Comments on “Equivalence of characterizations of fixed models”

In this note we present a proof to the conjecture given in the above paper, and therefore establish the equivalence of characterizations of fixed modes for the general case.     

一种光时分制交换时隙分配计算算法

介绍了一种专为时分复用系统设计的时院分配计算算法。这种算法中主要用到的技术是从一个话务矩阵的各行选出一个区别代表的系统方法。对于任何话务矩阵，这种算法的分配效率都能达到１００％，所产生的模式矩阵个数最多为ｎ２－２ｎ＋２个（对于ｎ×ｎ矩阵）。     

连续挤压法介绍

连续挤压法的特点是：挤压所需的压力是借助一个回转的摩擦轮来实现的。摩擦轮的轮缘上设有一个凹槽，其断面取决于原坯的断面（线材坯料）。本文将就这种工艺的设备和有关铝材生产阶段中的一些问题作一简介。     

镀镍云母导电复合材料的研究

对云母粒子化学镀镍及以LDPE为基材,镀镍云母粒子为填料制备的导电复合材料进行研究。认为此种导电复合材料只有质量轻、强度大及良好的导电等性能。     

Atmospheric and low pressure shadow masked MOVPE growth of InGaAs(P)/InP and (In)GaAs/(Al)GaAs heterostructures and quantum wells

The shadow masked growth technique is presented as a tool to achieve thickness and bandgap variations laterally over the substrate during metalorganic vapor phase epitaxy. Lateral thickness and bandgap variations are very important for the fabrication of photonic integrated circuits, where several passive and active optical components need to be integrated on the same substrate. Several aspects of the shadow masked growth are characterized for InP based materials as well as for GaAs based materials. Thickness reductions are studied as a function of the mask dimensions, the reactor pressure, the orientation of the masked channels and the undercutting of the mask. The thickness reduction is strongly influenced by the mask dimensions and the reactor pressure, while the influence of the orientation of the channels and the amount of undercutting is only significant for narrow mask windows. During shadow masked growth, there are not only thickness variations but also compositional variations. Therefore, we studied the changes in In/Ga and As/P ratios for InGaAs and InGaAsP layers. It appears that mainly the In/Ga-ratio is responsible for compositional changes and that the As/P-ratio remains unchanged during shadow masked growth.     

T8钢—聚有机硅氧烷仿生减粘降阻复合涂层的特性

研究了Ｔ８钢－聚有机硅氧烷仿生减粘降阻复合涂层的表面润湿性，磨料磨损性及土壤的减粘降组性能，与金属材料相比，仿生复合涂层的表面憎水性显著提高，水在其表面上的接触角达９２°；与４５钢相比，其磨料磨损的体积相对耐磨系数为６３％，降阻率达１５．２２％－－２２．２７％。     

粉末布法制备SiC/Ti基复合材料

用粉末布法制备了低成本SiC/Ti基复合材料.结果表明,采用合适的轧制参数即可容易地获得厚度合适、均匀的粉末布;热失重分析和热解残余物分析指出用来制备粉末布的有机粘结剂的去除过程分成两个阶段,合理除气后,基本没有残余物.使用真空热压工艺制备的SiC/Ti基复合材料,纤维分布基本均匀,纤维与基体的界面结合良好.     

Effects of temperature, ammonium and glucose concentrations on yeast growth in a model wine system

In enology, alcoholic fermentation is a complex process involving several mechanisms. Slow and incomplete alcoholic fermentation is a chronic problem for the wine industry and factors leading to sluggish and stuck fermentations have been extensively studied and reviewed. The most studied cause of sluggish and stuck fermentation is the nitrogen content limitation. Nevertheless, other factors, such as temperature of fermentation and sugar concentration can affect the growth of yeasts. In this study we modelled the yeast growth‐cycle in wine model system as a function of temperature, sugar and ammonium concentrations; the individual effects and the interaction of these factors were analysed by means of a quadratic response surface methodology. Cell concentrations and weight loss were monitored in the whole wine fermentation process. The results of central composite design show that lower is the availability of nitrogen, higher is the cell growth rate; moreover, initial nitrogen concentration also influences survival time of Saccharomyces cerevisiae.     

Ermüdungsverhalten und Dauerfestigkeit von Graphit und Aluminium – infiltriertem Graphit

Fatigue behaviour and endurance limit of graphite and of aluminium‐infiltrated graphite Fatigue properties of polycrystalline, isotropic graphite FU2590 and of FU2590 infiltrated with AlSi7Mg (FU2590/AlSi7Mg) were investigated in reversed bending tests at 25 Hz at numbers of cycles below 10⁷ and in tension‐compression tests at 20 kHz below 10⁹ cycles. The open porosity of Graphite (10‐11 Vol.‐%) was infiltrated with the aluminium alloy using the squeeze casting infiltration method, which led to an increase of the bending strength by 50 %, increase of tensile strength by 30 % and increase of stiffness by 15 %. Fully reversed tension‐compression loading of FU2590 delivers a mean endurance limit at 10⁹ cycles at the normalized maximum stresses (i.e. maximum tension stress of a cycle divided by the static strength) of 0,65±0,03. Mean numbers of cycles to failure of 10⁴ were found in fully reversed bending tests at the normalized maximum stress of 0,78. The infiltrated material shows approximately 30 % higher cyclic strength in reversed bending tests, and the mean endurance limit under tension compression loading increases by 15 %. The increased endurance limit of the infiltrated material is caused by the increased stiffness. The increased toughness of graphite due to the infiltration with aluminium is of additional beneficial influence at the higher cyclic stresses investigated in reversed bending tests and in static tests.     

Neutron Stress Measurement of W‐Fiber Reinforced Cu Composite

Stress measurement methods using neutron and X‐ray diffraction were examined by comparing the surface stresses with internal stresses in the continuous tungsten‐fiber reinforced copper‐matrix composite. Surface stresses were measured by X‐ray stress measurement with the sin²ψ method. Furthermore, the sin²ψ method and the most common triaxal measurement method using Hooke's equation were employed for internal stress measurement by neutron diffraction. On the other hand, microstress distributions developed by the difference in the thermal expansion coefficients between these two phases were calculated by FEM. The weighted average strains and stresses were compared with the experimental results. The FEM results agreed with the experimental results qualitatively and confirmed the importance of the triaxial stress analysis in the neutron stress measurement.