Service life planning and performance requirements

Service life planning comprises a model for the determination of a reasonable expected service life for buildings and components, and it establishes a routine for the assessment of design alternatives. A design option is considered reasonable when it meets or exceeds performance requirements over time that have been drawn up specifically for the specific project. Due to this assessment reference, there is a very evident link to the concept of performance-based building. Any stakeholder involved in the value chain or in the design process of the building, as well as regulators and building users, can express performance requirements. Identified requirements, both in relevance and in quality, will vary with the stakeholder and his/her perspective of interest. As building sector manufacturers develop most products with reference to standards rather than with reference to specific requirements, there is no direct link from user requirements to the product design. Instead, the building designer has the responsibility to ensure performance requirements are met by the performance of products integrated into the design. As these design decisions also have to be made at the material and component level, a performance-based building would benefit from an established rationale that enables the communication of performance requirements across the relevant system levels in the relevant design processes. A path for the connection of the established concepts of service life planning and performance-based building is presented. The aim is to identify key elements that need to be developed for the successful linkage of performance-based building with service life planning.     

提高E^2PROM中NMOS管源漏穿通电压的实验研究

为了提高Ｅ＾２ＰＲＯＭ中Ｎ管源漏穿通电压，用实验的方法对制造工艺进行了研究。结果表明，高能量注入是提高ＶＰＴ的有效手段，但受到ｐｎ结击穿的限制，只适用于低区短沟Ｎ管；ＤＤＤ工艺大幅度高ＶＰＴ，但ｐｎ结击穿电压低于２０Ｖ，不能应用于高压ＭＯＳ管；采用适量的防穿通注入和适当增大沟道长度为最理想的工艺途径。     

Enhanced Oil Recovery: The Synthesis of Anthraquinone [1, 2-C] Alkylisoxazole

Anthraquinone [1, 2-C] methylisoxazole is synthesized from 2-ethylanthraquinone through nitration and treating with oleum. The different methods of 2-ethylanthraquinone nitrated were discussed. The optimum conditions were determined. The structure of the product was confirmed by MS and ¹H NMR.     

Distinction between enzymically and chemically catalyzed interesterification

The 1,3-specific lipase-catalyzed interesterified fats were distinguished from chemically catalyzed products by the fatty acids in the 2-position. The fatty acid contents in the 2-position of the 1,3-lipase-catalyzed and the original triglycerides were similar but different from that of chemically interesterified fat. Also, the saturated-to-unsaturated fatty acid ratio in the 2-monoglycerides was lower for the 1,3-specific lipase-catalyzed interesterified fats than for the corresponding chemical products.     

Solid-liquid phase equilibria of benzene + 2-methyl-2-propanol system under high pressures

Solid-liquid phase equilibria of the benzene + 2-methyl-2-propanol system have been investigated at temperatures from 278 to 323 K and pressures up to 300 MPa using a high-pressure optical vessel. The uncertainties of the measurements of temperature, pressure and composition are within ±0.1 K, ±0.5 MPa, and ±0.001 mole fraction, respectively. The freezing pressure at a constant composition increases monotonously with pressure. The eutectic point shifts to a higher temperature and benzene-rich composition with increasing pressure. In order to describe the pressure-temperature-composition relation of high-pressure solid-liquid phase equilibria, a new simple equation has been proposed as follows:

FTIR investigation of ethylene coordination and polymerization on reduced Cr/SiO2 catalyst

FTIR spectroscopy was applied to study the initial steps of ethylene polymerization on reduced chromia-silica (0.5 wt% Cr/SiO₂). To decrease the speed of the reaction small doses of gas were introduced to the catalyst in each run and C₂D₄ was used to confirm band assignments. At the initial steps of the reaction only ethylene molecules coordinated to probably Cr _A ²⁺ cations were observed. The concentration of such complexes was estimated to be about 50% of the total amount of Cr atoms in the sample. The FTIR spectrum of the polymer formed at the initial doses of C₂H₄ (when [C₂H₄] [Cr]) was found to be slightly different from that formed after excess ethylene was introduced onto the catalyst ([C₂H₄] > [Cr]).     

基于J2EE平台的供应链管理系统研究

介绍了供应链管理的基本原理和实现技术，从平台基础、移植性、扩展性等多个角度对J2EE平台进行了相应的分析，提出了一个基于J2EE平台的供应链管理系统框架，并从系统结构、系统功能模块等方面进行了说明。     

低电压氧化锌压敏电阻器的研究

研究了一种制造低电电压氧化锌压敏电阻器的方法。在基本成分的基础上适当加入二氧化钛可降低梯度电压（Ｖ１ｍＡ／ｍｍ），适量掺硼和改进热处理工艺可减小元件的漏电流和提高其稳定性。     

Site occupations and ordering behaviour of O phase in Ti2AlNb—based intermetallics

1　ＩＮＴＲＯＤＵＣＴＩＯＮＴｈｅｏｒｔｈｏｒｈｏｍｂｉｃａｌｌｏｙｓａｒｅｏｆｇｒｅａｔｔｅｃｈ ｎｏｌｏｇ ｉｃａｌｉｎｔｅｒｅｓｔｉｎｈｉｇｈｔｅｍｐｅｒａｔｕｒｅａｐｐｌｉｃａｔｉｏｎｓｓｉｎｃｅｔｈｅｙｈａｖｅａｇｏｏｄｂａｌａｎｃｅａｍｏｎｇｓｔ     

石英砂的相变与换向器套筒铸件的变形

用呋喃树脂石英砂工艺生产牵引电机换向器套筒出现变形、裂纹等铸造缺陷,是由石英砂相变膨胀引起,后用高铬刚玉砂代替石英砂得到解决.