Prediction of evaporation heat transfer coefficient and pressure drop of refrigerant mixtures

A study on the prediction of heat transfer coefficient (HTC) and pressure drop of refrigerant mixtures is reported. HTCs and pressure drops of prospective mixtures to replace R12 and R22 are predicted on the same cooling capacity basis. Results indicate that nucleate boiling is suppressed at qualities greater than 20.0% for all mixtures and evaporation becomes the main heat transfer mechanism. For the same capacity, some mixtures containing R32 and R152a show 8.0–10.0% increase in HTCs. Some mixtures with large volatility difference exhibit as much as 55.0% reduction compared with R12 and R22, caused by mass transfer resistance and property degradation due to mixing (32.0%) and reduced mass flow rates (23.0%). Other mixtures with moderate volatility difference exhibit 20.0–30.0% degradation due mainly to reduced mass flow rates. The overall impact of heat transfer degradation, however, is insignificant if major heat transfer resistance exists in the heat transfer fluid side (air system). If the resistance in the heat transfer fluid side is of the same order of magnitude as that on the refrigerant side (water system), considerable reduction in overall HTC of up to 20% is expected. A study of the effect of uncertainties in transport properties on heat transfer shows that transport properties of liquid affect heat transfer more than other properties. Uncertainty of 10.0% in transport properties causes a change of less than 6% in heat transfer prediction.     

Deformation analysis of skew ruled surface shells by moiré interference

The use of thin film grids coated on surfaces is described in relation to the determination of deformations in doubly curved shells. The technique is called the coating film moiré interference method and employs a laser holographic approach.     

Degradation of polyethylene terephthalate films in the presence of lubricants for HFC 134a: a critical issue for hermetic motor insulation systems

Earlier studies conducted in the use of sealed tubes with polyalkylene glycol lubricants and polyethylene terephthalete (PET) films revealed that the PET films exhibited embrittlement and (visual) degradation. This led to an investigation of PET embrittlement mechanisms with the new lubricants used with HFC 134a. The lubricants studied were three polypropylene glycols (the monol, the diol and the completely end-capped glycols), pentaerythritol ester and a blend of monol and ester. The effects of moisture content, temperature and lubricant structure were studied. All lubricants in this study were of viscosity grade ISO-32 (150 SUS). The results were compared to PET film embrittlement in the presence of CFC 12 and mineral oil. This study reconfirmed the earlier findings that the PET films must be dried to lower than 0.1 wt.% moisture content for use in hermetic systems. This paper discusses the effect of the moisture content of the lubricant and the effect of the lubricant structure on PET films. The dependence of the various mechanisms on temperature is shown. Esters and end-capped polyalkylene glycols are recommended for use with HFC 134a.     

Continuous formation of slurry ice by cooling water–oil emulsion in a tube

Water-silicone oil emulsion with an additive, (C₂H₅O)₃SiC₃H₆NH₂, was examined as a heat storage material. A spiral tube used as a heat exchanger was immersed in a low temperature bath and the emulsion was circulated in the tube to make ice continuously. Ice was separated from the ice–liquid suspension in an outlet tank. The amount of formed ice, the temperatures of the inlet and the outlet of the heat exchanger, and the temperatures in the tube wall were measured and the overall heat transfer coefficient and the heat flux through the tube were calculated. Experiments were carried out, varying the flow rate, the temperature of cooling brine, and the thickness of tube wall. The condition under which slurry ice was formed continuously without adhesion of ice to the cooling wall was clarified. Though decrease in the thermal resistance of the tube increased the rate of ice formation or raised the brine temperature, it narrowed the range of the flow rate and of the brine temperature in which slurry ice was formed continuously.     

Effects of calcination temperature on phase and microstructure evolution of BaTi4O9 powders

Calcining of the mixture of BaCO₃ and TiO₂ with a ratio 1:4 at different temperatures was carried out to synthesize BaTi₄O₉ powders. Phase evolution of the samples was studied using the differential thermal analysis (DTA) and X-ray diffractometry (XRD). Both techniques confirmed that the formation of BaTi₄O₉ started around 1000 °C. The XRD peaks showed that BaTi₄O₉ was most pronounced at 1250 °C. X-ray line broadening methods were employed to study the variation of particle size and microstrain of the BaTi₄O₉ powders. The Voigt function in a single line and the pseudo-Voigt function in the variance methods were used in our case. We found that both functions resulted in the same trends, i.e., the particle size increased with the temperature with the biggest size of 180 and 160 nm, whilst the microstrain yielded the opposite trend with the lowest values of 6.2 × 10^–3 and 1.1 × 10^–3. The scanning electron microscopy (SEM) study revealed the size of the large particles formed, due to agglomeration, to be about 0.5–1.9 μm. Furthermore, it was shown that irregular shapes of BaTi₄O₉ powders necked to each other appeared at 1000 °C and grew into ellipse and rod shapes at 1250 °C. Electronic Publication     

Performance of compression/absorption hybrid refrigeration cycle with propane/mineral oil combination

This paper discusses the feasibility of a vapor compression/absorption hybrid refrigeration cycle for energy saving and utilization of waste heat. The cycle employs propane as a natural refrigerant and a refrigeration oil as an absorbent. A prototype of the cycle is constructed, in which a compressor and an absorption unit are combined in series. The performance of the cycle is examined both theoretically and experimentally. Although the solubility of the propane with the oil is not enough as a working pair in the absorption unit, the theoretical calculation shows that the hybrid cycle has a potential to achieve a higher performance in comparison with a simple vapor compression cycle by using the waste heat. In the experiment, the prototype cycle is operated successfully and it is found that an improvement of an absorber is necessary to achieve the good performance close to the theoretical one. The application of an AHE (absorber heat exchanger) can reduce the heat input to a generator. Further examinations on some other combinations of refrigerant/refrigeration oil and additives are desirable.     

脉冲激光沉积SrBi2Ta2O9铁电薄膜电容特性研究

用ＰＬＤ方法成功地制备了ＳＢＴ铁电薄膜，并制作成Ｐｔ／ＳＢＴ／Ｐｔ薄膜电容器。ＳＢＴ薄膜的晶面取向以（００８）和（１１５）为主。在５Ｖ电压下，极化反转，并且得到较饱和的电滞回线，剩余极化强度和矫顽电场分别为８４μＣ／ｃｍ２和５７ｋｖ／ｃｍ。ＩＶ特性测试显示两个对称的双稳峰，并得到零电压下，面积为３１４×１０４μｍ２，厚度为０３５μｍ的电容器，电容约为５６０ｐＦ，介电常数约为６００。疲劳测试表明Ｐｔ／ＳＢＴ／Ｐｔ具有优良的抗疲劳特性。     

8-R-9苄基-9H-嘌呤衍生物的合成研究

采用 (Ph3 P) 2 PdCl2 为催化剂 ,DMF为溶剂 ,对 8 碘 9 苄基 9H 嘌呤与有机锡试剂RSnBu3 (R=乙烯基、2 噻吩基、2 呋喃基、苯乙炔基和苯基等 )之间的Stille偶合反应进行了研究 ,合成出了5种 8位取代的嘌呤衍生物。在反应温度为 80℃ ,n(8 碘 9 苄基 9H 嘌呤 )∶n (RSnBu3 )∶n〔(Ph3 P) 2 PdCl2 〕 =1 0∶1 2∶0 0 5的较佳工艺条件下 ,产品收率 4 1%～ 91%。用1H NMR、13 C NMR和MS对产物进行了表征     

K0.9Li0.1（Ta0.5Nb0.5）O3晶体压电应变系数的测量

用准静态ｄ＿（３３）测量仪和干涉法相结合。测量了Ｋ＿（０．９）Ｌｉ＿（０．１）（Ｔａ＿（０．５）Ｎｂ＿（０．５）Ｎｂ＿（０．５））Ｏ＿３晶体的压电应变系数。结果为：ｄ＿（３３）＝８６．０，ｄ＿（３３）＝一２９．５，ｄ＿（１５）＝１１２．９×１０￣（－１２）Ｃ／Ｎ．     

Synthesizing plans that contain actions with context-dependent effects1

This paper presents a method of solving planning problems that involve actions whose effects change according to the situations in which they are performed. The approach is an extension of the conventional planning methodology in which plans are constructed through an iterative process of scanning for goals that are not yet satisfied, inserting actions to achieve them, and introducing subgoals to these actions. This methodology was originally developed under the assumption that one would be dealing exclusively with actions that produce the same effects in every situation. The extension involves introducing additional subgoals to actions above and beyond the preconditions of execution normally introduced. These additional subgoals, called secondary preconditions, ensure that the actions are performed in contexts conducive to producing the effects we desire. This paper defines and analyzes secondary preconditions from a mathematically rigorous standpoint and demonstrates how they can be derived from regression operators.