锚索测力计有关应用问题的探讨

通过分析锚索测力计因受力状态不同而带来的系统误差,提出了测力计实测锚固力的修正方法及部分测力计传感器失效后延续锚固力测值的计算方法.     

Effect of processing conditions on the yield and failure response of an aliphatic polyketone terpolymer

The effect of processing conditions on the yield and failure behavior of an aliphatic polyketone terpolymer was studied. Testing and characterization were performed on samples that were extruded in the form of hollow cylinders. We performed the extrusion process at different shear rates and at different cooling rates to assess the effect that process conditions had on the polymer properties. We performed biaxial testing on the samples to characterize the failure envelopes, including the ductile–brittle transition condition for each process condition. The effect of shear rate was negligible, whereas the cooling rate significantly affected the failure behavior. To explain these differences in behavior, we performed characterization via differential scanning calorimetry, wide‐angle X‐ray diffraction, attenuated total reflection IR spectroscopy, dynamic mechanical thermal analysis, scanning electron microscopy, and residual stress measurements. A broad glass transition was found for all samples at temperatures higher than previously reported for this material. Alteration of the processing conditions did not influence the crystalline phase (percentage crystallinity, crystalline orientation, crystallite size, etc.). A change in spherulitic structure was also observed with altered cooling rate and is suggested to have contributed to the change in failure behavior. Residual stresses also affected the behavior of all samples. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 318–334, 2002; DOI 10.1002/app.10334     

紧凑 Tokamak(球形环)聚变堆第一壁及中心导体柱上中子负荷及核热计算与分析

采用通用蒙特卡罗粒子输运程序ＭＣＮＰ／３８计算低环径比Ｔｏｋａｍａｋ（紧凑环或球形环）聚变堆第一壁及中心导体上的中子壁负荷分布和核热沉积分布，并与常规Ｔｏｋａｍａｋ堆第一壁上中子壁负荷分布和核热沉积分布进行比较、分析。结果表明，在中子壁负荷归一化为１ＭＷ／ｍ２时，与常规Ｔｏｋａｍａｋ相比，在低环径比Ｔｏｋａｍａｋ堆第一壁及中心柱表面上中子壁负荷分布峰值并不比常规Ｔｏｋａｍａｋ堆第一壁上的峰值高，而且低于低环径比Ｔｏｋａｍａｋ堆整个第一壁上的平均值，而中心柱上的核热沉积峰值稍高于常规Ｔｏｋａｍａｋ堆第一壁上的核热沉积峰值，但对较高中子壁负荷情况，中心导体柱上的核热沉积和辐照损伤仍可能是比较严重和值得特别研究的问题。     

小眼井最优水力学设计及分析

在充分考虑小眼井钻井特点和合理确定环空压耗的基础上，将喷射钻井理论和环空携岩理论有机结合起来，导出了在两种工作方式下优化设计小眼井钻井水力参数模型，并开发了应用软件。通过实例计算，提出了在小眼井最优水力学设计中采用最大水功率工作方式的重要性，并建议在大眼井的水力参数设计中考虑钻柱的偏心、旋转和钻杆接头对环空压耗的影响。     

Multiobjective dynamic load-dispatching method for optimal operation of power systems

A new practical method is proposed which gives a quasi-optimal solution of the dynamic load-dispatching problem formulated by a multiconstraint multiobjective optimization problem. Here, the multiple constraints are rate reserve constraints and power flow ones, and the multiple objectives are fuel cost and CO₂ emission. The proposed method is an integration of the following three techniques: (1) “Group Dispatch Scheme,” which is developed by the authors, is used to satisfy a violated constraint easily. This scheme consists of three steps. The first step is to classify all generators into two groups. One is the group which should be more loaded to satisfy the violated constraint, and the other is the should-be less loaded group. The second step is to add some load to the former group, and to subtract the same load from the latter. The third step is to dispatch each group load to each groups generators, respectively; (2) the dynamic load-dispatching algorithm is used which provides, in practical time, quasi-optimal generation trajectories; (3) the conventional weighting parametric method is used to obtain a Pareto optimal solution of multiobjective problems. The effectiveness of the method is clarified by a computer simulation on the actual power system of Kansai Electric Power Company.     

太钢3#高炉重力除尘器大件吊装

太钢3#高炉大修改造是集团公司重点外部工程项目之一，工程量大，工期紧，施工场地狭小，而质量要求较高。如何采取科学、经济的设备吊装方案，对整个项目经济指标的实现，意义重大。文章详细介绍了太钢3#高炉重力除尘器大件整体吊装方案。通过实际采用，取得良好的经济效果。     

本钢7号高炉中控室10kV供电系统技术分析及改进方案实施

根据7号高炉中控室供电状况，进行了供电平衡分析。调整两段负荷，使供电平衡安全。     

应力、强度呈非正态分布时可靠度公式的推导

介绍一种当应力、强度呈非正态分布时的可靠度的计算方法,以用来进行机械可靠性设计,并以一个地震载荷的直立压力容器为例加以说明。     

水轮机调速器与电网负荷频率控制

在现代电力系统中，水轮机调速器已成为水轮机控制系统的控制核心。文中叙述了水轮机调速器与电网负荷频率控制之间的关系，分析了调速器在电网一次调频、二次调频中的作用、静态特性和动态特性;通过建模、仿真及现场试验，提出了机组并联于大电网工况下的调速器PID参数整定范围和应有的机组功率控制模式。     

空气调节中加湿处理的方案选择--某商标编织车间的空调设计

本文针对散热量大 ,散湿量小并要求控制室内相对湿度的场所进行了空调方案的分析比较 ,由此选择了一种比较节能和节省投资的空调设计方案。