Edge detection,three-dimensional cell boundary reconstruction and volume and surface area estimation from differential interference contrast images

Three-dimensional (3-D) cell morphology is important for the understanding of cell function and can by quantified in terms of volume and surface area. Differential interference contrast (DIC, or Nomarski) imaging can enable cell edges to be clearly visualized in unstained tissue due to the slight difference in refractive index between aqueous media and cytoplasm. DIC is affected in only one direction - the direction of the optical shear. A 1-D edge detector was used in that direction with a scale length equal to that of an in-focus edge to highlight cell boundaries. By comparison with the signal from the edge detector on an out-of-focus slice, the in-focus slices could be segmented and, after noise suppression, cell outlines obtained. A voxel paradigm was used to calculate cell volume and differential geometry was used for surface area estimation. We applied this approach to obtain 3-D dimensional information by optical sectioning of motile Amoeba proteus.     

Progress in deep-UV photoresists

Higher resolution can be achieved in lithography by decreasing the wavelength of the exposure source. However, resist material and their processing are also important when we move to a shorter wavelength lithography technology. This paper reviews the recent development and challenges of deep-UV photoresists and their processing technology.     

中子产额大于1.5×10^10n／s的密封中子管

报道了一种中子产额大于１．５×１０１０ｎ／ｓ、靶和离子源都可拆卸的密封中子管，以它为核心研制的密封中子发生器已被用于中子照像等领域，并取得了较好的结果。     

从长贮试验看引信零件表面处理方式选择

总结了历年长贮试验情况，分析了防腐层变化的原因，指出了引信零件在选择表面处理方式时应注意的问题。     

Alkali-metal Na Adsorption and Promoted Oxidation on Si(100)2×1 Surface

The alkali-metal Na adsorption on Si(100)2×1 surface and its promoted oxidation and Si oxidegrowth have been investigated by means of thermal desorption,work function,Auger electronspectroscopy and photoemission electron spectroscopy.The experimental data showed that therewas a new state,interface electron state,near the Fermi level after the deposition of Na atoms.It wasfound that the presence of Na always caused an increase of the oxygen initial uptake whereas thepromotion of Si oxide growth was observed only at the coverage of Na greater than 0.5 ML.A newmechanism of Na-promoted Si oxide growth is suggested in this paper.     

离子注入对Cr12MoV钢表面组织结构和力学性能的影响

研究了Ｃｒ１２ＭｏＶ钢离子注入层的显微组织特征及其对表面性能的影响。结果表明，离子注入使Ｃｒ１２ＭｏＶ钢的表面硬度和耐磨性能得到显著改善，且存在着一个最佳的注入剂量，约为３×１０＾１＾７Ｎ＾＋／ｃｍ＾２左右。离了注入在Ｃｒ１２ＭｏＶ钢表面层中形成了大量细小弥散的第二相粒子，并使α－Ｆｅ晶格发生严重畸变，从而引起材料表面强化。     

基底元素表面富集与扩散阻档层

根据An－Ag系统以及An－Cu系统的扩散系数计算，提出了扩散阻挡层模型。利用这个模型对Au－Ag系统进行有关实验，得利了较好的验证。     

The As-prepared surfaces of C-axis-oriented Nd1Ba2Cu3Oy thin films characterized using scanning probe microscopes

Recently, superconducting Nd₁Ba₂Cu₃O_y (Ndl23) thin films with high superconducting transition temperature (T _c) have been successfully fabricated at our institute employing the standard laser ablation method. In this paper, we report the results of surface characterization of the Nd123 thin films using an ultrahigh vacuum scanning tunneling microscope/spectroscopy (UHV-STM/STS) and an atomic force microscope (AFM) system operated in air. Clear spiral pattern is observed on the surfaces of Nd123 thin films by STM and AFM, suggesting that films are formed by two-dimensional island growth mode. Contour plots of the spirals show that the step heights of the spirals are not always the integer or half-integer number of thec-axis parameter of the structure. This implies that the surface natural termination layer of the films may not be unique. This result is supported byI-V STS measurements. The surface morphology of the Nd123 thin films is compared with that of thec-axis-oriented Y₁Ba₂Cu₃S_y thin films. Surface atomic images of the as-prepared Nd123 thin films are obtained employing both STM and AFM. STS measurements show that most of the surfaces are semiconductive. The results of STS measurements together with the fact that we are able to see the surface atomic images using scanning probe microscopes suggest that exposure to air does not cause serious degradation to the as-prepared surfaces of Nd123 thin films.     

A Survey of Inverse Surface Design From Light Transport Behavior Specification

Inverse surface design problems from light transport behavior specification usually represent extremely complex and costly processes, but their importance is well known. In particular, they are very interesting for lighting and luminaire design, in which it is usually difficult to test design decisions on a physical model in order to avoid costly mistakes. In this survey, we present the main ideas behind these kinds of problems, characterize them, and summarize existing work in the area, revealing problems that remain open and possible areas of further research.     

钢纤维混凝土在南钢大道工程中的应用

钢纤维混凝土是一种性能优良的新型复合材料，与普通混凝土相比，其抗拉、抗弯、抗裂及耐磨、耐冲击、耐疲劳等性能都有显著提高，它不仅可使路面厚度减薄，工程缝间距加大，改善路面的使用性能，延长路面使用寿命，而且还可节省工程造价，缩短施工工期。文中结合南钢大道路面工程实际，主要介绍了钢纤维混凝土的施工及质量控制要点。