泡沫铝的动态压缩性能和吸能性研究

通过测量泡沫铝在动态和准静态压缩条件下的应力 -应变曲线 ,研究了泡沫铝的准静态和动态压缩行为以及不同应变条件下的吸能性 ,并对其应变率效应进行了分析。结果表明 ,在高应变速率和准静态压缩下 ,泡沫铝的σ -ε曲线均表现出弹性变形段、平缓段和密实段三阶段特征 ;泡沫铝的压缩性能具有明显的应变速率敏感性 ,随应变速率的提高 ,流动应力上升 ,吸能性升高     

Evaluation of the reactivity of titanium with mould materials during casting

A methodology for evaluating the reactivity of titanium with mould materials during casting has been developed. Microhardness profiles and analysis of oxygen contamination have provided an index for evaluation of the reactivity of titanium. Microhardness profile delineates two distinct regions, one of which is characterised by a low value of hardness which is invariant with distance. The reaction products are uniformly distributed in the metal in this region. The second is characterised by a sharp decrease in microhardness with distance from the metal-mould interface. It represents a diffusion zone for solutes that dissolve into titanium from the mould. The qualitative profiles for contaminants determined by scanning electron probe microanalyser and secondary ion mass spectroscopy in the as-cast titanium were found to be similar to that of microhardness, implying that microhardness can be considered as an index of the contamination resulting from metal-mould reaction.     

单模光纤的传输衰减随温度变化的研究

本文从实验上测量了单模石英光纤在－50～120℃范围内的损耗。随着温度升高，光纤的损耗随之降低，在常温附近达到最小。其后损耗随着温度的继续升高而增加。损耗的变化主要是由于杂质的吸收和微弯损耗。本文对杂质的吸收以及微弯损耗进行了数值模拟，并且从理论上定性地解释了损耗对温度的依赖关系。     

Absorption of materials by or through the living skin

The skin comes into contact with a large range of materials either deliberately or inadvertently. It should be possible to predict the exact transport rates of these materials through the skin as a function of the physicochemical properties of the different compounds. With this sort of knowledge it is possible to predict the exact disposition of compounds and use this in the formulation of new products both in the pharmaceutical and cosmetic field. The information will also be useful from the standpoint of skin toxicology and environmental health. In order to be able to predict this complex process it is necessary to split the overall transport into different component parts. This article will identify these components and provide illustrations. The major areas discussed will be barrier function of the skin, the release properties of different topical formulations and how these may be monitored. Novel means of enhancing the penetration of drugs will be discussed and how some additives that are incorporated into formulations will perhaps alter the barrier function of skin. A mathematical model describing skin penetration has been developed and its use in predicting blood levels will be described. This model has been tested both in animal experiments and in limited human studies and its relevance to these situations will be highlighted.
Absorption cutanée et transcutanée in vivo     

用稳态反饱和吸收法测量C_（60）的激发态吸收截面

用准连续激光实现了Ｃ６０的稳态反饱和吸收，通过实验和理论计算的拟合，确定了Ｃ６０的三重第一激发态吸收截面。     

The combined effects of curing and environmental exposure on fracture properties of woven carbon/epoxy laminates

This paper concerns a study of the combined effects of curing conditions and environmental exposure on the ultimate properties of two commercial woven carbon/epoxy laminates. Curing parameters (heating rate and applied pressure) were varied so as to obtain six different conditions for each material. Moisture saturation was also achieved by exposing some of the cured samples to environmental conditions of 70°C and 95% relative humidity. Four different tests (tensile, impact, Mode I and Mode II interlaminar fracture resistance) were therefore performed, and the results obtained on the different materials before and after moisture saturation compared. Neither curing pressure nor heating rate nor moisture absorption were observed to have any practical effect on tensile and impact properties. On the contrary, one noticeable effect was the interlaminar fracture resistance of the laminates. The results are discussed and interpreted in terms of damage formation and stress intensification mechanisms.     

用AIR-C2H2原子吸收光谱法测定镉镍电池正极浸渍液中钴含量

本文主要简述与运用AIR-C2H2原子吸收光谱法进行镉镍电池正极浸渍液中钴含量的测定，介绍了钴最佳测定条件及呈良好线性范围的浓度。同时对样品消化处理条件，在测定中样品的干扰因素进行了综合考虑，该方法具有很好的灵敏度，很好的重复性，干扰小，同时具有方法步骤简单，操作容易掌握等特点，对样品钴含量的测定，其相对标准偏差均小于1.0%（n=6），标准加入回收率均在97.0%～102.0%(n=5）范围内，结果表明，运用AIR-C2H2原子吸收光谱法测定镉镍电池正极浸渍液中钴含量的分析，达到了实验室分析质量控制的要求，完全适用于镉镍电池正极浸渍液中钴含量的控制分析和样品系统分析。     

Rapid analysis of polymer homologues and additives with SFE/SFC-MS coupling

A rapid and easy analysis method for polymers is presented. The method involves sample preparation by SFE, separation of the extracted compounds by SFC and simultaneous quantitative detection by FID, as well as identification of unknowns by MS. The applications illustrate how structural research work and routine polymer analysis can be done with this time saving method.     

Volatile constituents of palm wine and palm sap

Palm wine and pasteurised palm sap volatiles were collected, concentrated on a Tenax GC and analysed by gas chromatography and gas chromatography-mass spectrometry. Eighty-two components were identified: 47 esters, 9 alcohols, 5 acids, 6 carbonyls, 2 acetals, 4 terpenes and 9 hydrocarbons. These had all been found previously in conventional wines. Odour evaluation of the separated palm wine components as they eluted suggested that no one compound is responsible for the characteristic palm wine odour. The acetates of higher alcohols and the ethyl esters of straight-chain aliphatic C₆-C₁₀ acids seemed to be important and may play a big role in imparting the fruity nuances of characteristic palm wine odour. Their association with alcohols seemed also to be necessary for the expression of typical palm wine odour. The qualitative difference between palm sap aroma and palm wine aroma appeared to be due mainly to the presence of these esters and alcohols in palm wine and their apparent absence from palm sap, as well as to the presence of some low-boiling esters and alcohols in palm sap and their apparent absence from palm wine.     

A force modulation study on crystallization process in ferroelectric vinylidene fluoride and trifluoroethylene copolymer films

This paper introduces the Force Modulation technique to the study of crystallization process in ferroelectric vinylidene fluoride and trifluoroethylene copolymer films. Using this technique we have successfully visualized ferroelectric crystalline domains and observed that these ferroelectric domains grow out from amorphous phase, unite into strip-like structures, and finally congregate into a union. Force Modulation can weaken the influence of topography on imaging of ferroelectric domains, and reveal more details, which are difficult to be observed in topographical image.