国际放射防护委员会的剂量系数的可靠性

在评价公众成员摄入放射性核素的辐射危害时，需估算每单位摄入量所致的剂量。摄入放射性素后器官或民受到的剂量是受到的剂量是通过生物学模型和剂量学模型来确定的，因此剂量也必须根据模型来确定。文中初步探讨了国际放射防护委员会给出的剂量系数的可靠性问题。文中首先说明了估算剂量系数的概念和方法，然后分析了剂量系数估算中，采用胃肠道模型，呼吸道模型，系统生物动力学模型和剂量学模型所遇到的不确定度的各种主要来源。     

烧成及热处理工艺对钛酸锶铅基热敏材料性能及显微结构的影响

研究了烧成及热处理工艺对钛酸锶铅基热敏材料的阻温特性及显微结构的影响。通过扫描电镜（ＳＥＭ）和能量分散仪（ＥＤＡＸ）分析了材料的显微结构及不同形貌晶粒的成份。通过对组成、烧成及热处理工艺的控制，可得到具有Ｖ型ＰＴＣＲ特性的热敏材料。     

工业工程继续教育和高等教育自学考试方案研究

根据作者参与工业工程（ＩＥ）研究和学术活动的实践，阐述了如何把学习国外先进经验与中国国情相结合，并以机电制造工业为主要对象，研究和设计了ＩＥ专业继续教育和高等教育自学考试教学计划。同时说明了该计划的实施，为大批培养社会迫切需要的ＩＥ人才创造了条件，并对我国ＩＥ学科建设起到了积极的推动作用。     

2,4-二氯氟苯的合成

论述了2，4－二氯氟苯合成的新方法。以对氯硝基苯为起站原料，经氟化反应、硝化反应及氯化反应制得2，4-二氯氟苯，总收率达59．0％。本合成路线工艺简单、操作安全、原料易得、成本低廉，适合于工业化生产。     

高速钢W6Mo5Cr4V2的脱磷试验

在３０ｋｇ感应炉上用ＣａＯ－Ｎａ２ＣＯ３－ＣａＦ２－ＦｅｘＯ（ＭｏＯ３）渣、ＭｏＣｌ６粉剂和Ａｌ－Ｃａ合金作脱磷剂对高速钢Ｗ６Ｍｏ５Ｃｒ４Ｖ２进行脱磷试验。结果表明，ＣａＯ－Ｎａ２ＣＯ３－ＣａＦ２－ＦｅｘＯ渣的脱磷效果最好，一般脱磷率可达２６％￣５６％。     

Preparation and Properties of Sintering Additives Coated Si3N4 from Heterogeneous Nucleation Processing

The sintering additives such as Al2O3 and /or Y2O3 were coated on the surfaces of Si3N4 particles via heterogeneous nucleation processing using a buffered pH solution as the precipitation reagent .They nucleated and grew only on the surfaces of Si3N4 and did not form sol particles in solution by TEM observation .The isoelectric point(IEP) of coated Si3N4 was different from that of as-received Si3N4.The IEP of Al(OH)3-coated Si3N4 occurred at pH8.4, which is close to that of alumina .When Al(OH)3-coated Si3N4 particles were coated with Y(OH)3,the IEP of coated Si3N4 powder shifted from pH8.4 to pH9.2 ,similar to that of yttria.In addition ,the rheological data showed that Al2O3 and /or Y2O3 coated Si3N4 suspension is nearly Newtonian and that added Si3N4 suspension shows a shear rate thinning behavior.     

测井数据实时采集与接口设计

介绍了一种采用改进型的ＣＬＳ３７００数控测井系统对微电阻率扫描仪数据采集与控制接口的设计及实现方法。基于ＣＬＳ３７００数控测井仪和ＦＭＳ仪采用８９Ｃ５１单片机设计出通信接口，解决了微电阻率方法。基于ＣＬＳ３７００数控测井仪和ＦＭＳ仪采用８９Ｃ５１单片机设备出通信接口电路，解决了微电阻主扫描仪现现场实时处理中的瓶颈问题。     

STI process steps for sub-quarter micron CMOS

This paper presents Shallow Trench Isolation (STI) process steps for sub-1/4 μ CMOS technologies. Dummy active areas, vertical trench sidewalls, excellent gap filling, counter mask etch step and CMP end point detection, have been used for a 0.18 μm CMOS technology. Electrical results obtained with a 5.5 nm gate oxide thickness show good isolation down to 0.3 μm spacing. Good transistor performances have been demonstrated.     

A comparison of leaf-spring with aircushion trailer suspensions in the transport environment

Packaging engineers need to be able to accurately determine the forces present in the shipping environment in order to protect packaged goods. The purpose of this study was to determine the vertical vibration levels measured in three separate truck-trailer suspension systems; conventional leaf-spring, conventional air-ride and damaged air-ride. The main conclusion reached in this study is that the air-ride suspension when maintained gives lower power density (PD) levels on all road surfaces studied. A damaged air-ride suspension and leaf-spring suspension are very similar in response frequencies, although the damaged air-ride produces higher vibration levels at lower frequencies.