5, F20, and F30 formulations between the untreated and treated ORF indicated a reduction in absorbed water for the composite samples containing treated ORF with benzyl chloride. As a result, the mechanical properties of the treated composites were improved. Furthermore, the thermal characterization of the different samples carried out by color change test and thermogravimetric analysis revealed an increase in the onset temperatures of decomposition for the treated composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of Li+ ions on structure,properties, and actuation of cellulose electro‐active paper actuator

We have reported an electro‐active paper actuator from regenerated cellulose. After dissolving cellulose fibers with a solution of lithium chloride in N,N‐dimethylacetamide, cellulose was regenerated by combining distillation of cellulose solution along with washing with the mixture of deionized water, isopropyl alcohol, and running water. However, the effect of Li⁺ ions on structure, properties, and the actuation behavior of the actuator was not studied. This article describes the changes in these parameters when the Li⁺ ions are removed by subjecting it to different running water exposure time. The structure and properties of cellulose electro‐active paper and its actuation behavior were studied. As Li⁺ ions content reduced from 4354.17 to 10.26 ppm by increasing the exposure time of running water, crystallinity, Young's modulus, and bending displacement decreased. Details about the investigation have been explained. This elimination of ions is important to increase the piezoelectric effect in EAPap by decreasing the ion migration effect. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

江苏复杂断块高含水单元改善水驱效果的技术对策

在分析高含水开发单元特点的基础上,针对该阶段剩余油的品位、分布和油水关系极为复杂、挖潜难度大的技术难点,提出了适合江苏复杂断块油田高含水开发单元改善水驱开发效果的思路和工作程序、技术对策,并在真武油田高含水开发单元进行了实际应用,取得了良好的效果.     

罗坡坝水电站泄水建筑物设计及试验研究

罗坡坝水电站拱坝设置有三个溢流表孔,中间孔高程低于两侧的孔,三个泄水孔设有差动式挑坎。通过模型试验表明,不发生危及岸坡稳定的泄流雾化问题,此外,适当控制泄流水舌射程可以减少坝下冲坑深度,消能效果良好。     

Photocatalytic degradation of methyl tert‐butyl ether (MTBE) in contaminated water by ZnO nanoparticles

BACKGROUND: Over the past several decades methyl tert‐butyl ether (MTBE) as additive to gasoline, intended to either boost ratings of fuel or to reduce air pollution, has been accepted worldwide. Since MTBE has high water solubility, the occurrence of fuel spills or leaks from underground storage tanks or transferring pipeline has led to the contamination of natural waters. In this study the degradation of aqueous MTBE at relatively high concentrations was investigated by a UV‐visible/ZnO/H₂O₂ photocatalytic process. The effects of important operational parameters such as pH, amount of H₂O₂, catalyst loading and irradiation time were also investigated. Concentration of MTBE and intermediates such as tert‐butyl formate and tert‐butyl alcohol were measured. RESULTS: Time required for complete degradation increased from 20 to 150 min when the initial concentration was increased from 10 to 500 mg L^?1. The first‐order rate constants for degradation of MTBE were estimated to be 0.183–0.022 min^?1 as the concentration increased from 10 to 500 mg L^?1. Study of the overall mineralization monitored by total organic carbon analysis showed that at an initial concentration of 100 mg L^?1 MTBE complete mineralization was obtained after 100 min under UV‐visible/ZnO/H₂O₂ photocatalysis. CONCLUSION: The data presented in this paper clearly indicated that UV‐visible/ZnO/O₂ as an advanced oxidation process provides an efficient treatment alternative for the remediation of MTBE‐contaminated waters. Copyright © 2008 Society of Chemical Industry     

Determination of the total concentration and speciation of Al(III) in tea infusions

The aluminium species in different tea infusions were investigated, by determining their stability constants and concentration. This was done for some particular samples using a simple experimental method based on the sorption of aluminium on the strongly sorbing resin Chelex 100, by a batch procedure. From the thermodynamic information obtained it is possible to calculate the concentration of the different species, and in particular that of the free metal ion, which is very important for evaluating the adsorption of aluminium on biological membranes. It was found that aluminium in the tea infusions here considered is present at high total concentration, approximately 0.1 mM, but mainly linked to strong complexes, for instance with side reaction coefficient higher than 10(5.11) at pH 3.95 in one case (tea 1). This could be the reason for the low toxicity of aluminium in tea. These strong complexes were not dissociated even in the presence of Chelex 100. In this case only a limiting value of the reaction coefficient could be evaluated. The presence of the very strong complexes was found in all the tea sample here considered. In two of the considered samples (one black and one green tea) a part of Al(III) was linked to less strong complexes, for example with a reaction coefficient 10(4.14) (tea 2, pH 4.20). The presence in the considered tea infusions of other substances able to complex aluminium was also detected, by the well known ligand titration procedure, at concentration ranging from 0.65 to 3.37 mM in three tea infusions, and at somewhat higher concentration in the case of the ready drink, which was also considered for comparison.