钻杆防磨技术的现状和发展

在深井超深井勘探过程中，由于径向力、涡动、横向振动等因素的存在，随着钻井时间的增长，钻柱作用于套管内壁的侧向力增大，导致套管磨损的问题越来越严重。介绍了近年来钻杆防磨技术的发展，主要从钻杆接头表面处理和钻杆保护器2方面来研究防磨减磨措施的现状和发展。     

挠性抗回旋PDC钻头的有限元分析

回旋是导致PDC钻头早期失效的主要原因，介绍了一种基于挠性钻头的构想设计的抗回旋PDC钻头，阐述了其结构和抗回旋原理。对挠性钻头的公、母接头进行了有限元应力分析，说明了模型建立、网格划分以及约束和载荷施加过程中所采用的方法和关键技术。有限元分析结果表明挠性钻头的强度满足要求。     

面向表面组装工艺技术的PCB焊盘设计

尽管电子设计类软件已相当先进和方便，而且更新速度也很快，但是仍然无法满足各个层次的设计人员的需求，特别是适合各种元素封装形式的焊盘设计库并不能让设计和制造者满意，为了在此方面对PCB设计有所帮助，从印制电路板焊盘的设计方法入手，针对表面组装工艺技术特点，分析了PCB焊盘对PCA可靠性的影响因素，并根据相关的质量要求提出了较为简便的设计方案。     

大口径管道带水抢修

包头地区1996年5月3日发生6.4级强烈地震,给包钢生产造成重大损失,地震发生后,包钢生产用动力系统发生多起事故.本文针对4#高炉工业回水管道(φ1220×10)震后发生断裂,如何在保证不停止生产的前提下,采取什么措施进行管道带水抢修进行了阐述,本文是经过现场抢修过程总结而来,对今后大口径管道带水抢修提供了宝贵的经验.     

Ti-23Al-14Nb-3V合金氩弧焊接头的显微组织及其力学性能

研究了预热对Ｔｉ－２３Ａｌ－１４Ｎｂ－３Ｖ合金焊接性，特别是对消除氩弧焊冷裂纹的作用以及对接头显微组织和力学性能的影响。结果表明，焊前预热可有效降低该合金的冷裂倾向。经预热处理后，焊缝区的结晶层状线消失，热影响区的硬度峰得到缓和，整个焊缝的显微硬度分布趋于均匀，但焊缝区的枝晶发生粗化，热影响区有所扩大。焊件接头的拉伸试验表明，预热可使焊缝区的接头强度系数增加，但无论预热与否，接头强度均低于母材强度，且不显示宏观塑性。     

三峡永久船闸结构缝渗漏处理技术

在三峡永久船闸结构缝处理过程中，认真分析了结构缝渗漏的原因，通过止水检查槽进行压水检查，确定了渗漏部位。结合渗漏具体情况，采取了结构缝表面嵌填止水材料和廊道周边止水检查槽灌浆相结合的处理方法。在实施过程中，采用了多种新材料和新工艺，取得了良好的效果。     

广西洛东水电厂增机扩容可行性设计

通过对洛东水电厂的来水量、地质和经济指标等技术资料的分析,认为采用灯泡贯流式机组扩大其装机的容量是可行的。并介绍了洛东水电厂增机扩容的可行性设计情况。     

Suppression of void coalescence in thermal aging of tin-silver-copper-X solder joints

Addressing the potential for drop impact failure of Pb-free interconnects, the shear ductility after extensive aging of Sn-Ag-Cu (SAC) solders has been improved radically by Co or Fe modifications. Several other SAC+X candidates (X=Mn, Ni, Ge, Ti, Si, Cr, and Zn) now have been tested. Solder joint microstructures and shear strength results show that new SAC+X alloys also suppress void formation and coalescence at the Cu (substrate)/Cu₃Sn interface (and embrittlement) after aging at 150°C for up to 1,000 h. Microprobe measurements of 1,000 h aged samples suggest that Cu substitution by X is usually accentuated in the intermetallic layers, consistent with X=Co and Fe results.     

Multi-User MIMO Mobile CDMA Uplink System Employing Turbo Coding and Joint Detection Through a Multipath Rayleigh Fading Channel

In this paper, a generalized multiple-input multiple-output (MIMO) antenna system that can be fitted to the uplink of a wireless communication system is considered for the general case of multi-user. At the transmitter, the information bits are Turbo coded, then interleaved and passed through a serial-to-parallel converter. The channel is assumed bad urban suffering from multipath Rayleigh fading resulting in inter-symbol and multiple access interferences (ISI and MAI). At the front-end of the receiver, a number of receiving antennas are used followed by a joint multi-user estimator based on the Minimum Mean Square Error Block Linear Equalizer (MMSE-BLE).Computer simulations demonstrate a significant performance improvement in both single user and multi-user cases.This paper depends in parts on that presented at the 11th European Wireless Conference, Cyprus, Nicosia, pp. 187–192, April 2005. Yasmine A. Fahmy was born in Guiza, Egypt, on June 4, 1976. She received the B.Sc., M.Sc. and Ph.D. degrees in Communication and Electronics engineering from Cairo University, Egypt on 1999, 2001 and 2005 respectively. She is presently an assistant professor at Cairo University, Egypt. Her current field of interest is wireless communication and channel estimation. Hebat-Allah M. Mourad received her B.Sc., M. Sc. and Ph.D. degrees in electrical communication engineering from Cairo University, Egypt, in 1983, 1987 and 1994 respectively. Since 1983, she has been with the Department of Electronics and Communications, Faculty of Engineering, Cairo University, and is currently associate professor there. Her research interests include optical fiber communications, mobile and satellite communications. Emad K. Al-Hussaini received his B.Sc degree in Electrical Communication Engineering from Ain-Shams University, Cairo, Egypt, in 1964 and his M.Sc and Ph.D. degrees from Cairo University, Giza, Egypt, in 1974 and 1977, respectively. From 1964 to 1970, he was with the General Egyptian Aeroorganization. Since 1970, he has been with the Department of Electronics and Communications, Faculty of Engineering, Cairo University, and is currently professor there. He was a research fellow at Imperial College, London, UK, and at the Moore School of Electrical Engineering, University of Pennsylvania, Philadelphia, PA, USA, in the academic years 1976/1977 and 1981/1982, respectively. In 1990, he received the Egyptian national encouragement award for outstanding engineering research. He has written several papers for technical international journals and conferences. His research interests include signal processing, fading channel communication, modulation, and cellular mobile radio systems. Dr Al-Hussaini is a senior member of IEEE. He is listed in Marquis Whos Who in the World and in the IBC (International Biographical Center, Cambridge) for outstanding people of the 20th century.     

太阳电池板结构应力-应变状态分析

多层胶接是太阳电池板的结构特点,由于不同材料的弹性模量、热膨胀系数和泊松比不同,在温度场 作用下会产生热应力应变,在多次热交变过程中热应力．应变累积最后导致结构层间剥离,因此研究温度场作用 下太阳电池板结构应力应变状态具有非常重要的实际意义。本文推导了模拟太阳电池板结构应力-应变状态的一 维模型,该模型同样适用于分析多层胶接结构应力应变状态。