Transmittance and cathodoluminescence of AlN ceramics sintered with Ca3Al2O6 as sintering additive

Aluminum nitride ceramics were prepared by sintering with 0–4.8 mass% of Ca₃Al₂O₆ (C₃A) as a sintering additive. The transmittance in the range of 260–550 nm increased with increasing amount of C₃A. The cathodoluminescence intensity attributed to oxygen-induced defects decreased with increasing amount of C₃A. From the results, the increase of the transmittance in the range of 260–550 nm was considered to be related to the decrease of the oxygen-induced defect density.     

未增塑聚氯乙烯(PVC-U)异型材配方基础

PVC-U异型材配方十分复杂,常用原料通常在10种以上。根据大连实德集团实际生产情况,这10多种原料通常以7大组分的方式进行配料和生产。文中就该配方中7大组分的分类、特点及应用情况分别进行了详细介绍。     

Formation of composites fabricated by exothermic dispersion reaction in A1-TiO2-B2O3 system

The formation of aluminum matrix composites fabricated by exothermic dispersion reaction in A1-TiO2-B2O3 system was investigated. The thermal analysis results show that the reactions are spontaneous and exothermic. The Gibbs free energy of α-Al2O3 is the lowest among all the combustion products, followed by TiB2 and Al3Ti. It is noted that when the B2O3/TiO2 mole ratio is below 1, the reaction products are composed of particle-like α-Al2O3, TiB2 and rod-like Al3Ti. The α-Al2O3 crystallites, resulting from the reaction between A1 and TiO2 or B2O3, are segregated at the grain boundaries due to a lower wettability with the matrix. SEM micrographs show that rod-like Al3Ti phase distributes uniformly in the matrix. When the BEO3/TiO2 mole ratio is around 1, the Al3Ti phase almost disappears in the composites, and the distribution of α-Al2O3 particulates is improved evidently.     

Preparation and Compressive Stress Effect of Polymer Matrix RE-Fe Giant Magnetostrictive Composite

Polymer matrix RE-Fe giant magnetostrictire composite （GMPC） was prepared using bonding and magnetic field forming technique, and magnetostriction of samples was measured for different compressive stress. The experimental results show thai there is certain compressive effect in GMPC. And the influence of compressive stress on magnetostriction of sample was investigated. It offers essential reference for application and device design of GMPC.     

均匀设计法分析制备过程对钴钼硫化物催化剂机械强度的影响

建立了CoMoP/Al2O3加氢精制催化剂机械强度及其可靠性在制备过程中的数学模型,采用均匀设计考察了浸渍、干燥、煅烧、硫化4个制备过程中,浸渍时间、干燥温度、干燥时间、煅烧温度、煅烧时间、硫化温度和硫化升温速率7个实验因子对催化剂强度均值、Weibull模量的影响,同时考察了这些因素对颗粒密度的影响。方差分析表明所有模型都是充足的。实验结果表明,硫化过程是影响催化剂强度均值的主要过程。在实验范围内提高硫化温度、降低硫化时的升温速率有利于提高催化剂的强度。影响催化剂Weibull模量的因素主要为各个制备过程的交互效应。要提高催化剂强度的可靠性就必须全面考虑催化剂制备的各个过程,特别是各个制备过程的交互效应。     

Average consensus in networks of dynamic agents with switching topologies and multiple time-varying delays

In this paper, we discuss average consensus problem in undirected networks of dynamic agents with fixed and switching topologies as well as multiple time-varying communication delays. By employing a linear matrix inequality method, we prove that all the nodes in the network achieve average consensus asymptotically for appropriate communication delays if the network topology is connected. Particularly, several feasible linear matrix inequalities are established to determine the maximal allowable upper bound of time-varying communication delays. Numerical examples are given to demonstrate the effectiveness and the sharpness of the theoretical results.     

A parallel and scalable algorithm for ADI method with pre-propagation and message vectorization

It is hard to implement the ADI method in an efficient way on distributed-memory parallel computers. We propose “P-scheme” which parallelizes a tridiagonal linear system of equations for the ADI method, but its effectiveness is limited to the cases where the problem size is large enough mainly because of the communication cost of the propagation phase of the scheme.

In order to overcome this difficulty, we propose an improved version of the P-scheme with “message vectorization” which aggregates several communication messages into one and alleviates the communication cost. Also we evaluate the effectiveness of message vectorization for the ADI method and show that the improved version of the P-scheme works well even for smaller problems and linear and super-linear speedups can be achieved for 8194 × 8194 and 16,386 × 16,386 problems, respectively.     

A direct stiffness analysis of a composite beam with partial interaction

The use of the conventional semi-analytical stiffness method in finite element analysis, in which interpolation polynomials are used to develop the stiffness relationships, leads to problems of curvature locking when beam-type elements are developed for composite members with partial interaction between the materials of which it is comprised. The curvature locking phenomenon that occurs for composite steel–concrete members is quite well reported, and the general approach to minimizing the undesirable ramifications of curvature locking has been to use higher-order polynomials with increasing numbers of internal nodes. This paper presents an alternate formulation based on a direct stiffness approach rather than starting from pre-defined interpolation polynomials, and which does not possess the undesirable locking characteristics. The formulation is based on a more general approach for a bi-material composite flexural member, whose constituent materials are joined by elastic shear connection so as to provide partial interaction. The stiffness relationships are derived, and these are applied to a simply supported and a continuous steel–concrete composite beam to demonstrate the efficacy of the method, and in particular its ability to model accurately both very flexible and very stiff shear connection that causes difficulties when implemented in competitive semi-analytical algorithms. Copyright © 2004 John Wiley & Sons, Ltd.     

IF板与08Al板的成形性能研究

通过模拟成形性试验，对新型超深冲用IF钢板和传统冲压用08Al钢板的冲压成形性能进行了研究．结果表明：IF板的拉深性能、扩孔性能、胀形性能以及“拉深-胀形”复合性能等均优于08Al板，其中，扩孔性能和平面各向异性的改善最为显著；各项试验中，IF板的成形力普遍小于08Al板。     

Exchange and oxidation of CO on O-predosed Rh---Al2O3 and Rh---CeO2 catalysts

Exchange and oxidation of C¹⁶O were investigated at 450°C on ¹⁸O-predosed Rh and Pt catalysts supported on A1₂O₃, CeO₂ and CeO₂-Al₂O₃. In all cases, a rapid exchange of C¹⁶O with the surface can be observed. CO oxidation leads to C¹⁶O₂, C¹⁶O¹⁸O and C¹⁸O₂. Significant formation of C¹⁶O₂ is due to the relatively high ¹⁶O coverage in reaction resulting from the C¹⁶O exchange and from an exchange between O surface species and ¹⁶O internal atoms. Hydrogen is also formed via a water-gas shift reaction (CO + surface OH) in higher proportion on CeO₂-containing catalysts than on A1₂O₃. Chlorine inhibits all the reactions (exchange, oxidation and WGS) and particularly the internal exchange.